Page 1
BASIC MD MECHANISM : AZG-4 A MODEL CODE : 8ACJB-0130(S) 8ACJB-0140(D) 8ACJB-0180(L) REMOTE SYSTEM SPEAKER CONTROLLER LCX-MD211 SX-MD210 RC-AAT11 This Service Manual is the Revision Publishing and replaces Simple Manual LCX-MD210(D), LCX-MD211(EZ),(S/M Code No. 09-003-429-4T2). u163 S/M Code No. 09-007-429-4R2 http://www.xiaoyu163.com...
Page 2
http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 MAIN UNIT Compact disc player section FM tuner section Laser Semiconductor laser (l = 780nm) D-A converter 1 bit linear Tuning range 87.5 MHz to 108 MHz Wow and flutter Unmeasureable Antenna terminals 75 ohms (unbalanced) MD recorder section MW tuner section...
Page 3
http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING 3 7 63 1515 0 CAUTION This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
Page 4
http://www.xiaoyu163.com DISASSEMBLY INSTRUCTION 1. Removing CD Mechanism, CHAS, CD 3 7 63 1515 0 1-1. Remove 12 screws (BVT2+3-10). Pull the panel, L in the rear direction, and press it in the bottom direction to remove it. 1-2. Remove the panel, R in the same way as for L. L 13942296513 1-3.
Page 5
http://www.xiaoyu163.com 1-4. Release the tabs on both sides at the top of front 3 7 63 1515 0 cabinet, and lift the rear of CHAS, CD to remove the CHAS, CD, CD mechanism and CD C.B. in one unit. L 13942296513 2.
Page 6
http://www.xiaoyu163.com 2-2. Remove two screws (BVT2+3-10) that fix the 3 7 63 1515 0 CHAS, MD to the CHAS, MAIN. 2-3. Remove two QT2+3-8 screws at the bottom L 13942296513 of both sides of front cabinet. Remove two BVT2+3-10 screws from the bottom of CHAS, MAIN.
Page 7
http://www.xiaoyu163.com 2-4. Release the tabs of front cabinet, and remove the 3 7 63 1515 0 CHAS, MAIN with the power transformer C.B. 2-5. Remove two screws (BVT2+3-10) that fix the CHAS, MD to the front cabinet. Disconnect the flat cables (14P, 18P) from the MD L 13942296513 mechanism, and remove the sheets that hold the cables.
Page 8
http://www.xiaoyu163.com ELECTRICAL MAIN PARTS LIST 3 7 63 1515 0 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C204 87-010-197-080 CAP, CHIP 0.01 DM C225 87-010-401-080 CAP, ELECT 1-50V 87-A20-459-010 C-IC,LC78622ED C226 87-010-401-080 CAP, ELECT 1-50V 87-A21-213-010 IC,BA17808T C227...
Page 25
http://www.xiaoyu163.com TAPE MECHANISM PARTS LIST 1 / 1 3 7 63 1515 0 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 1 S1-921-030-4A0 HEAD BASE 36 S1-921-140-220 REC BUTTON LEVER 2 S1-821-030-070 AZIMUTH SPRING 37 S1-921-140-170 P.S.LEVER SPRING 3 S1-921-030-090 PANEL P SPRING...
Page 26
http://www.xiaoyu163.com CD MECHANISM EXPLODED VIEW 1 / 1 3 7 63 1515 0 SHAFT,SLIDE SF-P101NR CHASSIS L 13942296513 SPINDLE MOTOR C,B MOTOR(M1) CD MECHANISM PARTS LIST 1 / 1 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION 1 S2-121-A28-400 COVER GEAR...
Page 28
http://www.xiaoyu163.com TEST MODE CD TEST MODE 3 7 63 1515 0 1-1 How to activate CD Test Mode Insert the AC plug while pressing the "CD function" button. Test mode will be activated and [CD TEST] will be appeared in the LCD display. Note: Test mode can not be activated when CD door switch is opened.
Page 29
http://www.xiaoyu163.com MD TEST MODE 3 7 63 1515 0 1-1 How to start up MD Test Mode Insert the AC plug while pressing the "MD function" button. After the MD test mode has started up, [MD TEST] message appears and the test mode becomes operatable. Note: •...
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 2) Press "s" button to display [ALL SVOFF] after checking • Checking the focus search and spendle kick 2 1) When "TUNER function" button is pressed in the "ALL SVOFF" state regardless disc existence, focus search and spindle kick are executed continuously.
Page 32
http://www.xiaoyu163.com <CD> 3 7 63 1515 0 CD C.B CN401 SFR430 IC404 (VREF) CN405 C431 TP(TE) R405 TP(RFSM) IC402 IC401 CN403 Note: • Connect a provbe (10 : 1) of the oscilloscope to adjust. 2. Tracking Balance Adjustment • Connect negative side of the oscilloscope to TP (VREF) for L 13942296513 Oscilloscope each adjustment.
Page 33
http://www.xiaoyu163.com <MD> • Perform 1~3 adjustment when display showing [NO ADJUST]. 3 7 63 1515 0 1. Temperature Compensation Adjustment Then, confirm the values of [I ** E ] in the display are • Test point: Check on the display. within the following range.
Page 34
http://www.xiaoyu163.com 3 7 63 1515 0 12) Press "s" button to display [ALL SVOFF]. 6. UTOC Erase To be performed only when erasure is needed with disc that have already been recorded upon. 1) Insert the disc that is to be used to erase the UTOC. 2) Move the pickup to the center track using "g"...
Page 35
http://www.xiaoyu163.com SERVICE JIG AND TOOLS Service jigs and tools for repairing as follows; 3 7 63 1515 0 Usage Parts Name Parts No CD mecha stand JIG, P-CD BY TORIKOSHI SV-J00-018-010 PU extention FFC FFC-CABLE, 16P 1.0 250mm 87-CE1-640-010 S.T.I. G-98-50 FFC, 8P-1.0 SV-J00-043-010 SV-J00-044-010...
Page 37
http://www.xiaoyu163.com IC DESCRIPTION IC, LC877264A-EZ 3 7 63 1515 0 Pin No. Pin Name Description O-ARDY Output ready signal for MD micro controller communication. L: Enable. O-SREQ Request system micro controller output for MD micro controller communication. L: Enable. O-SOUT Output serial data for MD micro controller communication.
Page 38
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description I-DOOR Detect CD door. H: OPEN, L: CLOSE. I-WRQ Sub code Q read standby for CD LSI communication. I-DRF Input RF level detection. COM0 Output COM1. COM1 Output COM2. COM2 Output COM3.
Page 39
http://www.xiaoyu163.com IC, LA9241ML 3 7 63 1515 0 Pin No. Pin Name Description Connect to the pickup's photo diode; adding this pin to pin FIN1 generates RF signal, FIN2 and subtracting it generates FE signal. FIN1 Connect to the pickup's photo diode. Connect to the pickup's photo diode;...
Page 40
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description CV– Input for CLV error signal from DSP. RFSM Output for RF. RFS– For setting RF gain and 3T compensation constant together with RFSM. SLICE LEVEL CONTROL; output for controlling the data slice level of DSP with RF waveform.
Page 41
http://www.xiaoyu163.com IC, LC78622ED 3 7 63 1515 0 Pin No. Pin Name Description DEFI Defect detection signal (DEF) input. Test input. A pull-down resistor is built in. (Must be connected to 0V) External VCO control phase comparator output. VVSS – Internal VCO ground.
Page 42
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description RVSS – Right channel one-bit DAC R channel ground. (Must be connected to 0V) RCHO Right channel one-bit DAC R channel output. RVDD – Right channel one-bit DAC R channel power supply. MUTER Right channel one-bit DAC R channel mute ouput.
Page 43
http://www.xiaoyu163.com IC, LC72131D 3 7 63 1515 0 Pin No. Pin Name Description X IN A crystal oscillator (4.5MHz) is connected to X OUT pin. – Not connected. To enable the IC. Active "H". Digital data input from CPU (LC877264A-EZ) when relevant key is operated. Active "H".
Page 44
http://www.xiaoyu163.com IC BLOCK DIAGRAM 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 - 44 - http://www.xiaoyu163.com...
Page 45
http://www.xiaoyu163.com 3 7 6 3 1 5 1 5 0 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 - 45 - http://www.xiaoyu163.com...
Page 46
http://www.xiaoyu163.com VOLTAGE CHART < CD > Test condition : CD play 3 7 63 1515 0 IC401(LA9241ML) IC402(LC78622ED) L 13942296513 u163 46 http://www.xiaoyu163.com...
Page 47
http://www.xiaoyu163.com < CD > < TUNER > Test condition : Tuner function 3 7 63 1515 0 IC403(LA6541D) IC721(LC72131D) IC771(LA1837N) L 13942296513 Q771(2SA952) Q773(DTC114Y) u163 47 http://www.xiaoyu163.com...
Need help?
Do you have a question about the LCX-MD211 and is the answer not in the manual?
Questions and answers