Reference - Aiwa LCX-MT22 Operating Instructions Manual

REFERENCE

Care and maintenance
Occasional care and maintenance of the unit and the software
are needed to optimize the performance of your unit.
To clean the cabinet
Use a soft and dry cloth. If the unit's surfaces are extremely
dirty, use a soft cloth lightly moistened with mild detergent
En
solution. Do not use strong solvents such as alcohol, benzine
or thinner.
To clean the tape heads
Dirty tape heads cause sound deterioration. After every 10
hours of use, clean the tape heads with a head cleaning
cassette. Refer to the instructions of the cleaning cassette.
To demagnetize the tape heads
Use a demagnetizing cassette after every 20 to 30 hours of
use. Refer to the instructions of the demagnetizing cassette.
Care of CDs
When a CD becomes dirty, wipe it from the center out with a
cleaning cloth. After playing a CD, store it in its case. Do not
keep it in hot or humid places.
Care of tapes
Store tapes in their cases after use. Do not leave tapes near
magnets, motors, television sets, or any source of magnetism.
Do not expose tapes to direct sunlight, or leave them in a car
parked in direct sunlight.
Care of MDs
Keep a cartridge in the attached case. Do not open the shutter
of the cartridge to touch the disc directly. If the disc inside
becomes soiled, it is very difficult to clean. The cartridge can
also be damaged. Close the shutter if it opens while handling
or ejecting a disc. Otherwise dust may enter or a disc may
become scratched.
42
MD guide messages
Blank Disc
Nothing is recorded on the disc.
Can't Edit
•Editing is attempted while in programmed play.
•Tracks are too short to be joined.
•The combine function was used while playing back the first
track.
•The divide function was used at the beginning of the track.
•The combine function was used to join tracks recorded in
different modes.
•While entering a title during recording, the number of entered
characters reaches the upper limit.
•Combining all "solo" groups is attempted although there is
only one solo group.
Can't COPY
Recording is not possible due to the SCMS (23 page).
Protected
The disc is record-protected. Slide the record-protect tab on
the disc (see page 19).
Disc Error
•The disc is damaged by scratches. Replace the disc.
•The unit received a strong shock during TOC reading. Do
not subject the unit to strong shock during TOC reading.
Disc Full
There is not enough time remaining on the disc to record.
Replace the disc with another recordable disc.
Temp Over
•The temperature of the unit is too high. Leave the unit in a
cool place for a while before operating it again.
•The surrounding temperature is too high or too low. Operate
the unit at moderate room temperature.
PB Disc
There is an attempt to record or edit a prerecorded music disc.
Replace the disc with a recordable one.
Toc Full
There are too many tracks or emphasis data to be recorded or
edited, or there is no room on the disc. Erase tracks to reduce
tracks.
Mecha Error
Error occurs in the loading mechanism. (All functions
concerning to MD will be disabled)
Turn the power off and disconnect the AC cord, and turn the
unit on again. If this message still appears, consult your local
AIWA dealer.
MD ERROR
Trouble occurs in the MD unit. Consult your AIWA dealer.
MD No Disc
There is no MD inserted in the unit. Insert an MD.
Emergency
Recording is not possible due to a scratched disc or a strong
shock. Replace the disc.
UTOC Error
Error occurs due to a strong shock during recording, TOC
edit or TOC reading. Replace the disc. However, erasing all
tracks on a disc can only be done.
LONG CD
The playing time of CD to record is longer than the recordable
remaining time of MD. (see page 21)
WAIT XXmin (XX=number of minutes)
Double speed recording is prohibited within the last 74
minutes. Wait for the displayed number of minutes or record
at normal speed (see page 21).
Can't RECOPRGM ERROR
Double speed recording is attempted while the same track is
programmed twice or more.
Can't RECOMONO
Digital recording is attempted while selecting the monaural
recording mode.