YASKAWA V1000 Product Transition Manual page 34

7 Transfer of Parameter Settings
Reg. Param.
Name
No. No.
Energy Saving
0x01CC B8-01
Control Selection
Accel/Decel Switch
0x020A C1-11
Frequency
Picking up speed and
slowing down rate
0x0264 C1-14
setting standard
frequency
Slip Compensation
0x0212 C3-04 Selection during
Regeneration
0x021C C5-02 ASR Integral Time 1
0x021E C5-04 ASR Integral Time 2
ASR Gain Switching
0x0221 C5-07
Frequency
D1- Frequency Reference
0x0280
01~17 1~17
D3-
0x0294 Jump Frequency 1~3
01~3
Jump Frequency
0x0297 D3-04
Width
Max Output
0x0303 E1-04
Frequency (FMAX)
0x0305 E1-06 Bass Frequency (FA)
Mid Output
0x0306 E1-07
Frequency (FB)
Minimum Output
0x0308 E1-09
Frequency (FMIN)
Mid Output
0x030A E1-11
Frequency 2
Number of Motor
0x0311 E2-04
Poles
34
Description
Energy Savings function enable/disable
selection.
0: Disabled
1: Enabled (set b8-04)
2: PM Energy-saving control
Sets the frequency at which acceleration and
deceleration times are automatically changed.
Sets the base frequency used to calculate
acceleration and deceleration rates.
Enables or disables slip compensation during
regenerative operation.
0: Disabled
1: Enabled (6 Hz and above)
2: Enabled (compensation provided wherever
possible)
Sets the integral time of the speed control loop.
(ASR)
Sets the speed control gain 2 and integral time 2
of the speed control loop (ASR).
Note: Adjustment is not normally required.
Sets the frequency for switching between
Proportional Gain 1, 2 and Integral Time 1, 2.
When ASR switch is set to one of the multi-
function input terminals, that switching value
take priority.
Setting units are determined by o1-03.
Sets the median value of the specific frequency
band that needs to be jumped.
This parameter determines the width of the
deadband around each selected prohibited
frequency reference point. A setting of "1.0" will
result in a deadband of +/- 1.0 Hz.
Sets the maximum output frequency for the V/f
pattern.
Sets the base frequency for the V/f pattern.
Sets the middle output frequency.
Sets the minimum output frequency for the V/f
pattern.
Set only when fine tuning the V/f pattern within
the constant power (HP) range above base speed.
This value seldom needs to be changed.
Sets the number of motor poles. This value is
automatically set during Auto-Tuning.
YASKAWA America, Inc. PL.GA500.01 YASKAWA AC Drive - V1000 to GA500 Transition Guide
Setting Range Initial Setting
GA500 V1000 GA500
A1-02
0~2 0~1 Depend
(all 0)
A1-02
0.0~590.0 0.0~400.0 Depend
(all 0)
0.0~590.0 0.0~400.0 0.0
0~2 0~1 0
0.000~ 0.000~ A1-02
60.000 10.000 Depend
0.000~ 0.000~ A1-02
60.000 10.000 Depend
A1-02
0.0~400.0 0.0~400.0 Depend (all
0)
0.00~ 0.00~
0.00
590.00 400.00
A1-02
0.0~590.0 0.0~400.0 Depend (all
0)
A1-02
0.0~20.0 0.0~20.0 Depend (all
1.0)
A1-02,E1-
03,O2-
40.0~590.0 40.0~400.0
09,E5-01
Depend
A1-02,E1-
03,O2-
0.0~590.0 0.0~400.0
09,E5-01
Depend
A1-02,E1-
0.0~590.0 0.0~400.0 03,O2-09
Depend
A1-02,E1-
03,O2-
0.0~590.0 0.0~400.0
09,E5-01
Depend
A1-02,E1-
0.0~590.0 0.0~400.0 03,O2-09
Depend
2~120 2~48 4
Base Unit
V1000
DEC
0
DEC Hz
0.0
DEC Hz
0.0
DEC
0
A1-02
DEC sec
Depend
A1-02
DEC sec
Depend
DEC Hz
0.0
O1-
DEC
0.00
03
DEC Hz
0.0
DEC Hz
1.0
A1-02,E1-
O1-
03,O2-
DEC
09,E5-01
04
Depend
A1-02,E1-
O1-
03,O2-
DEC
09,E5-01 04
Depend
A1-02,E1-
O1-
DEC
03,O2-09
04
Depend
A1-02,E1-
O1-
03,O2-
DEC
09,E5-01 04
Depend
A1-02,E1-
O1-
DEC
03,O2-09
04
Depend
DEC
4