Samsung LH008IWJ Series Installation Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. LH008IWJ Series
  6. Installation manual
Samsung LH008IWJ Series Installation Manual

Samsung LH008IWJ Series Installation Manual

Hide thumbs Also See for LH008IWJ Series:
Table of Contents

Advertisement

Quick Links

Samsung Electronics
LED Display
Installation Manual
LH008IWJ*** (P0.84)
LH012IWJ*** (P1.26)
LH016IWJ*** (P1.68)
SNOW-1810U
Ver. 2.0
(2020.03.20)

Advertisement

Table of Contents
loading

Related Manuals for Samsung LH008IWJ Series

Summary of Contents for Samsung LH008IWJ Series

  • Page 1 Samsung Electronics LED Display Installation Manual LH008IWJ*** (P0.84) LH012IWJ*** (P1.26) LH016IWJ*** (P1.68) SNOW-1810U Ver. 2.0 (2020.03.20)
  • Page 2 Revision History Samsung Electronics Version Date (Y/M/D) Description 2020/03/20 New Release...
  • Page 3 ∙ Case when period between unpacking and turning on the power of products is spent more than 7days, even though it is under Samsung recommended storage condition. ∙ Case when production date on the label is exceed more than 6 months, even though vacuum packaging is no problem.
  • Page 4 Dehumidification guidance – during operation Samsung Electronics  Electrical short in package is possible to happen during products are working.  For keeping quality of products during installation, please refer below cautions. - If one of below case meet during operation, MUST do dehumidification process.
  • Page 5 Dew condensation due to overcooling Samsung Electronics  Even though meet with Samsung recommended operation condition, dew condensation is possible to happen when surface of products is colder than environment temperature or hot & humid air blow to cooled surface of products.
  • Page 6 Guidance of latest firmware Samsung Electronics  When install products, please update latest firmware on online - You can download latest firmware from SLM site. ∙ URL of SLM Page : https://www.secslm.com ∙ After login  Help  Download Center에서 Download ∙...
  • Page 7 Check first before Installation (1/2) Samsung Electronics • All Power cables and OCM cable must be connected firmly • For HDBT signal stability, use the cable above CAT6 *STP, *FTP level. ( Length 15m~100m ) “CAT6 UTP can not be allowed”...
  • Page 8 Check first before Installation (2/2) Samsung Electronics • Install the device only using SNOW-1810U and its supplied IG. ※ Please check below Cabinet and S-box compatibility table information S-Box SNOW-1810U SNOW-1703ULD SNOW-1703U BN91-20525A BN91-19993A BN91-19100A Cabinet IF015H, IF015H, IF015H, IF020H,...

  • Page 9: Table Of Contents

    Table of Contents Samsung Electronics Product Information and Precautions for Installation ( 4 page ) Check Point about the Radiant Heat ( 9 page ) Preparation for Cabinet Installation ( 15 page ) Frame Installation ( 22 page ) Cabinet + Frame Installation ( 30 page ) 6.
  • Page 10 1. Product Information and Precautions for Installation Samsung Electronics ◇ Cabinet Infomation IW008J (P0.84) IW012J (P1.26) IW016J (P1.68) 0.84 mm 1.26 mm 1.68 mm Pitch Basic Spec. Cabinet Resolution 960 X 540 640 X 360 480 X 270 1600-nit/500-nit 1600-nit/800-nit...
  • Page 11 Samsung Electronics 1. Product Information and Precautions for Installation ◇ Screen configuration by model (Pitch) (Refer to page 22 for frame kit) Specification P0.84 P1.26 P1.68 Cabinet Size 806.4 x 453.6 x 72.2 806.4 x 453.6 x 72.2 806.4 x 453.6 x 72.8...

  • Page 12: Product Information And Precautions For Installation ( 4 Page )

    1. Product Information and Samsung Electronics Precautions for Installation • Precautions for Installation (LED damage) Caution Image [ Beware of Outside Impact, Fall] ① Beware not to cause any impact on the LED screen or drop the product on the floor MODULE after the protection gets taken off for installation.
  • Page 13 1. Product Information and Precautions for Installation Samsung Electronics ◇ Caution for cleaning screen ★Caution★ - Watch out for damage when cleaning gap between Half- Cabinets - Watch out for damage when cleaning gap between Modules - Do not insert any cleaning tool or spay cleaner directly into...
  • Page 14 1. Product Information and Precautions for Installation Samsung Electronics • Preparations for Installation • Provided in accessory kit. (CY-WJJPWP). PROTECTION EDGE PROTECTION V/H MAGNET JIG GAP-TOOL (BN81-17111A) (BN81-17514A/BN81-17515A) (BN81-17114A) (BN81-17113A) (-) (+) driver • Provided in Frame Kit. (BN96-48298A) M3, L6...

  • Page 15: Check Point About The Radiant Heat

     Standard and condition for indoor installation ※ Written under ‘Full white, (back light 7)’ standard Written under ‘Video, (back light 10)’ standard - Standard for using ‘SAMSUNG WALL MOUNT’ (Fulfill ADA) ※ ADA(American’s with Disabilities Act vibration - Ceiling installation, outdoor installation, cannot be installed where there is 98.6mm...
  • Page 16 2. Check Point about the Radiant Heat– without Fan Samsung Electronics ※ At least 60mm installation space required for upper,  Minimum spacing for buried installation lower, left, and right All interior finishes proceed after screen installation Recommended condition : Min 500mm (set ~ ceiling)
  • Page 17 2. Check Point about the Radiant Heat– without Fan Samsung Electronics  Minimum spacing for buried installation Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation...
  • Page 18 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and placement during landfill installation Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to...
  • Page 19 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and placement when installing walls Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to...
  • Page 20 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and placement during rear exhaust Recommended condition : Min 500mm (set ~ ceiling) Min 100mm when maintaining the indoor temperature below 25 degrees due to air conditioning operation The SCREEN wall is managed below 30 ℃...

  • Page 21: Preparation For Cabinet Installation

    3. Preparation for Cabinet Installation Samsung Electronics • Preparations Before Installation ① Remove the Box tape at the upper area and then open up the box. (Fig.2) ② Remove the Top–Cushion and hold the handle inside PE-Bag and pull out the set then remove PE bag.
  • Page 22 3. Preparation for Cabinet Installation Samsung Electronics ④ 18ea Holder-PCB fixing screws and 4 Cover-PCB fixing screws are released. ⑤ Remove the filament tape attached to the top / bottom / left / right. Fig.4 Holder-PCB & Cover-PCB & Protective Sheet Removal...
  • Page 23 3. Preparation for Cabinet Installation Samsung Electronics ⑥ Unfasten the 4 screws on the Cover Corner area to separate those screws and Remove the protective sheet attached to the two sides (Top/Bottom). (Fig.4) SCREW-MACHINE (6003-000133, M4L8) SCREW Fig.4 Cover Corner Removal...
  • Page 24 3. Preparation for Cabinet Installation Samsung Electronics - Using Spacer-PET ⑦ When Black Seam occurs, remove the Spacer-PET of the point. ※ Spacer-PET should not protrude more than module ⑧ If necessary, attach Spacer-PET. (Fig.5) ※ Check the gap between the module and the Bracket-Sub using a gap gauge.
  • Page 25 3. Preparation for Cabinet Installation Samsung Electronics ◈ Dehumidification ① In order to protect LED devices, the following items must be dehumidified. [Dehumidification when Installed] - If it is installed after more than 6 months in vacuum-packed condition after factory shipment.
  • Page 26 3. Preparation for Cabinet Installation Samsung Electronics ◈ Process of Dehumidification - The Dehumidification process progresses automatically for 24 hours as the brightness increases gradually. Step condition Brightness Time Lighting up display with 10 gray scale 2 hr Lighting up display with 20 gray scale...
  • Page 27 3. Preparation for Cabinet Installation Samsung Electronics ◈ Reference : Process of Screen check TOGGLE SWITCH SWITCH POWER INLET POWER OUTLET TOGGLE SWITCH 화면 검사 사진 확인 Check the picture of the screen ◈ Internal white pattern 1. After turn on power, press the toggle switch button for five seconds 2.

  • Page 28: Frame Installation

    4. Frame Installation Samsung Electronics ◇ Frame Kit Composition. ⓑ ⓒ ⓑ ⓐ VG-LFJ08SWW VG-LFJ08FWW VG-LFJ08TWW VG-LFJ08UWW Item Units Units Units Units ⓐ BRACKET H (horizontal) ⓑ BRACKET SIDE (vertical) ⓒ BRACKET MIDDLE (vertical) ⓓ JOINT H ⓔ JOINT V ⓓ...
  • Page 29 4. Frame Installation Samsung Electronics ① Assemble Bracket Side/Middle with Bracket H. - First insert ⓐBracket H to assembled Joint H and Bracket H. (Fig.1) - Second put 3 groups of Bracket H on ground. And insert Bracket Side/Middle to Bracket H. (Fig.2) .
  • Page 30 4. Frame Installation Samsung Electronics ② Assemble Leveler on the Bracket Side at required height position. - Put Leveler on Bracket side at required height position with moving up and down. (Fig.1) M4L8 Screw Fig.1 Assemble Leveler...
  • Page 31 4. Frame Installation Samsung Electronics ③ Install assembled Frame on the wall. - Place the assembled frame on the wall, align it with the desired height and level, and fasten one place at the top center. (Fig.1) - When attaching the frame to the wall, use the 6mm hexagonal wrench to correct the gap with the leveling bolt. (Fig.2 If the leveling bolt is not enough to attach to the wall, add Tape Wash to reinforce it.
  • Page 32 4. Frame Installation Samsung Electronics - When the leveling work is completed, additional frame and wall should be fastened according to the guide below. (Fig.3) - Fix the fastening position closest to the bracket side / lid among the fastening holes of the bracket H.
  • Page 33 4. Frame Installation Samsung Electronics ※ Precautions for Fastening the Screws...
  • Page 34 4. Frame Installation Samsung Electronics ※ Extent Frame Installation to Horizontal / Vertical. - Assemble Joint C / Joint V into second assembled Frame. M4L8 Fastening M4L8 Fastening <Horizontal Extension> <Vertical Extension> - Insert the second FRAME to first FRAME.
  • Page 35 4. Frame Installation Samsung Electronics ※ Frame extension in horizontal / vertical direction - The joints of the frames to be extended are inserted into the existing frames and the jig is inserted to correct position. - After the Jig fastening, fasten the screws between the frames..

  • Page 36: Cabinet + Frame Installation

    5. Cabinet + Frame Installation Samsung Electronics • Fix I/G Location Install I/G first on the back side of the Cabinet of each Type (Fig.1) ※ Installation location: Align the I / G to the point below 50 ~ 55mm on the right frame and fasten the screws. (Fig.2) ※...
  • Page 37 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation ① After installing Frame and I/G, install cabinets on the bottom line first ※ Cabinet installation should be performed from the bottom to the top, left end → right end or right end → left end direction. (Fig.1) ②...
  • Page 38 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation ③ After installing the I / G, install the cabinet from the end of the first floor. (Fig.3-1) ※ Install the Align Jig and fasten the screw after attaching it to the cabinet. (Fig.3-2)
  • Page 39 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation ④ Install the first stage based on the cabinet installed according to the Align jig. (Fig.4) ⑤ When installing the second stage, fasten the screw after attaching it to the Align jig in the same way as the first stage installation method.
  • Page 40 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation 1. When installing the second cabinet after the first, in order not to collide between modules - Push the ① and ② modules to the side. - Attach the edge protection jig V to the corner. (Fig.1) - Push the module ③...
  • Page 41 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation 2. When installing the second stage cabinet after installing the first stage, in order not to collide with the modules - Push the ① and ② modules to the side.
  • Page 42 5. Cabinet + Frame Installation Samsung Electronics ◇ Half-cabinet Z-step adjustment - Each Half-Cabinate has eight height controls. (4 corners / 4 sides) - Two Half-Cabinet Z-Step adjustments are as follows ① Check the corner of the Half-Cabette to check if there is a difference.
  • Page 43 5. Cabinet + Frame Installation Samsung Electronics • Adjust Z-leveling between modules. 1. Attach Suction-Pad 2. Move Module 2.0mm 3. Insert Gap-Tool Turn Gap-Tool 90degree 2.0mm Un-Lock Lock ~2mm 90° 5. Hold Module by Hand Turn Gap-Tool 90degree, Remove Gap-Tool 4.
  • Page 44 5. Cabinet + Frame Installation Samsung Electronics - Assemble the cover PCB at the bottom of the cabinet after the first row cabinet installation. - After assembling the Cover PCB, tighten the braid bolts to align the module pixels. * After installing each unit, make sure that the switch on the back of the cabinet is in the “ STB ” mode Cover PCB Fig.1 Fastening screw from Cover PCB to adjust pixel alignment...
  • Page 45 5. Cabinet + Frame Installation Samsung Electronics ◇ Align modules in X,Y direction - Install the cover PCB on each border to align the module. ※ The module alignment must be performed after the step operation is completed. ① Assemble the Cover PCB in the upper left and right corners of the screen. M4L5 tanning bolts are assembled only 1 ~ 2mm and later.
  • Page 46 5. Cabinet + Frame Installation Samsung Electronics ◇ Align modules in X,Y direction - After installing the cover PCB on each border, install the Holder PCB. ※ Holder PCB is a device to prevent the gap between modules. ① Complete all alignment work using Cover PCB and install it.

  • Page 47: Disassembly & Front Service

    6. Disassembly & Front Service Samsung Electronics ◇ Remove bezel and remove Cover / Holder PCB Remove bezel GAP SHEET Cover-PCB Vertical center line Remove bezel and Cover / Holder PCB Horizontal center line M3L6 M4L6 Holder-PCB M4L6...
  • Page 48 6. Disassembly & Front Service Samsung Electronics Absorber Lock Un-Lock ※ Absorber : Handle type tool that fixed on cabinet front side(LED side) to prevent damage to LED Modules while assembly/disassembly, moving half- cabinets. ※ Handle should be locked in vertical.
  • Page 49 6. Disassembly & Front Service Samsung Electronics ★Caution★ Cannot use Magnet JIG of other LED display model. (weak magnetic force) - Magnet Jig Use proper Magnet JIG matching with specification. 1. Access carefully on 45° not to damage modules. (Do not contact Jig to module, 1cm apart) ※...
  • Page 50 6. Disassembly & Front Service Samsung Electronics Half-Cabinet disassembly • ① Based on the Half-Cabinets to be replaced, the Half-cabinets on the left/right and top should be pushed outward. (Edge Protection is needed. Refer to the Next) ※ UHD Screen (16Cabinet / 32 half-cabinet) Repairing Half- Cabinet ②...
  • Page 51 6. Disassembly & Front Service Samsung Electronics • Edge Protection Push cabinets toward outside to get 2mm gap that located on same vertical line with repairing Half-cabinet ※ Cover PCB should be removed. ※ pushing order is important. Follow the numbers ※...
  • Page 52 6. Disassembly & Front Service Samsung Electronics Edge Protection • ★Caution★ Be careful not to damage module ③ Insert GAP Tool at middle of Top/Bottom edge of half- cabinet to fix gap. A/S-ASSY GAP TOOL ※ Insert horizontally, turn vertically and fix.
  • Page 53 6. Disassembly & Front Service Samsung Electronics Removing cable and disassemble Half-Cabinet • ⑤ Identify location of cables need to be removed. ※ Refer to the TCON board picture. (top : Master / bottom : Slave) ※ Remove the cables close to each other.
  • Page 54 6. Disassembly & Front Service Samsung Electronics Removing cable and disassemble Half-Cabinet – Using PLIER JIG • ■ Using PLIER JIG, remove 26P Power Cable(SMPS, Redundancy) ※ There is a groove that takes locking on the top head. ※ Locking can slip if it does not get to the groove correctly A/S-ASSY PLIER JIG ※...
  • Page 55 6. Disassembly & Front Service Samsung Electronics Changing to new Half-Cabinet • ※ New cabinet must be changed after conduct Dehumidifying mode Aging. (Refer to page 100) ⑦ Remove Cover corner from Buffer Cabinet laid on the floor and lift up half-cabinet with absorber attached.
  • Page 56 6 Disassembly & Front Service Samsung Electronics Remove Cable and screw • ① Remove Cover Terminal. Cover terminal Screw point Remove Cover Terminal first since this screw Point is concealed. ※ Note that Master Cover terminal has switch on it.
  • Page 57 6. Disassembly & Front Service Samsung Electronics Remove Cable and screw • ② Remove cable and screw of TCON Board. ※ FFC Cable ※ rear side of half-cabinet Lift up lock and pull out to remove cable. ※ Power Cable...
  • Page 58 6. Disassembly & Front Service Samsung Electronics • Remove and Change TCON Board ③ Remove TCON Board and replace it. ④ Assembly is reverse order of disassembly. ※ The Gap pad is attached to the TCON or Bracket-PCB, so don’t skip when replacing new board.
  • Page 59 6. Disassembly & Front Service Samsung Electronics • Module (Half-cabinet Module) Store & Packaging ① Repairing Half-cabinet should be stored with buffer cabinet. ※ Repairing Half-Cabinet Dissemble Half-Cabinet from existing Buffer Cabinet Change it with Repairing Half-cabinet ※ Repairing Half-Cabinet ※...
  • Page 60 6. Disassembly & Front Service Samsung Electronics • Module (Half-cabinet Module) Store & Packaging ※ Module (Half-Cabinet module) (front/rear) ③ ※ Remove repairing half-cabinet from stored buffer cabinet. ※ Remove repairing half-cabinet from buffer cabinet ④ Package Half-cabinet in The Wall LED Module BOX.
  • Page 61 6. Disassembly & Front Service Samsung Electronics Caution ◆ : SMPS Discharge Grab point : - Before you touch or remove the SMPS, touch the two Touchable Area without additional discharging process) discharge points using a discharge Jig to verify the SMPS is full discharged.
  • Page 62 6. Disassembly & Front Service Samsung Electronics SMPS disassembly • ① Remove screws over the insulator on SMPS. (6EA) ② Remove AC INLET Cable connected to SMPS. (Do not remove 26pin Power Cable yet) ★ Caution ★ Do not touch except marked spot.
  • Page 63 6. Disassembly & Front Service Samsung Electronics SMPS disassembly • ③ Hold 26pin Power Cable and bottom of SMPS. ④ Lift up the bottom part and pull down to separate. Be careful of protruding part at top of SMPS shield.

  • Page 64: Cable Connection

    CONNECT the devices less than the recommended maximum number of devices. ※ Samsung Electronics is not responsible for AC power connecting exceed recommended maximum number of devices. • The label info which is attached behind product shows rated power of cabinet and rated current of outlet.
  • Page 65 7. Cable Connection Samsung Electronics 7-2. The caution for Cabinet installation and Cable connection(Full Front) 1) The installation order proceeds from the left or right end to the other end. → Cabinet installation order and cable connection order may be different.
  • Page 66 7. Cable Connection Samsung Electronics 7-3 The direction for Cabinet installation 1) Installation of First row cabinet starts at the bottom of Left-end. 2) After installing cabinets one line is complete, make sure the connection is OK by connecting OCM/Power cable. Then, Install next line.
  • Page 67 7. Cable Connection Samsung Electronics Cable Connection : Data flow standard [FHD] ◎ IW008J : Connect OCM cable Forward direction Case 1: Reverse internal Link internal Link ID:2 internal Link internal Link Forward...
  • Page 68 7. Cable Connection Samsung Electronics Cable Connection : Data flow standard [FHD] ◎ IW008J : Connect OCM cable Forward direction Case 2: internal Link internal Link Reverse internal Link internal Link Forward ID:2...
  • Page 69 7. Cable 연결 Samsung Electronics Cable Connection : Data flow standard [FHD] ◎ IW012J : Connect OCM cable Forward direction Case 1: Reverse internal Link internal Link internal Link ID-19 ID-18 ID-13 ID-12 ID-11 ID-10 internal Link internal Link internal Link...
  • Page 70 7. Cable 연결 Samsung Electronics Cable Connection : Data flow standard [FHD] ◎ IW012J : Connect OCM cable Forward direction Case 2: Reverse internal Link internal Link internal Link ID-11 ID-10 ID-13 ID-12 ID-19 ID-18 internal Link internal Link internal Link...
  • Page 71 7. Cable 연결 Samsung Electronics Cable Connection : Data flow standard [FHD] ◎ IW016J : Connect OCM cable Forward direction Case 1: ID-29 ID-28 ID-27 ID-26 ID-17 ID-16 ID-15 ID-14 internal Link internal Link internal Link internal Link ID-31 ID-30...
  • Page 72 7. Cable 연결 Samsung Electronics Cable Connection : Data flow standard [FHD] ◎ IW016J : Connect OCM cable Forward direction Case 2: ID-15 ID-14 ID-17 ID-16 ID-27 ID-26 ID-29 ID-28 internal Link internal Link internal Link internal Link ID-13 ID-12...
  • Page 73 7. Cable Connection Samsung Electronics 7-5 Cable Connection : OCM cable installation standard ◎ Cable connection required after cabinet installation - 2x2 Connection (FHD IW008J) DATA OUT DATA OUT DATA IN DATA IN DATA OUT DATA IN DATA OUT DATA IN...
  • Page 74 7. Cable 연결 Samsung Electronics 7-5 Cable Connection : OCM cable installation standard ◎ Cable connection required after cabinet installation - 3x3 Connection (FHD IW012J) DATA OUT DATA IN DATA OUT DATA IN DATA OUT DATA IN DATA OUT DATA OUT...
  • Page 75 7. Cable 연결 Samsung Electronics 7-5 Cable Connection : OCM cable installation standard ◎ Cable connection required after cabinet installation - 4x4 Connection (FHD IW016J) DATA OUT DATA IN DATA OUT DATA IN DATA OUT DATA IN DATA OUT DATA IN...
  • Page 76 7. Cable Connection Samsung Electronics ◎ Apply COVER CAP to POWER IN CABLE of the top cabinets. COVER-CAP POWER-IN CABLE COVER-CAP 4*4 (Example)

  • Page 77: S-Box Installation And Connection

    8. S-BOX Installation and Connection Samsung Electronics • S-BOX Installation Precautions ① Product recommend installing this product in a standard 19-inch server rack. ※ When connecting two or more times for the purpose of using multi-link HDR, install it on the ground shielded rack and use it.
  • Page 78 8. S-BOX Installation and Connection Samsung Electronics • S-BOX Connection ① Input the video signal to the S-BOX. (Input terminal : HDMI, DP) ② Check the signal input from SOURCE STATUS.(RED : HDMI1 , GREEN : HDMI2, Blue : DISPLAY PORT) ③...
  • Page 79 8. S-BOX Installation and Connection Samsung Electronics ⑧ Instruction for handling HDBase-T cable ★ Orderly Rolled (Recommend) Random Rolled ★ (Not Recommend)  Do not use “comb” or “pinstripe” cable  Use HDBase-T cables with 15 meter long at minimum and 100 meter long at maximum.
  • Page 80 8. S-BOX Installation and Connection Samsung Electronics ⑧ Instruction for handling HDBase-T cable  EMI sources: Keep the cable away from electromagnetic interference environments such as high-voltage electrical cables, electric motors (such as elevators or refrigerators), fluorescent, light-fixtures and so on ...
  • Page 81 8. S-BOX Installation and Connection Samsung Electronics ⑨ Instruction for trimming HDBase-T cable on site.  STP RJ45 shielded Plug. RJ45 Connector should be CAT6 or CAT7 shielded RJ45 and load bar. Load bar  Insert conductors into the plastic loader : Using the standard wiring scheme shown here (T-568B), insert the conductors into the plastic loader piece of the R-J45 connector.
  • Page 82 8. S-BOX Installation and Connection Samsung Electronics ⑩ Instruction for trimming HDBase-T cable on site.  Slide the plastic loader down the cable : Slide the plastic loader down the cable as close to the base as possible.  Cut all conductors Using the wire cutters, cut all conductors leaving approximately 0.5” remaining.
  • Page 83 8. S-BOX Installation and Connection Samsung Electronics ⑩ Instruction for trimming HDBase-T cable on site.  Flip the drain wire up onto the RJ-45 connector Flip the drain wire up onto the RJ-45 connector. Clamp the strain relief down on the purple jacket of the BC-HDKat6a cable using the pair of pliers.
  • Page 84 8. S-BOX Installation and Connection Samsung Electronics • S-BOX Connection (Redundancy) ① If Redundant Spec should be used, Connect from DATA IN port of Interface Gender to DATA OUT port of the last cabinet by using OCM Cable. SNOW-1801U • For HDBT signal stability, use the cable above CAT6 *STP, *FTP level.
  • Page 85 8. S-BOX Installation and Connection Samsung Electronics • S-BOX Connection (External IR Receiver) ※ One IR receiver is provided per set. - IR receiver can be connected to S-Box or I / G Card (Interface Card). ※ If you want to connect to the I / G card, you must set Network Standby – “On” in the setting and then connect.
  • Page 86 • S-BOX Connection (Panel Configuration) ① S-Box Picture Setting according to model • The default picture configurations are optimized for LH015IFH in Samsung factory. • The picture configurations will be configured automatically when you finish the installation. • For the best picture quality, Please connect S-Box and LED displays via LSM software properly.
  • Page 87 8. S-BOX Installation and Connection Samsung Electronics • S-BOX Connection (Grouping) ① Enable S-Box Grouping Home → Video Wall : OFF → On  [Cautions!!] Before executing S-Box Grouping in LED Signage Manager (LSM), make sure to set the resolution of the input source equipment to S-Box Grouping supported resolution..
  • Page 88 8. S-BOX Installation and Connection Samsung Electronics ③ Setup the resolution of input PC  PC: Click the right button of mouse → Click Screen resolution → Click Advanced settings  Click “Monitor” tap → Monitor Settings → Setup “Screen refresh rate” to 60Hz...
  • Page 89 8. S-BOX Installation and Connection Samsung Electronics ④ Supported resolution for S-box grouping (1/2)
  • Page 90 8. S-BOX Installation and Connection Samsung Electronics ④ Supported resolution for S-box grouping (2/2)
  • Page 91 8. S-BOX Installation and Connection Samsung Electronics ⑤ Picture menu setting  When using S-Box grouping, you must set Picture mode to Calibration. Calibration mode deactivates Dynamic Contrast, Black Tone, Auto Motion plus function so that there is no screen difference between S- Box.
  • Page 92 8. S-BOX Installation and Connection Samsung Electronics • S-BOX Connection (Service port) ① The service port is dedicated port for monitoring to check the usage of OSD and the source being played at the initial installation of the S-BOX ②...
  • Page 93 8. S-BOX Installation and Connection Samsung Electronics • Simple wall mode operation  If the user does not use the product and does not want the black screen output, it simply allows the wallpaper to be displayed and used.  If Screen resolution is below S-Box output resolution, you can turn on Simple wall mode in Factory menu ①...
  • Page 94 • - Samsung Display Solutions (https://displaysolutions.samsung.com) # authority requirement # Samsung Display Solutions > SOLUTIONS > SOFTWARE SOLUTIONS > LED Signage Solution > LED Signage Manager - SLM (https://www.secslm.com) # authority requirement # SLM > Help > Download Center > "LED Signage Manager" or "LSM"...
  • Page 95 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs Network IP Setting Tool Execute : [Start] – Program – Samsung – LED Signage Manager – Network Configuration Connect PC and Sbox with RS232C Cable, select connected SerialPort(COM*). And click “open” button.
  • Page 96 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Software that adjusts the LED Cabinet Layout in Remote • S-box Ethernet PC and S-box should be connected through Ethernet connection. HDBT Control PC...
  • Page 97 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Start– Login Page • If the LSM gets operated for the first time, the page to set the password will appear. To set the password, users have to input the same password two times and then click the “Start”...
  • Page 98 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) New Connection • To add connection information, you can either use Search function or input the IP address by yourself. If you click on the Search button, the IP addresses available on S-BOX in the same network will appear.
  • Page 99 9. Settings and How to Use Samsung Electronics [★ Cautions!] Recommend to use static IP address for the LED devices. If DHCP is used, IP address is changed automatically and LSM can be 9-1 Control Program for PCs disconnected. The 192.168.10.x band is used for internal communication of the LED Cabinet.
  • Page 100 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs [★ Cautions!] LSM(LED Signage Manager) The network port 1515 and 48485 are used for internal communication between S-BOX and LED Cabinet. It should be include the firewall or network exception if customer used secured network.
  • Page 101 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Main Window-Home Window • Input source: Input source, resolution, connection time of S-BOX are shown. Cabinet Layout : Layout, number of units, number of connections and number of disconnections in all LED cabinets are shown.
  • Page 102 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Main Window-Edit Connection Layout Window • Connection layout: The location and the layout of each LED cabinet are adjusted in the output source area of the S-BOX.
  • Page 103 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Main Window-Connection Window • Device connection list view: Check S-BOX composition, modify and delete S-BOX connection, show by each LED Cabinet Group Connection layout (View Port):...
  • Page 104 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Main Window-Connection Window - Device Information/Setting View • 1. Basic : . SBOX power on / off, input source switch, screen mute / stop screen 2.
  • Page 105 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Main Window – Connections Window – Device Information / Settings View • 6. LED Cabinet Calibration . Cabinet Calibration └ Cabinet RGB CC : Correct the RGB CC Matrix in cabinet units.
  • Page 106 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Main Window-Connection Window - Sub Information View • Monitor Window: Checking MDC communication log and connected device information available, able to be extracted via file...
  • Page 107 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Main Window-Preference • Options number of times the command retried interval of checking error status alarm temperature warnings Support program language Log data management...
  • Page 108 9. Settings and How to Use Samsung Electronics 9-1 Control Program for PCs LSM(LED Signage Manager) Dehumidification using LSM • Dehumidification button is located in S-Box menu When you click the button, dehumidification starts You can see how long it takes...

  • Page 109: Issue And Solution

    10. Issue and Solution Samsung Electronics  S-Box Network Connection Issue with LSM ① The LSM cannot find the S-Box or the Disconnected message is displayed. -. Check the Ethernet cable connection. -. Check the IP settings of S-Box. -. Check if the target IP is the IP of the S-Box in the LSM.

  • Page 110: Color Calibration

    11. Color Calibration Samsung Electronics ■ On-Site Calibration - Provides calibration function using measurement equipment (Colorimeter) / mobile - Automate module unit adjustment that was adjusted with the existing naked eye by S / W - Module / Half Cabinet / Cabinet / Screen Calibration - Available for Install / Maintenance : The replacement module can be adjusted when replacing the Spare / Service Module.
  • Page 111 Samsung Display Solution (displaysolutions.samsung.com) # download permission required # Samsung Display Solutions > SOLUTIONS > SOFTWARE SOLUTIONS > LED Signage Solution > Color Expert LED - Reference values can be measured and input directly by the user - PC Colorimeter Calibration Manual...
  • Page 112 Samsung Display Solution (displaysolutions.samsung.com) # download permission required # Samsung Display Solutions > SOLUTIONS > SOFTWARE SOLUTIONS > LED Signage Solution > Color Expert LED - Calibration unit is selected from module or cabinet unit - Specify Reference and Target...

  • Page 113: Bezel Installation

    12. Bezel Installation Samsung Electronics • Installing Frame Bezel 1. Attach ASSY FRAME-BEZEL SIDE to the cabinet. • Check for allowable gaps for the each FRAME-BEZEL SIDE. • If it needs to adjust gaps, it can be adjusted by attaching or detaching GAP SHEET on the magnets.
  • Page 114 12. Bezel Installation Samsung Electronics 2. Use SCREW(M3,L5) to fasten the BRACKET LINK to the right side of the FRAME-BEZEL TOP BOTTOM. M3,L5 BRACKET CENTER...
  • Page 115 12. Bezel Installation Samsung Electronics 3. Place the ASSY FRAME-BEZEL TOP BOTTOM to the top left of the cabinet. • Align the FRAME-BEZEL SIDE and FRAME BEZEL TOP BOTTOM to ensure there is no gap between them. • Use 2 SCREW (M3, L5) to fasten the left side of the FRAME BEZEL TOP BOTTOM to the FRAME BEZEL SIDE.
  • Page 116 12. Bezel Installation Samsung Electronics 4. Place the FRAME-BEZEL TOP BOTTOM to the top right of the cabinet. • Align the FRAME BEZEL SIDE and FRAME-BEZEL TOP BOTTOM to ensure there is no gap between them. • Use 2 SCREW (M3, L5) to fasten the right side of the FRAME-BEZEL TOP BOTTOM to the FRAME BEZEL SIDE.
  • Page 117 12. Bezel Installation Samsung Electronics 5. Use 2 SCREW (M3, L5) to fasten the left side of the FRAME-BEZEL TOP BOTTOM. [Fig.1] 6. Use 6 SCREW (M4, L8) to fasten the FRAME BEZEL TOP BOTTOM to the screw holes on the cabinet. [Fig.2]...
  • Page 118 12. Bezel Installation Samsung Electronics 7. Repeat steps 2-6 to install the cabinet bottom. * Make sure that there is no gap between the FRAME BEZEL SIDE and FRAME BEZEL TOP BOTTOM units on both ends. M3,L5 M3,L3 M4,L8 M4,L8...
  • Page 119 12. Bezel Installation Samsung Electronics • Extending the FRAME BEZEL Extending vertically • Connect FRAME-BEZEL LEFT & RIGHT for over 5~8 cabinets high M3,L3...
  • Page 120 12. Bezel Installation Samsung Electronics • Extending the FRAME BEZEL Extending side by side * Follow the basic installation steps and the below guidelines. • Extending 6 cabinets side by side Connect 3 FRAME BEZEL TOP BOTTOM units. Fastening with...
  • Page 121 13. Appendix – Module Attachment Principle Samsung Electronics Section view HOLDER-MAGNET It is possible to adjust height by using driver. (4points / module) => Return in a LED MODULE counterclockwise direction. (1mm/1rotation) BRACKET-SUB BRACKET MAGNET LED MODULE MAGNET BRACKET SUB...
  • Page 122 13. Appendix – How to separate Module Samsung Electronics < Edge protection > Disassemble Cover-PCB Attach Protection Make gap (move module 2mm ) Separate Module with Magnet jig Full Protection Module for change Magnet Magnet in protection Stud in module section 0.5mm gap...
  • Page 123 13. Appendix ※ Certified Cable by HDbaseT Samsung Electronics ★ For HDBT signal stability, do not use CAT5E cables even though the cables are included in the following list Vendor Model Name Vendor Model Name Kramer Electronics BC-HDKat6a Snap AV...
  • Page 124 13. Appendix ※ Certified Cable by HDbaseT Samsung Electronics ★ For HDBT signal stability, do not use CAT5E cables even though the cables are included in the following list Vendor Model Name Vendor Model Name HNCPRO(TM) HOME NETWORK CABLE Trends Electronics...

This manual is also suitable for:

Lh012iwj seriesLh016iwj seriesSnow-1810u

Table of Contents