Page 1 Samsung Electronics LED Display Installation Manual Cabinet : LH008IWR (P0.84) Media Box : SBB-MBOXR48 Ver. 2.0...
Page 2 Revision History Samsung Electronics Version Date (Y/M/D) Description 2020/03/20 New Release...
Page 3 ∙ Case when period between unpacking and turning on the power of products is spent more than 7days, even though it is under Samsung recommended storage condition. ∙ Case when production date on the label is exceed more than 6 months, even though vacuum packaging is no problem.
Page 4 Dehumidification guidance – during operation Samsung Electronics  Electrical short in package is possible to happen during products are working.  For keeping quality of products during installation, please refer below cautions. - If one of below case meet during operation, MUST do dehumidification process.
Page 5 Dew condensation due to overcooling Samsung Electronics  Even though meet with Samsung recommended operation condition, dew condensation is possible to happen when surface of products is colder than environment temperature or hot & humid air blow to cooled surface of products.
Page 6 Guidance of latest firmware Samsung Electronics  When install products, please update latest firmware on online - You can download latest firmware from SLM site. ∙ URL of SLM Page : https://www.secslm.com ∙ After login  Help  Download Center에서 Download ∙...
Page 7: Table Of Contents
Table of Contents Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 8 Product installation flow Samsung Electronics Check product installation precautions (4~11page) Check heat dissipation inspection (12~20page) Installation frame (21~37page) Check cabinet operation (45~47page) Installation cabinets and cables (48~83page) Installation bezel and sensors (84~102page) Installation Media Box and LSM (125~166page) Calibration cabinets (167~169page)
Page 9: Product Information And Precautions For Installation
Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 10 1. Product Information and Precautions for Installation Samsung Electronics ◇ Cabinet Installation Components Picture Description Picture Description Cabinet Product Certification LH008IWR AC Extension Power Standard guide Cable (to Cabinet) AC Power Cord Cover-PCB x1ea (to Wall Outlet) ※ Not included on LH008IWR**/XU model.
Page 11 1. Product Information and Precautions for Installation Samsung Electronics • Media Box Installation Components Picture Description Picture Description Bridge Box Media Box SBB-MBOXR48 24pin system cable x 5 Remote control AC/DC Adaptor, Power Bluetooth/Wi-Fi module cable cable Module Rx x 8...
Page 12 1. Product Information and Precautions for Installation Samsung Electronics ◇ Frame Kit (refer to page 22,23) Installation Frame Kit Note configuration VG-LFR08SWW (1 Set) VG-LFR08FWW (4 Set) 2K (FHD) VG-LFR08TWW (9 Set) VG-LFR08UWW 4K (UHD) (16 Set) VG-LFR08FWW x2 (25 Set)
Page 13 1. Product Information and Precautions for Installation Samsung Electronics ◇ Storage Condition Condition Value Recommend Temperature -20℃ ~ +45℃ -20℃ ~ +45℃ Humidity 5~95% 5~65% Hight 3000m 3000m ◇ Pre-heating Process If you do not operate for more than 30 days, you need to dehumidify it before operation. (refer to page 46)
Page 14 1. Product Information and Precautions for Installation Samsung Electronics • Precautions for Installation (LED damage) Caution Image [ Beware of Outside Impact, Fall] ① Beware not to cause any impact on the LED screen or drop the product on the floor MODULE after the protection gets taken off for installation.
Page 15 1. Product Information and Precautions for Installation Samsung Electronics ◇ Caution for cleaning screen ★Caution★ - Watch out for damage when cleaning gap between Half- Cabinets - Watch out for damage when cleaning gap between Modules - Do not insert any cleaning tool or spay cleaner directly into...
Page 16 1. Product Information and Precautions for Installation Samsung Electronics • The power cable must have a click sound, and the WDM module must be pushed into the rear fixing holder. The OCM cable and the USB-C cable should be inserted into the fixing holder.
Page 17 1. Product Information and Precautions for Installation Samsung Electronics ◇ Installation preparation • It is on the Prepare Frame kit installation page(p.22) included in Frame Kit (IWJPA-WL008F). ※ Recommended standard • Provided in accessory kit. (CY-WJJPWP). ※ It should be purchased together when purchasing the product separately.
Page 18: Check Point About The Radiant Heat
Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 19 2. Check Point about the Radiant Heat Samsung Electronics  Installation condition - SAMSUNG FRAME usage condition - The installation of direct solar window conditions is avoided. (If it is inevitable to install directly, make sure to contact our technical team) .
Page 20 2. Check Point about the Radiant Heat Samsung Electronics  Heat generation during screen installation (Additional air conditioning) - Heat generation value is according to the screen size and should be added to the existing air conditioning amount. Additional air conditioning load Screen size Watt∙h...
Page 21 2. Check Point about the Radiant Heat Samsung Electronics  Buried installation condition (Recommended using SAMSUNG FRAME, FAN ARRAY kit) Recommended conditions : At least 500mm must be secured (set ~ ceiling) Min 30mm If the indoor temperature is less than 25degrees due to the air conditioner operation,...
Page 22 2. Check Point about the Radiant Heat Samsung Electronics  Wall installation conditions (Recommended using SAMSUNG FRAME, FAN ARRAY kit) Recommended conditions : At least 500mm must be secured (set ~ ceiling) If the indoor temperature is less than 25degrees due to the air conditioner operation, 100mm is possible.
Page 23 2. Check Point about the Radiant Heat – Fan Samsung Electronics  Components required quantity when applying the 4K, 6K, 8K Screen Components Figuration FAN Array Power Adaptor (DC14V) DC Daisy chain Cable FAN Control Cable...
Page 24 2. Check Point about the Radiant Heat – Fan Samsung Electronics  4K, FAN Installation sequence ① Install the Fan array in the frame as shown below. ② Connect the DC daisy chain cable to the Fan array “Link Cable IN” and “Link Cable OUT”.
Page 25 2. Check Point about the Radiant Heat – Fan Samsung Electronics  4K, FAN Installation sequence ③ Connect the fan control signal cable to the 2 cabinet “Data Out” and the fan array “Signal Connector” ④ Put the DC Power Adaptor in to the rear holder of the 2 cabinet and connect it to the fan array “DC power”...
Page 26 2. Check Point about the Radiant Heat – Fan Samsung Electronics  When using SAMSUNG FRAME and FAN ARRAY kit - Installed all except at the bottom. 4K, FAN Installation and Cable Connection (Rear view)
Page 27 Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 28 3. Frame Installation Samsung Electronics ◇ Frame Kit Composition (1/2) ⓑ (Units) ⓑ ⓒ ⓐ VG-LFR08SWW VG-LFR08FWW VG-LFR08TWW VG-LFR08UWW Item ( 1 X 1 ) ( 2X 2 ) ( 3 X 3 ) ( 4 X 4 ) ⓐ...
Page 29 3. Frame Installation Samsung Electronics ◇ Frame Kit Composition (2/2) 5X5 : 2 of 2X2 & 2 of 3X3 6X6 : 4 of 3X3 ● ● 7X7 : 2 of 3X3 & 2 of 4X4 8X8 : 4 of 4X4 ●...
Page 30 3. Frame Installation Samsung Electronics ① Assemble the Bracket Side / Middle and Bracket H. - Place the bracket side / Middle on the floor and assemble it by inserting the Stud-Pem of the bracket H. (Fig.1) . Bracket Side: Both Side Frames, Bracket Middle : Middle Frame - Assemble using M6 Screw.
Page 31 3. Frame Installation Samsung Electronics ② Assemble the level on the bracket side according to the required height position. - Move the level up and down to fasten the screw (M4) at the desired location. (Fig.3) Fig.3 Leveler Assembly...
Page 32 3. Frame Installation Samsung Electronics ③ Firstly fasten the assembled frame to the wall. - Attach the assembled frame to the wall and adjust the desired height and level (p.28,29 reference) and fasten one place in the upper center. (Fig.4) - When the frame is attached to the wall, the part where the bracket H and space are created use a 6mm hexagonal wrench to rotate the Leveling bolt to correct the gap.
Page 33 3. Frame Installation Samsung Electronics - While working, use the remaining Bracket Middle to adjust the Z axis shortening in each middle.(Fig.7) * Sometimes, if the frames and walls are not parallel, Fasten the M6 screw to the hole on the left and right of Leveling Bolt to adjust the frame and the wall to be parallel.
Page 34 3. Frame Installation Samsung Electronics - In order to complete the wall work, it must be finally vertically and horizontally adjusted.. - There is method of using a leveler included in an existing FRAME KIT, or using a laser leveler.
Page 35 3. Frame Installation Samsung Electronics * How to Use an Laser Leveler * - Align the laser horizontally and vertically to the Bracket H, Bracket Side / Middle position. - For accurate criteria, product use with precision of ± 1mm / 10m is recommended.
Page 36 3. Frame Installation Samsung Electronics - When all wall work is completed, screw the remaining 24 places (the number of bolt recommended fasteners: total 25 places). (Fig.7) - After finishing the leveling work, unscrew the screw that assembled the Bracket Side / Middle and Bracket H and remove the Bracket H.(Fig.8)
Page 37 3. Frame Installation Samsung Electronics ※ Additional adjustment of GAP between frame and wall (Reference) - After fastening the frame with screws on the wall, Use the Spacer-ETC if additional adjustment of GAP is required. - Unfasten the screws in the area requiring adjustment. (Fig.1) - One hand takes the frame and makes space, and the other hand inserts Spacer-ETC into the empty space.
Page 38 3. Frame Installation Samsung Electronics ※ Precautions for Screw Fixing Concrete or interior walls with sufficient thickness Standard conditions for installation according to the type of wall Check the type of wall and install it. First, check the status of the It can be installed on a thick concrete or interior wall.
Page 39 3. Frame Installation Samsung Electronics ※ Extension of frame in vertical direction - If 4x4 or more frames are installed (5x5 to 8x8), extend the operation using Joint C and Bracket H. - General frame installation is performed. (See Bracket Side / Middle and Bracket H assembly, p.24 reference)
Page 40 3. Frame Installation Samsung Electronics ※ Extension of frame in vertical direction - Connect and assemble Joint C between extended frames. (Use the M6 screw the same as the bracket H) * The frame to be extended is also proceeded with horizontal and vertical alignment. (p.28,29 reference)
Page 41 3. Frame Installation Samsung Electronics ※ Extension of frame in horizontal direction - After installation, attach it to the wall and use a laser and jig to pinpoint the exact location. (p.28,29 reference) * Check the z-axis shortening with Bracket Middle while holding the hand.(p.27 reference)
Page 42 3. Frame Installation Samsung Electronics ※ Extension of frame in horizontal direction - The horizontal direction extension is extended using Bracket H by adding MIDDLE FRAME. - Add MIDDLE FRAME according to the desired size (5X5 ~ 8X8) and close with SIDE FRAME.
Page 43 3. Frame Installation Samsung Electronics ※ Extension of frame in horizontal direction - After the extension work is completed by connecting the bracket H, check the vertical and horizontal using the laser and jig.
Page 44 3. Frame Installation Samsung Electronics - When all extension tasks are completed, remove Joint C and Bracket H and check the vertical and horizontal using Jig.
Page 45: Preparation For Cabinet Installation
Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 46 4. Preparation for Cabinet Installation Samsung Electronics ◇ Preparations Before Installation ① Remove the Box tape at the upper area and then open up the box. (Fig.1) ② Remove the Top–Cushion and pull-out the set that packed with Bag-Shielding. (Fig.2) ③...
Page 47 4. Preparation for Cabinet Installation Samsung Electronics ⑤ Attach the holder stand to the bottom of the SET and connect the power supply to check for screen abnormalities. (Fig.4) ※ How to check for screen abnormalities(refer to P.46) ⑥ Release the cover corner section four screws.
Page 48 4. Preparation for Cabinet Installation Samsung Electronics ⑦ Unfasten the 14 screws on the Holder-PCB and the 2screws on the Cover-PCB to separate those screws and ⑧ Remove the protective sheet attached to the four sides (Top/Bottom/Left/Right). (Fig.4) ※ If the Cover-Corner is assembled and laid down for a long time, the Bracket-Frame is dropped down.
Page 49 4. Preparation for Cabinet Installation Samsung Electronics ⑨ For the 15 countries integrated model, prepare CABLE for the region. ※ In 15 countries (EU, Russia, Iran, Korea, Indonesia, Australia, UK, Nigeria, Hong Kong, Singapore, Malaysia, Taiwan, USA, Argentina, Japan) Cables are provided separately as (LH008IWR**/XU).
Page 50 4. Preparation for Cabinet Installation Samsung Electronics ◈ Reference : Process of Dehumidification ※ If you do not operate for more than 30 days, you need to dehumidify it before operation. SWITCH POWER OUTLET POWER INLET ※ Caution : 1. IWR (LH008IWR) Doesn’t power on in STB mode(switch).
Page 51 4. Preparation for Cabinet Installation Samsung Electronics ◈ Reference : Process of Dehumidification ※ If you do not operate for more than 30 days, you need to dehumidify it before operation. The Dehumidification process progresses automatically for 24 hours as the brightness increases gradually...
Page 52 4. Preparation for Cabinet Installation Samsung Electronics ◈ Reference : Process of screen check Toggle SWITCH 화면 검사 사진 확인 POWER INLET Check the picture of the screen ◈ Internal white pattern 1. After turn on power, press the toggle switch button for three seconds 2.
Page 53: Cabinet + Frame Installation
Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 54 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET [ UHD Screen (16Cabinet / 32 half-cabinet) ] ※ When installing Cabinet to the FRAME KIT, CABLE must be connected immediately. ※ The No. 1 CABINET starts at the bottom right and becomes the standard for cabling.
Page 55 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 1. 1st CABINET CABLE connection - Connect 7 cables. (Fig.1) * Refer to the following page(p.51~56) for detailed CABLE installation. ① ② AC POWER DATA ③ ④...
Page 56 5. Cabinet + Frame Installation Samsung Electronics ※ CABLE Installation/Caution ① (It is the standard to connect cable to SET before installation in FRAME) ① DATA OUT CABLE Connection ※ Connect to all cabinets except the top. ※ Both CABLE HEAD shapes are different.
Page 57 5. Cabinet + Frame Installation Samsung Electronics ※ CABLE Installation/Caution ② (It is the standard to connect cable to SET before installation in FRAME) ② POWER OUT CABLE Connection ※ Connect to all cabinets except the top. (It is connected up to 4 stages, and more than 5 stages are excluded from 4 stages and the top.) ※...
Page 58 5. Cabinet + Frame Installation Samsung Electronics ※ CABLE Installation/Caution (It is the standard to connect cable to SET before installation in FRAME) ③ SENSOR CABLE & ⑥ Bluetooth/Wi-Fi CABLE Connection ※ The SENSOR cable is applied only four cabinets.
Page 59 5. Cabinet + Frame Installation Samsung Electronics ※ CABLE Installation/Caution (It is the standard to connect cable to SET before installation in FRAME) ④ DATA IN CABLE (WDM Rx Module) Connection ※ Connect one by 4 stages vertically / 2 cabinets horizontally.
Page 60 5. Cabinet + Frame Installation Samsung Electronics ※ CABLE Installation/Caution (It is the standard to connect cable to SET before installation in FRAME) ⑤ DATA OUT CABLE Connection ※ Connect to the cable connected to the ④ CABLE. stopper ※ Do not cable does not pass over the BOLT ⑤...
Page 61 5. Cabinet + Frame Installation Samsung Electronics ※ CABLE Installation/Caution (It is the standard to connect cable to SET before installation in FRAME) ⑦ AC POWER IN CABLE Connection ※ Apply only to the bottom cabinet. (If it is more than 5 stages, it is applied only to 1,5 stages) ⑦...
Page 62 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 1. 1st CABINET CABLE connection - Install Bridge Box. (Refer to p.58) - Install to Frame kit. (Refer to p.59~60 ) ※ Always work with two people.
Page 63 5. Cabinet + Frame Installation Samsung Electronics ※ Cabinet Installation to Frame ※ Bridge Box Installation ① Remove the COVER-CONNECTOR and the 2 screws. (Fig.1) ② After Connect 3 cables to the bridge box, install to SET. (Fig.2) Fig.1 ※ Remove 2Point using DELPHINUS or (-) driver.
Page 64 5. Cabinet + Frame Installation Samsung Electronics ※ Cabinet Installation to Frame ※ Bridge Box Installation ③ Assemble the Bracket-Cover. (Fig.3) CUSHION-RUBBER ④ Attach two CUSHION-RUBBER included in the Media Box. (Fig.4) ※ provided by Media Box (For preventing foreign substance penetration) Fig.3...
Page 65 5. Cabinet + Frame Installation Samsung Electronics ※ Cabinet Installation to Frame ① Adjust the Corners of the Cabinet to each of the cravings to be closer to the Frame. (Fig.1) ② Press the upper side of the Frame and assemble so that it slides towards downward.
Page 66 5. Cabinet + Frame Installation Samsung Electronics ※ Cabinet Installation to Frame ③ Install the cabinet at the end of the first floor (Right) (Fig.3-1) ※ Check the vertical and horizontal between the modules (between cabinets) using a laser and a level based on the LED.
Page 67 5. Cabinet + Frame Installation Samsung Electronics ※ Use the Align Jig (Reference) - Align jig is fastened using bracket frame and M4 screws. (Fig.3-2) ※ Check the parallel with the cabinet module using the Align jig. ※ Align jig is a simple reference, the exact standard, use a laser and a horizontal system..
Page 68 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 2. 2nd CABINET CABLE connection - Connect the 3 cables. ① ② DATA AC POWER ③ ※ Connect ① CABLE to HOLDER-WALL. (Same as CABINET 1) AC POWER ※...
Page 69 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 2. 2nd CABINET CABLE connection - Connect DATA CABLE of CABINET 1. (While holding CABINET) - Install to Frame kit. - Adjust Z-leveling between CABINET 1. (refer to p.42~43) ※...
Page 70 5. Cabinet + Frame Installation Samsung Electronics ◇ Adjust Z-leveling between modules. - Each module block can be adjusted its leveling at 8 points . (corner 4point /side 4point) - Follow the below step to adjust the level between modules.
Page 71 5. Cabinet + Frame Installation Samsung Electronics ◇ Adjust Z-leveling between modules. 1. Attach Suction-Pad (Refer to p.107) 2. Move Module 2.0mm 3. Insert Gap-Tool Turn Gap-Tool 90degree 2.0mm Un-Lock Lock ~2mm 90° 5. Hold Module by Hand 4. Insert Adjusment-Tool...
Page 72 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation (Reference) 1. When installing the second cabinet after the first, in order not to collide with the modules, - Push the ①,② module to the side. - Attach Edge Protection Jig V to the edge.
Page 73 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 3. 3rd CABINET CABLE connection - Connect 6 cables. (Fig.1) - Install to Frame kit. - Adjust Z-leveling between CABINET 2. (refer to p.42~43) ① ② DATA AC POWER ※...
Page 74 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 4. 4th CABINET CABLE connection - Connect 3 cables. (Fig.1) - Connect DATA CABLE of CABINET 3. (While holding CABINET) - Install to Frame kit. - Adjust Z-leveling between CABINET 3.
Page 75 5. Cabinet + Frame Installation Samsung Electronics - After installing first row, assemble Cover PCB at bottom line of cabinets. (Refer to p.67~68 for assembly of Cover PCB) - Adjust pixel alignment by fastening screw from Cover PCB. Cover PCB Fig.1 Fastening screw from Cover PCB to adjust pixel alignment...
Page 76 5. Cabinet + Frame Installation Samsung Electronics ◇ Align modules in X,Y direction - Modules are aligned by Cover PCB which attached on boundary area ※ Only do modules alignment after adjust Z-leveling of modules. ① Assemble all Cover PCB to 4 side by screw.
Page 77 5. Cabinet + Frame Installation Samsung Electronics ◇ Align modules in X,Y direction ① Y-axis - Fasten the Holder-Screw to the bottom right Half-cabinet. - Slide the left Half-cabinet to the left to make the gap with right. ※ Fasten the Holder-screw - After checking if the gap with the right side is parallel, with the set up little.
Page 78 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 5. 5th CABINET CABLE connection - Connect 2 cables. ① ② DATA AC POWER...
Page 79 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 5. 5th CABINET CABLE connection - Connect 2 CABLEs of CABINET 1. (While holding CABINET) - Install to Frame kit. - Adjust Z-leveling between CABINET 1. (refer to p.42~43) ※...
Page 80 5. Cabinet + Frame Installation Samsung Electronics ※ Cabinet Installation to Frame - When installing the 2 stage, Check the level by fastening the screw with Align Jig in the same way as the 1 stage installation method. (refer to p.60) (Fig.1)
Page 81 5. Cabinet + Frame Installation Samsung Electronics ◇ Cabinet Installation (Reference) 2. When installing a two-stage cabinet after the first stage installation, - Push the ①,② module to the side. ※ When pushing a module, Use the adsorber. (refer to p.107 ) - Attach Edge Protection Jig V and Protection Jig H to the edge .(Fig.3)
Page 82 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 6. 6~8th CABINET CABLE Connection - Work the same as CABINET 5. - Adjust Z-leveling with surrounding CABINET. (refer to p.42~43) - After install CABINET 8, Assemble the COVER-PCB.
Page 83 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 7. 9~12th CABINET CABLE connection - Connect 2 cables. - Connect the 2 CABLEs of CABINET at the 2 stage below. (While holding CABINET) - After install to Frame kit, Adjust Z-leveling with surrounding CABINET.
Page 84 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET 8. 4 stage CABINET CABLE connection - Connect SENSOR cable. (Only 13,15 CABINET) - Connect the 2 CABLEs of CABINET at the 3 stage below. (While holding CABINET) - After install to Frame kit, Adjust Z-leveling with surrounding CABINET.
Page 85 5. Cabinet + Frame Installation Samsung Electronics ◇ Align modules in X,Y direction - After assemble Cover PCB, assemble Holder PCB. ※ The holder PCB is a device to prevent the expansion between modules. ① After complete all alignment work using the Cover PCB, install Holder.
Page 86 5. Cabinet + Frame Installation Samsung Electronics ◇ CABLE connection when installing CABINET [ 4x4 CABLING]...
Page 87 5. Cabinet + Frame Installation Samsung Electronics ◇ Data cable connection for the 4K screen Connection diagram (Front view)
Page 88 5. Cabinet + Frame Installation Samsung Electronics ◇ Data cable connection for the 6K screen (Front view)
Page 89 5. Cabinet + Frame Installation Samsung Electronics ◇ Data cable connection for the 8K screen (Front view)
Page 90 5. Cabinet + Frame Installation Samsung Electronics ◇ Power cable connection for the 4K screen Rear view AC power cable ※ The AC Power Daisy chain can be connected to the total of four cabinets without 110 / 220V distinction...
Page 91 5. Cabinet + Frame Installation Samsung Electronics ◇ Power cable connection for the 6K screen Rear view AC power cable ※ The AC Power Daisy chain can be connected to the total of four cabinets without 110 / 220V distinction...
Page 92 5. Cabinet + Frame Installation Samsung Electronics ◇ Power cable connection for the 8K screen (Rear view) AC power cable ※ The AC Power Daisy chain can be connected to the total of four cabinets without 110 / 220V distinction...
Page 93 Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 94 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 1. FRAME BEZEL SIDE Installation • Check the distance between the screen and the screen by facing the FRAME BEZEL SIDE on the left / right side of the cabinet.
Page 95 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 1. FRAME BEZEL SIDE Installation • After checking the front part of the BEZEL, check if the bracket corner maintains 90 degrees before and after installation. • Before attaching BEZEL SIDE, Check that whether Holder-Screw is coming out of Cover-PCB, and turn it so that it does not coming out.
Page 96 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 2. Before installation, the FRAME BEZEL TOP / BOTTOM removes the cover cap according to the sensor location and attaches the sensor * The sensors are included in the M-BOX component ACCESSORY as shown.
Page 97 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation * Based on 4x4, there are two COVER-CAPs per cabinet. , As shown, only COVER-CAP at both ends is removed(Do not use it if it is installed in a buried area.
Page 98 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 3. The SENSOR TOP / BOTTOM sensor is the SENSOR part behind the cabinet and USB C type in advance before installing the Bezel. SENSOR TOP/BOTTOM...
Page 99 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Sensor normal operation check test  After TV on, check if the sensor operates normally. - To check sensor operation, move to the menu where real-time sensor data can be read in M-Box - Factory →...
Page 100 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Sensor normal operation check test  Sensor data check The sensor data corresponding to each position is refreshed every 8 seconds and the value changes. - Check if the LUX, CCT, Temp, and Humidity values of each sensor change.
Page 101 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 4. The BRIDGE BOX is connected to the Bluetooth/Wi-Fi, and the BLUETOOTH WIFI unit behind the first cabinet installed. * The BRIDGE BOX decomposes the module of the first cabinet and attaches it to the rear.
Page 102 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 5. If FRAME BEZEL TOP, remove the cover cap at both ends and attach the SENSOR TOP to the possible outside. * Before attaching a sensor, Remove the Stud-Pem of Top Cabinet * When attaching a sensor, assemble it by pressing the hook part.
Page 103 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 6. Even if FRAME BEZEL BOTTOM, remove the cover cap at both ends and attach the SENSOR BOTTOM to the possible outside. * When attaching a sensor, assemble it by pressing the hook part .
Page 104 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 7. In the case of Bluetooth/Wi-Fi sensor module, when installing FRAME BEZEL BOTTOM, it is attached after removing Cover-Cap. * When attaching a sensor, assemble it by pressing the hook part.
Page 105 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 8. Connect BRACKET LINK to the FRAME BEZEL TOP BOTTOM with M3 SCREW. M3,L5 BRACKET LINK...
Page 106 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 9. Place the ASSY FRAME BEZEL TOP BOTTOM on the top left side of the cabinet. • Place the FRAME BEZEL SIDE and FRAME BEZEL TOP BOTTOM so that there is no gap.
Page 107 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 10. Place the ASSY FRAME BEZEL TOP BOTTOM on the upper right side of the cabinet. • Place the FRAME BEZEL SIDE and FRAME BEZEL TOP BOTTOM so that there is no gap.
Page 108 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 11. FRAME BEZEL TOP BOTTOM is fastened using one M3L5 and M4L8 screws. [Fig.1] * When a gap occurs in the middle of the BEZEL, attach the SHEET BEZEL so that the gap is not visible on the front.
Page 109 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel Installation 13. Install the bezel at the bottom of the cabinet in the same way as in the previous steps 8 to * Be careful not to cause a gap between FRAME BEZEL SIDE and FRAME BEZEL TOP BOTTOM.
Page 110 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel extension installation • Vertical Extension - If it is a cabinet of 5 or more stages, the FRAME BEZEL SIDE is extended through the connection of the BRACKET with the M3,L3 screws.
Page 111 6. Cabinet + Frame + Bezel Installation Samsung Electronics ◇ Bezel extension installation • Horizontal Extension - The extension of the FRAME BEZEL TOP BOTTOM in the horizontal direction is the same as the basic installation method. - If it is a screen of a six-row cabinet, connect and install three FRAME BEZEL TOP BOTTOM (2).
Page 112: Disassembly & Front Service
Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 113 7. Disassembly & Front Service Samsung Electronics ① Remove DECO FRAME BEZEL and Cover / Holder PCB. - Remove Deco Bezel As refer to installation manual, Remove BEZEL in order to top → bottom → left/right. M3,L5 M4,L8 M4,L8 - Remove Cover/Holder PCB If the bottom (first stage) is disassembled, the entire four sides are removed.
Page 114 7. Disassembly & Front Service Samsung Electronics ② Remove the sensor of DECO FRAME BEZEL. (Installation Manual reference) - Remove sensor (press the hook part out)
Page 115 7. Disassembly & Front Service Samsung Electronics ② Secure the GAP around the Half-Cabinets to be replaced using the adsorber. ※ Refer to the next page of how to use the adsorber Push cabinets toward outside to get 2mm gap that located on same vertical line with repairing Half- cabinet.
Page 116 7. Disassembly & Front Service Samsung Electronics ※ Using Absorber ㅁ Absorber Handle type tool that fixed on cabinet front side(LED side) to prevent damage to LED Modules while assembly/disassembly, moving half-cabinets. Un-Lock Lock ※ grasp as direction of push or pull.
Page 117 7. Disassembly & Front Service Samsung Electronics ③ Attach the Edge Protection. - Insert GAP Tool at middle of Top/Bottom edge of half-cabinet to fix gap. (Fig.1) - Attach edge protection to repairing half-cabinet and remove GAP Tool. (Fig.2) A/S-ASSY GAP TOOL ★...
Page 118 7. Disassembly & Front Service Samsung Electronics ④ Separate the Half-Cabinets with the Module Separation JIG. - Attach the module separation jig to the Half-Cabinet to be replaced. (Fig.1) - Turn the T-JIG to separate the Half-Cabinets from 10 to 15 cm. (Fig.2)
Page 119 7. Disassembly & Front Service Samsung Electronics ⑤ Remove cable and disassemble Half-Cabinet. - Attach the Module Separate Jig to the Half-Cabinets and slightly lift it. And remove the cable connected. ※ Leave edge protection attached for assembly of the new Half-Cabinet...
Page 120 7. Disassembly & Front Service Samsung Electronics ※ Using PLIER JIG ※ There is a groove that takes locking on the top head A/S-ASSY PLIER JIG ※ Locking can slip if it does not get to the groove correctly (BN81-17541A) ■...
Page 121 7. Disassembly & Front Service Samsung Electronics ⑥ Replace with the new Half-Cabinets. ※ New cabinet must be changed after conduct Dehumidifying mode Aging. Remove Cover corner from Buffer Cabinet laid on the floor and lift up half-cabinet with Separate JIG.
Page 122 7. Disassembly & Front Service Samsung Electronics ※ Locking replaced Half Cabinet magnets ※ The Wall Pro is also used for UNLOCK, but The Wall Lux only uses LOCK. ※ The Wall Lux model uses the module separation jig to separate the module without UNLOCK.
Page 123 7. Disassembly & Front Service Samsung Electronics ※ Rear side of half-cabinet ※ Remove and Change TCON Board ① Remove screw of Cover Terminal and TCON Board. ② Remove cable of TCON Board. (Master/Slaver same) ※ FFC Cable C/Terminal Screw point Lift up lock and pull out to remove cable.
Page 124 7. Disassembly & Front Service Samsung Electronics ※ Remove and Change TCON Board ④ Remove TCON Board and replace New one. ⑤ Assembly is reverse order of disassembly. ※ After assembling the power cable first, make the FFC cable work on it.
Page 125 7. Disassembly & Front Service Samsung Electronics ※ Module (Half-cabinet Module) Store & Packaging ① Repairing Half-cabinet should be stored with buffer cabinet. Dissemble Half-Cabinet from existing Buffer Cabinet, Change it with Repairing Half-cabinet.(Fig.1) ② Repairing Half - Cabinets will be packed and changed by a service engineer and SI vendor.
Page 126 7. Disassembly & Front Service Samsung Electronics ※ Module (Half-cabinet Module) Store & Packaging ③ Remove repairing half-cabinet from stored buffer cabinet. (Fig.2) ④ Package Half-cabinet in The Wall LED Module BOX. (Fig.3) ※ The Wall LED Module BOX ※ Remove repairing half-cabinet from buffer cabinet ※...
Page 127 7. Disassembly & Front Service Samsung Electronics ※ SMPS disassembly ① Remove two COVER-REAR SUBs. Push the Hook and pull out.
Page 128 7. Disassembly & Front Service Samsung Electronics ※ SMPS disassembly ② Remove two Power CABLEs. POWER OUT CABLE POWER IN CABLE...
Page 129 7. Disassembly & Front Service Samsung Electronics ※ SMPS disassembly ③ Remove screws over the insulator on SMPS. (6EA) SMPS 1 ※ Remove the double face tape. SCREW-TAPTYPE SCREW-TAPTYPE [6003-000365] [6003-000365] (M3,L8) (M3,L8) SCREW-MACHINE [6001-002789] (M4,L6)
Page 130 7. Disassembly & Front Service Samsung Electronics ※ SMPS disassembly ★ Caution ★ ④ Remove the CABLE connected to the SMPS. Be careful of falling SMPS down when removing from SMPS shield. ⑤ Assembly is done in reverse order. ※ Hold Cable and SMPS ※...
Page 131 7. Disassembly & Front Service Samsung Electronics ◆ SMPS Discharging The possible area to touch : - When you touch or take off SMPS, you must check to discharge The possible area to touch without additional discharging two discharging point using JIG...
Page 132 7. Disassembly & Front Service Samsung Electronics ※ BRACKET-FRAME disassembly ① Separate two Half-Cabinet to be separated and four Half-Cabinet of CABINET above / below. (Fig.1) ※ Refer to Half-Cabinet Disassembly Method ② Remove the four BRACKET-PLATE of the FRAME to be separated and the upper CABINET. (Fig.2) ※...
Page 133 7. Disassembly & Front Service Samsung Electronics ※ BRACKET-FRAME disassembly ③ Turn the four BOLT-ETC of the FRAME to be separated ※ Use (-) driver and turn it slightly and pull it forward. (clockwise direction) ※ At this time, the upper BOLT-ETC of the following FRAME is also turned to pull a little forward.
Page 134: Media Box Installation And Connection
Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 135 8. Media Box Installation and Connection Samsung Electronics • Media Box Input / Output Front view Port Description Turn the product on or off. USB 2.0 Connect to a USB memory device. Rear view Port Description Port Description ONE CONNECT(L1, L2, L3, L4) Connects to a cable using an LC fiber cable.
Page 136 8. Media Box Installation and Connection Samsung Electronics • Media Box Installation Precautions ① Product recommend installing this product in a standard 19-inch server rack. ※ The product has a built-in fan, which can cause noise at the level of a high performance game machine.
Page 137 8. Media Box Installation and Connection Samsung Electronics • Media Box Connection ① Input the video signal to the Media Box. (Input terminal : HDMI) ② Connect from the One Connect port of Media Box to WDM Rx port of Cabinet by using Optical Cable.
Page 138 8. Media Box Installation and Connection Samsung Electronics • Connecting optical cable according to screen layout (4K, 6K, 8K) - The screen must be extended from the bottom to top left  right 8K : 7680 x 4320 6K : 5760 x 3240 4K : 3840 x 2160 ※...
Page 139 8. Media Box Installation and Connection Samsung Electronics • Connecting optical cable according to screen layout (3K) 3K : 2880 x 1620...
Page 140 8. Media Box Installation and Connection Samsung Electronics • Connecting optical cable according to screen layout (5K) 5K : 4800 x 2700...
Page 141 8. Media Box Installation and Connection Samsung Electronics • Connecting optical cable according to screen layout (7K) 7K : 6720 x 3780...
Page 142 8. Media Box Installation and Connection (21:9) Samsung Electronics • Connecting optical cable according to screen layout 8(H)x6(V) : 7680 x 3240 6(H)x4(V) : 5760 x 2160 Cabinet front view 광케이블은 항상 전면기준 우측에 있는 케비넷에 연결되어야 함...
Page 143 8. Media Box Installation and Connection (21:9) Samsung Electronics • Connecting optical cable according to screen layout 7(H)x5(V) : 6720 x 2700...
Page 144 8. Media Box Installation and Connection (21:9) Samsung Electronics • How to change the display ratio (16:9 ↔ 21:9) When you install the Wall screen as 21:9 ratio, you can change the display ratio to 21:9 or 16:9 by below method.
Page 145 8. Media Box Installation and Connection Samsung Electronics • Between Media Box and Cabinets ① Optical cable connection - Connect the optical cable from the One Connect to module Rx One port of One Connect Module Rx [Optical cable insertion status...
Page 146 8. Media Box Installation and Connection Samsung Electronics ② Instruction for handling Optical Cable  Use BIMMF, OM3, LC-LC connector type optical cable for stability of operating * BIMMF (Bend Insensitive Multimode Fiber) ★ Unusable : Single Mode, OM1, OM2 type ...
Page 147 8. Media Box Installation and Connection Samsung Electronics ③ Cable connection  Connecting a connector, special attention is required. It’s a common cause of malfunction.  If Duplex type, unlock the locking structure and connect one by one like Simplex type.
Page 148 8. Media Box Installation and Connection Samsung Electronics ③ Cable connection  Remove the dust protection cap and connect the cable as below picture  Insert with weak force until it sounds “Click”  Keep the dust protection cap well for reuse.
Page 149 8. Media Box Installation and Connection Samsung Electronics ③ Cable connection  Check it whether the cable is inserted well.  Install the optical cable carefully. The optical cable does not have the tension of the upper/lower and the left/right.
Page 150 8. Media Box Installation and Connection Samsung Electronics ③ Cable connection  When you remove the cable, press the detach clip to remove it. Do not just pull the cable as below.  Do not force the optical cable by pulling it up and down.
Page 151 8. Media Box Installation and Connection Samsung Electronics ④ Instruction for handling Optical Cable  Consider the pulling force so that the minimum force is applied to the optical fiber when installing the cable (Refer to each cable specification ) ...
Page 152 8. Media Box Installation and Connection Samsung Electronics ④ Instruction for handling Optical Cable  Gently fix the optical cable to prevent direct compression when fixing it to Tray and so on. Tighten the clamp Clamp tightening properly Fixed soft material...
Page 153 8. Media Box Installation and Connection Samsung Electronics ① Instruction for handling HDBaseT (HDBT) cable ★ Orderly Rolled (Recommend) Random Rolled ★ (Not Recommend)  Do not use “comb” or “pinstripe” cable  Use HDBase-T cables with 15 meter long at minimum and 100 meter long at maximum.
Page 154 8. Media Box Installation and Connection Samsung Electronics ② Finishing method for HDBase-T Cable  STP RJ45 shielded Plug. RJ45 Connector should be CAT6 or CAT7 shielded RJ45 and load bar.  Load bar Load bar and Drain wire Wires aligned with Load bar ⑩...
Page 155 8. Media Box Installation and Connection Samsung Electronics • Bridge Box connection (When connecting Bluetooth/Wi-Fi Module) - Three cables are connected to the Bridge Box. (HDBaseT cable, Bluetooth/Wi-Fi cable, 24pin system cable) [Media Box] 24pin system Cable HDBaseT Cable Bridge Box...
Page 156 8. Media Box Installation and Connection Samsung Electronics • Multi Brand Remote ■ IR LED Location and Radiation angle - High power IR LED, 4EA - Front : 3EA, Rear 1EA (Angle ±30°) → One of the Front LED 1EA is 45° Tilting (Improved radiation coverage)
Page 157 8. Media Box Installation and Connection Samsung Electronics • Multi Brand Remote - Rack type [Total opened type] [Total closed type] [Partially sealed type ] - Multi Brand Remote operation according to rack type Total closed type Partially sealed type...
Page 158 8. Media Box Installation and Connection Samsung Electronics • Multi Brand Remote ■ In a partially sealed rack, the case of Multi Brand Remote does not work - The surrounding of the two devices are different that means light emitting part is opened and receiving part is closed.
Page 159 8. Media Box Installation and Connection Samsung Electronics  Factory menu for Service - Installation and Service engineers can monitor the product status in the factory menu and change initialization and settings. - The only menu for the Wall product is in “ The Wall Option “. (Control > The Wall Option) - How to enter Factory menu : .
Page 160 • Media Box Connection (Panel Configuration) - Media Box Picture Setting • The default picture configurations are optimized for The Wall cabinet in Samsung factory. • The picture configurations will be configured automatically when you finish the installation. • For the best picture quality, Please connect Media Box and LED displays via LSM software properly.
Page 161 8. Media Box Installation and Connection Samsung Electronics • Media Box Connection - Note after connecting to Media Box and LSM - Release built-in pattern for cabinet installation after connecting to Media Box and LSM . Cause : If you don’t display the built-in pattern, SEAM adjustment and cable connection status cannot be confirmed.
Page 162 7. Media Box Installation and Connection Samsung Electronics • Internet Connection(Configuration) - Media Box can be connected to a user Access Point by wired and wireless. User’s Internet connection is as below. . Recommend wired connection as possible. - Media Box receives IP from DHCP with user Access Point or User can set it himself.
Page 163 8. Media Box Installation and Connection Samsung Electronics • Internet Connection (Menu selection) ① Wired (Ethernet) connection Menu ② Wireless (Wi-Fi) connection Menu...
Page 164 8. Media Box Installation and Connection Samsung Electronics • LSM Connection 연결 (Configuration) - LSM PC and Media Box can be connected in two ways: ① wired and ② wireless (WiFi) - Wired : Ethernet cable can be connected between Media Box and LSM PC.
Page 165 8. Media Box Installation and Connection Samsung Electronics • LSM Connection (Configuration) - LSM PC and Media Box can be connected in two ways: ① wired and ② wireless (WiFi) - Wireless(WiFi) : The distance between Media Box and LSM PC is far (100m) or It’s difficult to connect with Ethernet cable .
Page 166 8. Media Box Installation and Connection Samsung Electronics • LSM WiFi Connection (Configuration) - 무선연결 : ② Check the SSID that can be connected by Wi-Fi on LSM PC. ③ The SSID is the device name of the Media Box. Connect to SSID of Media Box (Password : samsungwall) (Media Box MenGeneral ...
Page 167 Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 168 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Download Path : SLM – Help – Download Center -"LED SIGNAGE MANAGER" or "LSM“ • - SLM : https://www.secslm.com...
Page 169 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Start– Login Page • The login screen appears when LSM is launched for the first time. To set a password and provide access to specific users to ensure security, enter a password and click Start.
Page 170 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) New Connection • To connect by manually specifying a desired Media Box, enter IP address “192.168.176.50”. (Media Box uses a fixed IP address to communicate with...
Page 171 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) New Connection – Setup and Connect • 8 Cabinet Groups appear to set Cabinet IP address. * Model type : “The Wall Luxury” Select Enter IP address for each groups.
Page 172 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) [Caution !!] TCP port 1515, 48484, 48485 and 58585 is used between Media Box and LSM communication. Main Window – Home Window Check your network, firewall and security settings to use it.
Page 173 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Main Window – Edit Connection – Layout Window • Connection layout: Control position and layout of LED Cabinets. Feature View: Auto align, Layout Import/Export, Edit Connect to edit connect information.
Page 174 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Main Window – Connections Window • Device connection list view: Media Box nodes, Edit/Delete Media Box connection, Each Cabinet groups to be controlled. Connection layout (View Port):...
Page 175 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Main Window – Connections Window – Device Information / Settings View • 1. Media Box Settings . Media Box Software Update FPGA and Valens firmware version can be updated.
Page 176 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Main Window – Connections Window – Device Information / Settings View • 3. Cabinet Calibration . Cabinet Calibration └ Cabinet RGB CC : Correct the RGB CC matrix of Cabinet └...
Page 177 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Main Window – Connections Window – Sub Information View • 1. Monitor Window : . Tracking log, Log export to file 2. LED Signage Cabinet .
Page 178 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Main Window - Preferences • Options Command Retry Count Error Status Interval (Default 30 min.) Set Temperature to alert Support Languages of program Log management (Back-up, delete)
Page 179 9. LSM Settings & Instructions Samsung Electronics 9-1. Control Program for PC LSM(LED Signage Manager) Main Window – LED Cabinet Dehumidification • Check Dehumidification icon on Media Box node. Click it to start dehumidification. Elapsed time is displayed on LSM.
Page 180 9. LSM setting & directions for use Samsung Electronics 9-2. Calibration ■ On-Site Calibration S/W - Provides calibration function using Measuring equipment (Colorimeter) / Mobile - Adjustment of module units : visual adjustment -> Automate with S/W - Provides Module / Half Cabinet / Cabinet / Screen Calibration function...
Page 181 9. LSM setting & directions for use Samsung Electronics 9-2. Calibration ■ On-Site Calibration S/W using Measuring equipment (Colorimeter) - After installing Calibration S/W on your PC & connecting Measuring equipment , select Reference / Target Module to perform calibration.
Page 182 9. LSM setting & directions for use Samsung Electronics 9-2. Calibration ■ On-Site Calibration S/W using Mobile - Install calibration software app in mobile and run it to connect network - Calibration unit selection : Module or Cabinet - Select “ Reference & Target “...
Page 183 9. LSM Settings & Instructions Samsung Electronics 9-3. Trouble shooting for LSM  Network problem between LSM and Media Box ① In case LSM can`t search Media Box or Disconnected message is displayed. -. Check Ethernet cable. -. Check IP address of Media Box (192.168.176.50 is the IP address of Media Box) -.
Page 184 9. LSM Settings & Instructions Samsung Electronics 9-3. Trouble shooting for LSM Factory reset In case the screen order is displayed abnormally despite the correct cable connections, there may be a master cabinet in the middle of the connections. Do Factory reset according to following guide. After that, delete the previous connected Media Box in LSM and connects it again.
Page 185 Samsung Electronics 1. Product information and precautions for installation 2. Check point about the radiant heat 3. Frame installation 4. Preparation for cabinet installation 5. Cabinet + Frame installation 6. Cabinet + Frame + Bezel installation 7. Disassembly & Front Service 8.
Page 186: How To Use The Wall
- Initial Screen will be displayed on middle fit size that show special feature. - Smart Control will be paired automatically. ∙ If not paired, press and hold return and play button simultaneously. - Set up Network, Terms, Samsung Account and etc. - OOBE via Mobile is not supported. [How to pair Remote]...
Page 187 - Mandatory Terms : To use Smart Hub(Neflix, Youtube etc), it should be agreed ∙ A kind of the mandatory Terms : Terms and Conditions, Samsung Privacy Policy ∙ Only China : Mandatory Terms + Use of Sensitive Personal Data (个人信息收集使用同意书) - Optional Terms : To use specific feature(Voice), ∙...
Page 188 - Google Account : Skip - Google Service : Accept - Review Additional Apps : Install Default Apps - Samsung Account : Skip (After Initail Setup, Input SA through Galaxy Store App) ∙ It is best to input the end-user’s account - End...
Page 189 10. How to use The Wall - Initial Setup Sequence for Tablet Samsung Electronics Start  Select Arrow Button below Start...
Page 190 10. How to use The Wall - Initial Setup Sequence for Tablet Samsung Electronics Connect to Wi-Fi  Setup for Wi-Fi connection - Select AP and Input Password if needed - Choose Next...
Page 191 10. How to use The Wall - Initial Setup Sequence for Tablet Samsung Electronics Agree to the Terms and Conditions  Terms and Conditions - Select only mandatory items and scroll down - Next...
Page 192 10. How to use The Wall - Initial Setup Sequence for Tablet Samsung Electronics Google Account  Skip...
Page 193 10. How to use The Wall - Initial Setup Sequence for Tablet Samsung Electronics Google Services  Leave Default Options - Scroll down and Select Accept...
Page 194 10. How to use The Wall - Initial Setup Sequence for Tablet Samsung Electronics Review Additional Apps  Install all Default Apps...
Page 195 10. How to use The Wall - Initial Setup Sequence for Tablet Samsung Electronics Samsung Account Sign in  Setup for Samsung Account - Skip...
Page 196 10. How to use The Wall – Samsung Galaxy App Store Samsung Electronics Update for Galaxy App Store  Update Galaxy Apps to Galaxy Store Select Update Agree to Terms and Conditions Update...
Page 197 - App Update(Recommendation) ∙ Galaxy App -> Galaxy Store - Log-in with Samsung Account ∙ CI should prepare a Samsung Account for end-user before delivering tablet ∙ Generation of Samsung Account : https://account.samsung.com ∙ A ID/Password should be delivered to End-user by e-Mail or Document ∙...
Page 198 ④ Entertainment mode / Ambient mode ⑤ Using Entertainment browser ⑥ Using Ambient browser ⑦ Using Bixby ⑧ Using other smart features ⑨ Connecting the Tablet ⑩ Tablet UX Guide How to play contents on Samsung The Wall Screen How to create MY W EDITION...
Page 199 When you turn on Samsung The Wall for the first time, the Samsung Smart Remote pairs automatically. If the Samsung Smart Remote does not pair automatically, point it at the remote control sensor of The Wall, and then press and hold the...
Page 200 10. How to use The Wall – Quick Guides for Using The Wall Samsung Electronics ② Using the Samsung Smart Remote Power Turns the power on and off Bixby If you release the button after you press the button and speak the desired command, you can recognize the contents of the user on the TV and execute the function.
Page 201 ③ TV OOBE(Out of Box Experience) 1) Select language 2) Connection Guide 3) Setup Network 4) T&C,PP,PN 5) Samsung Account (optional) 6) Zip code(Location) 7) Identifying Your Devices(Device auto detection) 8) Setup TV & Device Summary 9) Make your Smart Hub...
Page 202 ④ Entertainment mode / Ambient mode Samsung The Wall has two modes. Entertainment (TV) mode is a traditional TV experience of watching TV / VOD content. Ambient mode allows you to display your photos in the Art content or My W edition that blends in with your surroundings while you are not looking at the content for the Lifestyle feature.
Page 203 10. How to use The Wall – Quick Guides for Using The Wall Samsung Electronics ④ Entertainment mode / Ambient mode Entertainment Screen (Zoom out) MY W EDITION Browsing Screen (Entertainment/Ambient mode) Entertainment Screen (Zoom in) MY W EDITION (Zoom in) or Ambient contents...
Page 204 10. How to use The Wall – Quick Guides for Using The Wall Samsung Electronics ⑤ Using Entertainment browser You can quickly and easily reuse your favorite apps or previously run apps by launching your browser by pressing the button once more on the content watch screen.
Page 205 10. How to use The Wall – Quick Guides for Using The Wall Samsung Electronics ⑥ Using Ambient browser When you watching Ambient contents, You can browse the contents by setting the Ambient mode contents by pressing the button once more.
Page 206 Samsung Electronics ⑦ Using Bixby You can control the TV by voice commands on the Samsung Smart Remote. Samsung The Wall must be connected to the Internet to use Bixby. Supported features may vary depending on your Samsung account login.
Page 207  Attention) When you connect to Samsung Sound bar model . Some dedicated features of Samsung sound bar can’t be possible to work according to the device name setting in The Wall . Change the device name setting to what is compatible with Samsung sound bar model.
Page 208 - Before launching the tablet app, Samsung The Wall's initial setup must first be completed. 2. When you launch the tablet app, it automatically tries to connect with Samsung The Wall. - Wi-Fi settings are required to connect to Samsung The Wall.
Page 209 Option buttons - Menu (Settings) - Sources - Remote controller Status panel - Power(When The Wall is off) - Now on Samsung The Wall Global buttons - Zoom - Create Background Material screen Preview Browser - Contents which is selected launcher...
Page 210 EDITION. - Change content options as color, or set background options. - MY W EDITION and MY Collection require sign in to Samsung Account, and the picture content on Ambient of The Wall Screen is linked according to the account that is logged into the tablet.
Page 211 1. Select the app on Launcher and you can see browser for contents preview. 2. To open the app on The Wall Screen, select the Open app on Samsung The Wall button. 3. To play content directly on The Wall Screen, select the SEND TO SAMSUNG THE WALL button.
Page 212 2. To create your own MY W EDTION with photos pressing CREATE MY W EDITION button. - Samsung Account sign in is necessary to create MY W EDITION. - You can not complete My W edition while running the app on Samsung The Wall.
Page 213 Select the left photo frame, edit the photo details. My W edition is applied to Screen and saved. • • When you're done editing, click Save to finish. Select [Send to Samsung The Wall] to view it on the wall • • screen.
Page 214 10. How to use The Wall – Quick Guides for Using The Wall Samsung Electronics  Edit style & setting Create Background Material Style & Setting / Create Wall Material - You can change MY W EDITION’s style & setting.

This manual is also suitable for:

Lh008iwr

Samsung SBB-MBOXR48 Installation Manual

Quick Links

Related Manuals for Samsung SBB-MBOXR48

Summary of Contents for Samsung SBB-MBOXR48

This manual is also suitable for:

Table of Contents