Major Components And Accessories; Technical Specifications - Zip HydroTap G4 Installation Instructions Manual

Parts supplied
Command-Centre
QUICK START GUIDE STEP 1-
Prepare and fit the Taps
Note: This quick start guide must be read in conjunction with HydroTap Tap All-In-One Tap
the main installation and user instructions (If required)
• Before proceeding, read the installation and user instructions
• Check all the components are present and correct. For AIO mains and vented Taps
Cut a 50mm hole in the bench / sink top.
• Check that you have all the necessary tools
• Ensure the underbench can support the product weight when full of water,
(Check the specifications in the main book and allow an extra 5-8kg when full. ) Black plastic
SINK TOP
spacer
Before installing ensure the following have been provided at 50mm
the installation site: ALL THREAD
Stainless
• Sufficient space in the cupboard to install all of the undersink units in accordance ROD
washer NOTE: make sure the tap location will allow the nozzle to drain into the sink.
with these Installation Instructions. Refer to technical specification for dimensions. If
required, make allowance for a booster heater. (Refer to the main book, for detailed SPIDER
installation instructions). Fit the CLAMP
• BLACK STAINLESS STAINLESS STEEL
A potable water supply connection with isolating valve inside the cupboard within PLASTIC STEEL WASHER,
reach of the flexible braided hose and positioned so that the connection point and the SPACER WASHER 6mm
stop cock will not be obstructed when all the undersink units are installed. SPIDER CLAMP, NUT
• For Zip HydroTap 160/125 &160/175 models, a 220-240Vac, 10A GPO will be AND 6mm NUT.
SPIDER
required. For Zip HydroTap 240/175 models, two 220-240Vac, 10A GPOs will be CLAMP
required. (One GPO is for the Zip HydroTap and the other for the Booster heater). NOTE: feed each of the three tubes and
NOTE: Check the cable lengths and outlet positions before proceeding. electrical cable evenly in between the legs of O-RING
NUT the SPIDER CLAMP when installing.
• A potable cold water supply with a minimum working pressure of 172kPa and a
maximum working pressure of 700kPa connected via an isolation valve. 35mm dia hole
BASE
• For the mains pressure All-IN-ONE, both a hot and cold water supply will be required. Hole positioning: Position the tap such that it dispenses into BLOCK ALL
• The undersink appliances must be mounted in upright positions as shown in the the sink bowl with ample clearance for a cup or tea pot. Alternatively, SPIDER THREAD
diagrams. O-RING
the tap could be mounted away from the sink using a Zip Font, avail- Sink ROD SINK TOP
able as an accessory. BASE
IMPORTANT! BLOCK
Do not proceed with the installation if these NUT
requirements are not met. Apply a light smearing of silicon sealant USB
on the underside of the upper spacer to CABLE
ensure a watertight fi t.
Parts Supplied Description Parts Supplied Description
Mixer Tap Fit the O-ring to the underside of the AIO tap
Duct kit 4-in-1 (If required) then pass all hoses through the 50mm hole.
1 off
Hydrotap Tap 1x Air Duct
1 x Mounting
and hoses plate
Tap
Vent kit
O ring Base
1 off UPPER
1 x Kickboard UPPER RUB-
Undersink Unit RUBBER BER WASHER
with air and water- louvre WASHER Chiller
1 x Door vent Clear tube to Vent connection
filter louvre BLUE
LOWER RUBBER NOTE: feed each of
1 x front vent grill WASHER LOWER RUB-
the tubes and elec- Boiler
BER WASHER trical cable evenly in connection
1 off WASHER WASHER between the legs of RED
1 x Restrictaflow HydroTap
the BASE BLOCK
valve and Tee Booster heater NUT SPIDER.
piece for Mixer and hoses NUT BRAIDED
Taps (Supplied with HOSE x 3
White Hose White ring Blue ring on
240/175 models) Ext. Mains on LHS to RHS mains IN to
For HydroTap and Mixer taps
cut a 35mm hole in the bench / sink top. Mains in Mixer IN
Blue band
1 off Mains water BENCH TOP
connection hose Mixer IN From Mixer OUT to Tap - Vented version only
Ø35mm Red band
Mixer Out
801600 - Zip Quick Start Guide - October 2013 - V1.06
Commercial Chilled HydroTap
HydroTap s
®
Specifications
Capacity 13A Socket
Chilled Required
(200ml
glasses/hr)
Chilled only
175 1x13A
** Add an extra 3-4kg when full of water.
Page 8 of 16

Major components and accessories

Description
Tap options*
1 x HydroTap
Classic
Elite or Arc / Cube
#
(inc. Tube kit)
#
and components
TM
1 x
Command-Centre
with air and water
filters
1 x Mains water
connection hose
Duct kit
1 x Exhaust duct
1 x Mounting plate
2 x Outlet vent
1 x Inlet vent
1 x User guide and
ZIP HydroTap
®
User Guide
Tap Operation...................(Pages 2-5)
• 1 x Quick start
LCD Screen & Menu .......(Pages 6-18)
•
• Maintenance.................... (Pages 18-20)
• Date of Installation.........
BC160/125G4
BC240/175G4
BCH160/125G4
BCH240/175G4
AV160/125G4
AN160/125G4
AV240/175G4
AN240/175G4 guide
1 x Installation
Affix Model Number Label
Here
801599
instruction
801599 - HydroTap User Guide - Nov 2013 UK - V1.05 Page 1 of 20

Technical specifications

®
Power
Rating
(kW @230V)
0.30
801525UK G4 Commercial chilled only installation instructions - June 2016 - V2.04
Accessories
G4
®
TM
** Chrome finish part numbers are shown,
alternative finishes are available.
* Finish dependant upon model purchased.
G4 range
Chilled and filtered.
Unit Dimensions
W x D x H (mm) Weight
With exhaust duct
336 x 480 x 335
Description
Font Arc / Cube
93441UK**
Font Classic / Elite
90915UK**
Replacement
internal 0.2 micron
ZT402
Disabled lever kit
SP91563
Recommended
water block
HE45004
**Dry
(Kg)
24
filter