Cisco ONS 15454 ETSI Manual page 56

NTP- G23 Install Alarm Wires on the Backplane (ANSI Only)
Figure 1-24
Field
BITS
LAN
ENVIR
ALARMS
IN
Cisco ONS 15454 DWDM Procedure Guide, R8.0
1-56
Cisco ONS 15454 Backplane Pinouts (Release 3.4 or Later)
A B A B A B
1 1 1 1
2 2 2 2
3 3 3 3
4 4 4 4
BITS LAN
IN
FG1 FG2 FG3 FG4
Pin Function
A1 BITS Output 2 negative (–)
B1 BITS Output 2 positive (+)
A2 BITS Input 2 negative (–)
B2 BITS Input 2 positive (+)
A3 BITS Output 1 negative (–)
B3 BITS Output 1 positive (+)
A4 BITS Input 1 negative (–)
B4 BITS Input 1 positive (+)
Connecting to a hub, or switch
RJ-45 pin 6 RX–
A1
RJ-45 pin 3 RX+
B1
RJ-45 pin 2 TX–
A2
B2
RJ-45 pin 1 TX+
Connecting to a PC/Workstation or router
A1
RJ-45 pin 2 RX–
RJ-45 pin 1 RX+
B1
A2 RJ-45 pin 6 TX–
RJ-45 pin 3 TX+
B2
A1
Alarm input pair number 1: Reports
closure on connected wires.
B1
A2
Alarm input pair number 2: Reports
closure on connected wires.
B2
A3
Alarm input pair number 3: Reports
closure on connected wires.
B3
A4 Alarm input pair number 4: Reports
closure on connected wires.
B4
A5
Alarm input pair number 5: Reports
closure on connected wires.
B5
A6 Alarm input pair number 6: Reports
closure on connected wires.
B6
A7 Alarm input pair number 7: Reports
closure on connected wires.
B7
A8
Alarm input pair number 8: Reports
closure on connected wires.
B8
A9 Alarm input pair number 9: Reports
closure on connected wires.
B9
A10 Alarm input pair number 10: Reports
closure on connected wires.
B10
A11
Alarm input pair number 11: Reports
closure on connected wires.
B11
A12 Alarm input pair number 12: Reports
closure on connected wires.
B12
A B A B A B
7 1
ACO
8 2
5 9 3
6 10 4
ENVIRONMENTAL ALARMS
IN
IN/OUT IN
FG5 FG6 FG7
Field Pin
ENVIR A1/A13 Normally open output pair number 1
ALARMS
B1/B13
IN/OUT
A2/A14 Normally open output pair number 2
B2/B14
N/O
A3/A15 Normally open output pair number 3
B3/B15
A4/A16 Normally open output pair number 4
B4/B16
ACO A1 Normally open ACO pair
B1
CRAFT A1 Receive (PC pin #2)
A2 Transmit (PC pin #3)
A3 Ground (PC pin #5)
A4 DTR (PC pin #4)
A1 Alarm output pair number 1: Remote
LOCAL
audible alarm.
ALARMS
B1
AUD
A2 Alarm output pair number 2: Critical
(Audible)
audible alarm.
B2
N/O
A3 Alarm output pair number 3: Major
audible alarm.
B3
A4 Alarm output pair number 4: Minor
audible alarm.
B4
A1 Alarm output pair number 1: Remote
LOCAL
visual alarm.
ALARMS
B1
VIS
A2 Alarm output pair number 2: Critical
(Visual)
visual alarm.
B2
N/O
A3 Alarm output pair number 3: Major
visual alarm.
B3
A4 Alarm output pair number 4: Minor
visual alarm.
B4
Chapter 1 Install the Shelf and Common Control Cards
A B A A B A
1 1 1
2 2 2
3 3 3
4 4 4
MODEM CRAFT LOCAL ALARMS
VIS AUD
FG8 FG9 FG10
Function
If you are using an
AIC-I card, contacts
provisioned as OUT
are 1-4. Contacts
provisioned as IN
are 13-16.
B A B
11
12
IN
FG11 FG12
78-17704-02