Product Description And Intended Use - Nice Era Fit Series Instructions And Warnings For Installation And Use

ENGLISH
Complete Manual
Note for reading this Manual – Some of the figures referred to in the text appear
at the end of the manual.
1
WARNINGS AND GENERAL PRECAUTIONS
FOR SAFETY
•
•
Therefore, read this manual carefully before beginning work.
1.1 - Installation warnings
•
must be carried out exclusively by a skilled and qualified technician, in observance
of local laws, standards, regulations and the instructions in this manual.
•
for automating your awning (or shutter). If not suitable, do NOT proceed with instal-
lation.
•
automation mechanism disconnected from the power mains. Moreover, before
".
•
deactivate all mechanisms not needed for motorised operation of the awning (or
shutter).
•
other supporting surface, you must protect moving parts with a cover to prevent
accidental access. Refer to the awning (or shutter) instruction manual for informa-
tion on how to provide protection; in any case, make sure access is possible for
maintenance work.
•
ping or contact with liquids of any type; do not drill or apply screws to the exterior;
never place the product near sources of heat or expose to naked flames (fig. 1).
situations. In these cases, suspend installation immediately and contact the Nice
Service Centre.
•
tor internally. Such screws could damage the motor.
•
manual.
•
manual. The manufacturer declines all liability for damage caused by makeshift
modifications to the product.
•
length of the power supply cord with a tube that is indicated for protecting electri-
cal cords.
•
used because the cable cannot be substituted and the damage could become a
source of danger. In these cases, contact the Nice Service Centre.
•
when it is moving.
1.2 - Use warnings
•
physical, sensorial or mental capacities are reduced, or who lack the necessary ex-
perience or skill, unless suitable instructions on how to use the product have been
given through the mediation of a person who is responsible for their safety, moni-
toring and the instructions on how to use the product.
•
vices out of reach of children.
•
ple at a safe distance until the movement has been completed.
•
starting such jobs.
•
.
or repaired; contact specialised technical personnel to solve these problems.
.
.
.
.
2
PRODUCT DESCRIPTION AND
INTENDED USE
Era Fit is a family of tubular motors intended exclusively for the automation of vari-
ous types of awnings and shutters.
manufacturer is not liable for damage resulting from any use of the product
other than the intended use specified in this manual.
Functional characteristics of the product:
•
•
inside of the box with screws and the appropriate support brackets (not included
in the package);
•
tronically controls the movement and precision of the limit switches;
•
mate sensors) that use the NRC radio system;
•
package (see fig. 3);
•
•
lower limit switch or various intermediate positions;
•
caused by overuse of the automation (beyond the indicated limits), automatically
cuts off the electricity supply, restoring it as soon as the temperature goes back to
normal;
•
3
INSTALLATION OF THE MOTOR AND
THE ACCESSORIES
3.1 - Preliminary checks before installation and lim-
itations on use
•
•
Each version is designed to drive awnings/shutters of a certain size and weight.
Therefore, before installation make sure the product's motor torque, rotation
-
speed and operation time are suitable for automating your awning or shutter (see
"
com). In particular, do not install the product if its motor torque is greater
than that needed to move your awning or shutter.
•
motor torque, as follows:
-
– for motors that are size "S" (Ø = 35 mm), the minimum inside diameter of the
winding roller must be 40 mm;
– for motors that are size "M" (Ø = 45 mm) and have a torque of up to 35 Nm (in-
cluded), the minimum inside diameter of the winding roller must be 52 mm;
– for motors that are size "M" (Ø = 45 mm) and have a torque of up to 35 Nm (in-
cluded), the minimum inside diameter of the winding roller must be 60 mm.
– for motors that are size "L" (Ø = 58 mm), the minimum inside diameter of the
winding roller must be 70 mm.
•
front of it for it to be completely opened.
•
agents must be guaranteed.
characteristics" section.
3.2 - Assembly and installation of the tubular motor
and 3.1. Incorrect installation could cause severe physical injury.
To assemble and install the motor, refer to fig. 4. Moreover, consult the Nice prod-
uct catalogue or go to www.niceforyou.com to choose the crown of the limit switch
(fig. 4-a), the drag wheel (fig. 4-b) and the motor fastening bracket (fig. 4-f).
-
3.3 - Installation of accessories (optional)
-
those that are compatible and choose the models desired, see the Nice product cat-
. .
alogue, also viewable at www.niceforyou.com. Fig. 3 shows the type of accessories
that are compatible and their connection to the motor (all of these are options and
not included in the package).
.
.
.
.
.
English – 2
-
-
.
.