Safety Warnings And Precautions; Product Description And Intended Use - Nice Era Zero Instructions And Warnings For Installation And Use

ENGLISH
1
SAFETY WARNINGS AND
PRECAUTIONS
1.1 - Safety warnings
• CAUTION! – Follow these personal safety instruc-
tions very carefully. Incorrect installation could cause
serious physical injury. Therefore, before starting work
carefully read all parts of the manual and if in any doubt
contact the Nice Service Centre for clarifications.
• CAUTION! – Important safety instructions; save
the s e instructions for future use. Keep this manual
in a safe place to enable future product maintenance and
disposal procedures.
1.2 - Installation warnings
• All product installation, connection, programming
and maintenance operations must be performed
exclusively by a qualified and skilled technician, in
observance of laws, standards and local regula-
tions and the instructions in this manual.
• Before installation, ensure that this specific product is
suitable for the automation of your shutter (see chapter 3).
• All product installation and maintenance operations must
be performed with the automation disconnected from the
power mains. As a precaution, affix a notice with the text
"WARNING: MAINTENANCE IN PROGRESS" on the dis-
connect device.
• Before starting installation procedures, move away all
electric cables not involved in the work and deactivate all
mechanisms not required for motor-driven operation of
the shutter.
• If the product is installed at a height of less than 2.5 m
from the floor or other support surface, the moving parts
1 – English
must be protected with a suitable covering, to avoid in-
advertent access. For protection, refer to the instruction
manual of the shutter, ensuring that future access for
maintenance purposes is guaranteed.
• On sun awnings, a minimum horizontal distance of 40
cm must be guaranteed between the awning completely
open and any fixed object positioned in front.
• During installation, handle the product with care, avoid-
ing the risk of crushing, impact, dropping or contact with
any type of liquid, do not insert sharp objects in the mo-
tor, do not drill or insert screws on the motor exterior and
do not place the product in the vicinity of heat sources or
naked flames (fig. 2).
This may damage product and cause malfunctions, fire
or hazardous situations. If this occurs, suspend installa-
tion immediately and contact the Nice Technical Assis-
tance.
• Do not disassemble the product in excess of the opera-
tions envisaged in this manual.
• Never make any modifications to part of the product oth-
er than those specified in this manual. Operations other
than as specified can only cause malfunctions. The man-
ufacturer declines all liability for damage caused by ma-
keshift modifications to the product.
• The product power cable is in PVC; this makes it suitable
for installation exclusively indoors. If installed outdoors,
the cable must be covered with a protection ducting.
• The unit's power cable may not be replaced. If the cable
is damaged, the device must be scrapped.
• Do not use multiple control devices for a single tubular
motor or a single control device for multiple tubular mo-
tors (fig. 3). If necessary, use the special Nice accessory
"TTE".
• During system set-up, keep all persons far from the shut-
ter when moving.
• To control the product, use exclusively hold-to-run type
pushbuttons, i.e. which must remain pressed for the en-
tire manoeuvre.
• The product packaging material must be disposed of
in full observance of current local legislation governing
waste disposal.
1.3 - Operation warnings
• The product should not be used by children or people
with impaired physical, sensorial or mental capacities.
• Do not allow children to play with fixed control devices.
• Take care in the vicinity of the shutter / awning / screen
when moving, and keep at a safe distance until the ma-
noeuvre is completed.
• For model E MH / E LH – When performing the manual
operation, take great care if the shutter is raised because
it is liable to fall rapidly in the event of weak or broken
springs.
• When cleaning windows in the vicinity of the automation,
do not activate any control devices and if the latter are
automatic, disconnect the power supply.
• Frequently check the automation, to detect for imbal-
ance, any signs of wear or damage to cables or springs
(if present). Do not use the automation if adjustments or
repairs are required. In this case always contact a spe-
cialised technician to solve the problem.
2
PRODUCT DESCRIPTION AND
INTENDED USE
This product is a tubular motor designed for the automa-
tion of a shutter, sun awning or solar screen. Any other
use is strictly prohibited! The manufacturer declines
all liability for damage resulting from improper use
of the product and other than as specified in this
manual.
The product has the following features:
- powered via the electrical mains at 230 V;
- designed to move the shutter in Ascent and Descent
by means of wall-mounted pushbuttons (not supplied in
pack); the model E MH / E LH is also equipped with a
mechanism for emergency manual manoeuvres, for use
in the event of a power failure;
- is equipped with an electromechanical system that auto-
matically shuts off power supply when the shutter reach-
es the set limit positions (fig. 4): position "0" (shutter to-
tally retracted) and position "1" (shutter totally extended);
- the entire tubular motor is installed inside the shutter roll-
er and the external face of this product can be mounted
directly alongside the casing or by means of the relative
support brackets (not supplied in pack);
- it is designed for residential use, i.e. discontinuous.
It guarantees a continuous operating time of maximum 4
minutes;
- it is fitted with a thermal cut-out which in the event of
overheating due to use of the automation in excess of the