Xs770A Sensor Setting - YOKOGAWA Sushi Sensor XS770A User Manual

5.2

XS770A Sensor Setting

Specify sensor tag name, sampling data, sending period and transmission mode for XS770A.
Possible and the default value of each item is shown below.
Table 5-1
Item
Sensor Tag Name
General Sending Period
Setting
Sampling
Data
Transmission
Mode
Axis
More... Adjustment
Sub-band Setting
Unit Setting*
*1: When the Sushi Sensor firmware's regional parameter is other than US, the units used are as follows.
• acceleration : m/s
• velocity : mm/s
• temperature : °C
Table 5-2
Transmission mode
High Speed mode is ON
High Speed mode is OFF
If you operate a Sushi sensor at a sending period 4 hours or less, set High Speed mode is ON.
Table 5-3
Sub-band Setting Parameter
1
2
3
4
5
6
7
8
*1: If you select "All" as the sub-band setting, it takes a long time to complete the network join sequence of Sushi sensor.
XS770A Sensor Setting Items
This is the tag name of Sushi Sensor. Setting this
item is mandatory.
This is the sending cycle of sampling data.
This sets Z-axis and temperature data are sent or
Z-axis &
not. Number of axes to be sent is 1 because these
temp
data are put in one packet. (Refer to Section 7.1)
This sets the composite value of XYZ-axis and
XYZ-axis & temperature data are sent or not. Number of axes
temp to be sent is 1 because these data are put in one
packet. (Refer to Section 7.2)
This sets X-axis data are sent or not. For the
X-axis
packet format, refer to Section 7.3.
This sets Y-axis data are sent or not. For the
Y-axis
packet format, refer to Section 7.4.
For details of this setting, refer to Table 5-2.This
High Speed
setting is displayed in the Sushi Sensor App if the
Mode
Sushi Sensor firmware's regional parameter is EU.
XY Angle This specifies the angle of the axis adjustment.
Specify the frequency band to be used when
sending Sushi Sensor to LoRa Gateway. Set the
same parameter as LoRa Gateway. For details of
this setting, refer to Table 5-3.
This setting is displayed in the Sushi Sensor App
if the Sushi Sensor firmware's regional parameter
is US.
Acceleration
Select the acceleration, velocity, and temperature
Unit
unit to be displayed on the Sushi Sensor App.
1 Velocity Unit This setting is displayed in the Sushi Sensor App
if the Sushi Sensor firmware's regional parameter
Temperature
is US.
Unit
2
Transmission mode
The sending period can be set from 1 minute to 72 hours. However, if number of
axes to be sent is multiple, please set the transmission cycle to 10 minutes or more.
The sending period can be set from 4 hours to 72 hours. There is no limit on the
sending period depending on number of axes to be sent.
Sub-band Setting Parameters
Frequency [MHz]
All* 902.3-903.7
903.9-905.3
905.5-906.9
907.1-908.5
908.7-910.1
910.3-911.7
911.9-913.3
913.5-914.9
<5. XS770A Setting>
Description
blank
2[Hours]
ON
OFF
OFF
OFF
ON
0
1
g
in/s
°F
Description
Default Possible Setting
-
1,10,30[Minutes]
1,2,3,4,5,6,12,18,24,48,72[Hours]
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
5 degrees increments in the range
of -180 to 180 degrees
All, 1, 2, 3, 4, 5, 6, 7, 8
m/s , g
2
mm/s, in/s
°C, °F
IM 01W06E01-11EN
16