Samsung LH025IFH AS Series Installation Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. LH025IFH AS Series
  6. Installation manual
Samsung LH025IFH AS Series Installation Manual

Samsung LH025IFH AS Series Installation Manual

Led display
Hide thumbs Also See for LH025IFH AS Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Samsung Electronics
LED Display
Installation Manual
Ver 3.0
LH015IFH*AS (P1.5)
LH020IFH*AS (P2.0)
LH025IFH*AS (P2.5)
SBB-SNOWJ3U
SBB-SNOWJMU

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LH025IFH AS Series and is the answer not in the manual?

Questions and answers

Related Manuals for Samsung LH025IFH AS Series

Summary of Contents for Samsung LH025IFH AS Series

  • Page 1 Samsung Electronics LED Display Installation Manual Ver 3.0 LH015IFH*AS (P1.5) LH020IFH*AS (P2.0) LH025IFH*AS (P2.5) SBB-SNOWJ3U SBB-SNOWJMU...

  • Page 2: Revision History

    Revision History Samsung Electronics Version Date (Y/M/D) Description 2020/03/20 New Release 2020/06/19 Add SNOW1810U installation and Picture Setting 2020/08/07 Add Test Pattern function 2020/11/02 Modify dehumidification guide 2020/11/16 Add Network IP Setting by USB 2020/11/27 Update LSM guide 2020/12/01 Update Dehumidification Guide...

  • Page 3: During Installation

    ∙ Case when vacuum packaging is already unsealed before unpacking products. ∙ Case when environment condition is worse than Samsung working condition (0°C~40°C/10~80%RH). ∙ Case when it elapses longer than 7 days after unpacking them, even though the environment condition satisfies Samsung working condition (0°C~40°C/10~80%RH).
  • Page 4 Please print this page and hand it to user. Dehumidification guidance – during installation Samsung Electronics  How to install the screen in the case that dehumidification is necessary ※ Before finishing the directions explained in next pages, never play other contents or use them.
  • Page 5 This contents must be noticed to customer. Please print this page and hand it to user. Dehumidification guidance – during installation Samsung Electronics  How to install the screen in the case that dehumidification is necessary. 3. While installing cabinets, S-Box should play only this pattern.

  • Page 6: During Operation

    Please print this page and hand it to user. Dehumidification guidance – during operation Samsung Electronics • Electrical short in package is possible to happen during products are working. • For keeping quality of products during installation, please refer below cautions.
  • Page 7 Please print this page and hand it to user. Dew condensation due to overcooling Samsung Electronics  Even though meet with Samsung recommended operation condition, dew condensation is possible to happen when surface of products is colder than environment temperature or hot &...
  • Page 8 Please print this page and hand it to user. Prevent condensation due to A/C Samsung Electronics  Make sure that the cold air does not blow directly on the screen. – When the cold air from A/C (air conditioner) blows directly onto the screen surface, condensation may occur depending on the ambient humidity and temperature of screen surface.
  • Page 9 Guidance of latest firmware Samsung Electronics  When install products, please update latest firmware on online - You can download latest firmware from SLM site. ∙ URL of SLM Page : https://www.secslm.com ∙ After login  Help  Download Center에서 Download ∙...
  • Page 10 Check first before Installation Samsung Electronics • All Power cables and OCM cable must be connected firmly • Use *STP, *FTP CAT6 or higher spec cable designed for HDBT transmission, which length is about 15 ~ 100m for HDBT signal stability.

  • Page 11: Table Of Contents

    Table of Contents Samsung Electronics 1. Product Information and Precautions for Installation 2. Check Point about the Radiant Heat 3. Preparation for Cabinet Installation 4. Frame Installation 5. Cabinet + Frame Installation 6. SBOX Installation and Connection 7. Settings and How to Use 8.

  • Page 12: Product Information And Precautions For Installation

    1. Product Information and Samsung Electronics Precautions for Installation ◇ Frame Kit Composition Refer to Page 27 Frame Kit Composition Note FHD Installation VG-LFH15FWA (18 Set) for P1.5 Standard FHD Installation VG-LFH20FWA (32 Set) for P2.0 Standard FHD Installation VG-LFH25FWA...
  • Page 13 1. Product Information and Samsung Electronics Precautions for Installation • Precautions for Installation (LED Physical damage) Precautions Images [ Beware of Outside Impact, Fall] ① Beware not to cause any impact on the LED screen or drop the product on the floor MODULE after the protection gets taken off for installation.
  • Page 14 1. Product Information and Samsung Electronics Precautions for Installation • Precautions for Installation (LED Chemical damage) Precautions Images [Beware of LED Damage due to chemicals] ▶ Beware not to contact the following materials with the product, and minimize CARPET exposure of the product to their vapor...
  • Page 15 1. Product Information and Samsung Electronics Precautions for Installation • Preparations for Installation LED MODULE JIG (-) (+) Driver Electric Driver (model name: CY-LJFNAS) 10.0mm Wrench Service JIG Plier Antistatic Holder Magnet Tool (BH81-00001A) Glove...

  • Page 16: Check Point About The Radiant Heat

    Written under ‘Video, (back light 10)’ standard  Standard and condition for indoor installation - Standard for using ‘SAMSUNG WALL MOUNT’ (Fulfill ADA) ※ ADA(American’s with Disabilities Act ∙ The gap between the front of a product and a wall: 90mm ∙...
  • Page 17 2. Check Point about the Radiant Heat– without Fan Samsung Electronics  Minimum spacing for wall mounting installation Min condition : 30mm (set ~ ceiling) Recommended condition : more than 500mm Air vent area (more than 60% Air vent area...
  • Page 18 2. Check Point about the Radiant Heat– without Fan Samsung Electronics  Minimum spacing for processed installation Min condition : 0mm (set ~ ceiling) Recommended condition : more than 500mm Air vent area Essential cond. : more than 30mm of 100% opening rate Essential cond.
  • Page 19 2. Check Point about the Radiant Heat Samsung Electronics ◇ Axial FAN(selection example) 95 CFM 80 CFM 65 CFM No need for FAN No need for FAN ※ Example) Total CFM? (Outdoor temperature 30℃ , Cabinet (5x5) on condition.) Total 400 CFM →...
  • Page 20 2. Check Point about the Radiant Heat Samsung Electronics ◇ FAN Using condition ◇ Vent specification - Air Vent : install at bottom  Using over 70% open ratio vent ���� ���� ���� ���� ��������. �������� ���������������� ℎ�������� ���� - Top: Seal except fan hole ����...
  • Page 21 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and FAN allocation for wall mounting installation Min condition : 30mm (set ~ ceiling) Recommended condition : more than 500mm Other parts except for FAN...
  • Page 22 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and fan allocation for recessed installation Min condition: 0mm (set ~ ceiling) Recommended condition : 500mm Essential cond. : more than 30mm of 100% opening rate...
  • Page 23 2. Check Point about the Radiant Heat– with Fan Samsung Electronics  Example of minimum spacing and placement during rear exhaust Ambient temperature on the back of the wall should be less than 30 ℃. Other parts except for FAN should be sealed.
  • Page 24 2. Check Point about the Radiant Heat Samsung Electronics  IFH P1.5 (under 25℃) Guidance ※ SAMSUNG WALL MOUNT , Full white, back light 7, VENT 70% No Fan No Fan Rows...
  • Page 25 2. Check Point about the Radiant Heat Samsung Electronics  IFH P1.5 (25~30℃) ※ SAMSUNG WALL MOUNT , Full white, back light 7, VENT 70% 95 CFM 80 CFM 65 CFM No Fan No Fan Rows...
  • Page 26 2. Check Point about the Radiant Heat Samsung Electronics  IFH P2.0 (under 25℃) ※ SAMSUNG WALL MOUNT , Full white, back light 7, VENT 70% No Fan No Fan Rows...
  • Page 27 2. Check Point about the Radiant Heat Samsung Electronics  IFH P2.0 (25~30℃) ※ SAMSUNG WALL MOUNT , Full white, back light 7, VENT 70% 150 CFM No Fan No Fan Rows...
  • Page 28 2. Check Point about the Radiant Heat Samsung Electronics  IFH P2.5 (under 25℃) ※ SAMSUNG WALL MOUNT , Full white, back light 7, VENT 70% No Fan No Fan Rows...
  • Page 29 2. Check Point about the Radiant Heat Samsung Electronics  IFH P2.5 (25~30℃) ※ SAMSUNG WALL MOUNT , Full white, back light 7, VENT 70% 190 CFM 170 CFM 150 CFM 130 CFM No Fan No Fan Rows...

  • Page 30: Preparation For Cabinet Installation

    3. Preparation for Cabinet Installation Samsung Electronics • Preparations Before Installation ① Remove the Box tape at the upper area and then open up the box. (Fig.1) ② Remove the Top–Cushion and hold the handle inside PE-Bag and pull out the set then remove PE bag.
  • Page 31 3. Preparation for Cabinet Installation Samsung Electronics ⑤ Check whether there is any abnormality on the screen by connecting the power cable .(Fig.4) * Do not turn on the white pattern over 10 seconds ※ Refer to the next page how to check abnormality on the screen.
  • Page 32 ※ Do not turn on OR display white pattern more than 10 second . 3. Preparation for Cabinet Installation Samsung Electronics ④ Push ‘Switch Button’ and hold it for ◈ Reference : Process of Screen check more than three seconds.
  • Page 33 3. Preparation for Cabinet Installation Samsung Electronics ⑧ Attach the PET Sheet and assemble Cover PCB for the Cabinet that is located at the exterior. (Blue area at the exterior of Fig.1) ※ PET Sheet & Cover PCB should be at the boundary of whole screen.

  • Page 34: Frame Installation

    4. Frame Installation Samsung Electronics ① Check Frame Kit Composition. VG-LFH15FWA VG-LFH20FWA VG-LFH25FWA Item 10X5 Units Units Units ASSY BRACKET SIDE ⓐ ASSY BRACKET MIDDLE ⓑ ⓒ ASSY BRACKET CENTER ASSY BRACKET JIG ⓓ ASSY SLIDING SCREW ⓔ ASSY ANCHOR SCREW ⓕ...
  • Page 35 4. Frame Installation Samsung Electronics ② Put the ⓐBracket Side the end of the left side and then fasten the screws to install. (Fig.3) ※ After fastening one(1) screw, use the device for vertical positioning to set up straight vertical alignment. Then fasten up the remaining holes.
  • Page 36 4. Frame Installation Samsung Electronics ※ Precautions for Fastening the Screws...
  • Page 37 4. Frame Installation Samsung Electronics ③ Install ⓑBracket Middle. Wrong Installation(X) Correct Installation(O) ※ First, check the Hole to fix the ⓒ JIG. [Fig.1] Wall ※ Second, Mount the ⓒ JIG inside the Bracket Hole and fasten up four(4) Screws [Fig.2] ⓐ,ⓑ,ⓒ...
  • Page 38 4. Frame Installation Samsung Electronics ※ When installing three or more ASSY BRACKETs, adjust their levels because they may be distorted by walls or structures. – After installing three or more ASSY BRACKETs, place another ASSY BRACKET horizontally on them and measure if there is a height difference among them.
  • Page 39 4. Frame Installation Samsung Electronics ⑤ After installing Bracket Center, install cabinets on the bottom line.. [Fig.6] ⑥ When the cabinet installation is finished, slide the LED modules toward the center and check the flushes between the cabinets and the LED modules at both ends.
  • Page 40 4. Frame Installation Samsung Electronics After installing FRAME SIDE 1EA and FRAME MIDDLE 2EA based on VG-LFH15FWA, install the FRAME CENTER. Before installing the FRAME CENTER next FRAME MIDDLE, make sure to install the CABINETs in the bottom line. Slide the LED modules toward the center and check the flushes between the cabinets and the LED modules at both ends.

  • Page 41: Cabinet + Frame Installation

    5. Cabinet + Frame Installation Samsung Electronics • Fix I/G Location ① Install I/G first on the back side of the Cabinet of each Type (Fig.1) ※ Location to Install: Locate the I/G at the point 35~40mm below, which is the standard for carving at the right side of the frame, and then fasten the screws.(Fig.2)
  • Page 42 5. Cabinet + Frame Installation Samsung Electronics ② Adjust the Corners of the Cabinet to each of the cravings to be closer to the Frame. ※ Order of Cabinet Installation (27 Page Fig. 1) ※ Check whether all the four(4) bolts are put into the frame. (Fig.1) ③...
  • Page 43 5. Cabinet + Frame Installation Samsung Electronics ⑤ If modules are too tight, it could be difficult to pick out. During the installation process, select some modules and make sure they are easily picked out and reassembled.
  • Page 44 5. Cabinet + Frame Installation Samsung Electronics ◇ Protection of I/G  To prevent unexpected removing IG box, the Protection Bracket should be attached on left / right side of the display (Fig.1) * In case of pocket installation, do not need to attach the protection.
  • Page 45 5. Cabinet + Frame Installation Samsung Electronics ◇ Installation Guide of recessed screen  When installing recessed screen, minimal work space is needed from the edge of the screen. – In order to finish seam adjustment, fixation parts should be installed on the screen edge. If the parts are not installed, seam between modules could be made.
  • Page 46 5. Cabinet + Frame Installation Samsung Electronics ◇ Installation Guide of recessed screen  Work space should be finished with detachable material for service. – Work space more than 1mm should be secured for safety of the screen. Be cautious of safety of the screen while detaching and attaching finishing material.

  • Page 47: Sbox Installation And Connection

    SBB-SNOWJAU / SBB-SNOWJMU 6. S-BOX Installation and Connection Samsung Electronics • S-BOX Installation Precautions ① Product recommend installing this product in a standard 19-inch server rack. ※ When connecting two or more times for the purpose of using multi-link HDR, install it on the ground shielded rack and use it.
  • Page 48 S-BOX Installation and Connection Samsung Electronics (Only SBB-SNOWJMU model) • How to install when use Multi Link HDR function  Product recommend installing this product in a standard 19-inch server rack, please refer 38 page about basic installation guide. ① Please open rubber plug of Multi Link HDR port.
  • Page 49 S-BOX Installation and Connection Samsung Electronics (Only SBB-SNOWJMU model) • Multi Link HDR Cable  Use the appropriate cable according to the quantity of S-BOX connected. Multi Link HDR Port Multi Link HDR Port...
  • Page 50 S-BOX Installation and Connection Samsung Electronics (Only SBB-SNOWJMU model) • FPGA Update Guide when using Multi Link HDR Cable ※ Note : Before update, disconnect the Multi Link HDR Cable from S-BOX.  Factory update method  LSM update method Multi Link HDR Port ①...

  • Page 51: S-Box Connection

    6. S-BOX Connection Samsung Electronics ① Input the video signal to the S-BOX. (Input terminal : HDMI, DP) ② Check the signal input from SOURCE STATUS.(RED : HDMI1 , GREEN : HDMI2, Blue : DISPLAY PORT) ③ Connect from the HDBT OUT port of S-BOX to HDBT IN port of Interface Gender using LAN cable.
  • Page 52 6. S-BOX Installation and Connection Samsung Electronics ⑧ Instruction for handling HDBase-T cable ★ Orderly Rolled (Recommend) Random Rolled ★  Do not use “comb” or “pinstripe” cable (Not Recommend)  Use HDBase-T cables with 15 meter long at minimum and 100 meter long at maximum.
  • Page 53 6. S-BOX Installation and Connection Samsung Electronics ⑧ Instruction for handling HDBase-T cable  EMI sources: Keep the cable away from electromagnetic interference environments such as high-voltage electrical cables, electric motors (such as elevators or refrigerators), fluorescent, light-fixtures and so on ...
  • Page 54 6. S-BOX Installation and Connection Samsung Electronics ⑨ Instruction for trimming HDBase-T cable on site.  STP RJ45 shielded Plug. RJ45 Connector should be CAT6 or CAT7 shielded RJ45 and load bar. Load bar  Insert conductors into the plastic loader : Using the standard wiring scheme shown here (T-568B), insert the conductors into the plastic loader piece of the R-J45 connector.
  • Page 55 6. S-BOX Installation and Connection Samsung Electronics ⑩ Instruction for trimming HDBase-T cable on site.  Slide the plastic loader down the cable : Slide the plastic loader down the cable as close to the base as possible.  Cut all conductors Using the wire cutters, cut all conductors leaving approximately 0.5” remaining.
  • Page 56 6. S-BOX Installation and Connection Samsung Electronics ⑩ Instruction for trimming HDBase-T cable on site.  Flip the drain wire up onto the RJ-45 connector Flip the drain wire up onto the RJ-45 connector. Clamp the strain relief down on the purple jacket of the BC-HDKat6a cable using the pair of pliers.
  • Page 57 6. S-BOX Connection (Redundancy) Samsung Electronics ① If Redundant Spec should be used, Connect from DATA IN port of Interface Gender to DATA OUT port of the last cabinet by using OCM Cable. • For HDBT signal stability, use *STP, *FTP CAT6 or higher spec cable designed for HDBT transmission.
  • Page 58 Samsung Electronics ① S-Box Picture Setting according to model • The default picture configurations are optimized for LH015IFH in Samsung factory. • The picture configurations will be configured automatically when you finish the installation. • Fo the best picture quality, Please connect S-Box and LED displays via LSM software properly.
  • Page 59 6. S-BOX Connection (Grouping) Samsung Electronics  S-Box Grouping is a function used to configure a single screen using multi S-Box. If you configure one screen with a single S-Box, do not use this function !! When S-Box Grouping is set up, the quality improvement function(LED HDR) does not work.
  • Page 60 6. S-BOX Connection (Grouping) Samsung Electronics ② Enable S-Box Grouping Home → Video Wall : OFF → On  [Cautions!!] Setup supported resolution for grouping before the grouping function of multi s-box is run by LSM. It can cause the noise of picture or blackout, if resolution is not supported.
  • Page 61 6. S-BOX Connection (Grouping) Samsung Electronics ③ Setup the resolution of input PC  PC: Click the right button of mouse → Click Screen resolution → Click Advanced settings  Click “Monitor” tap → Monitor Settings → Setup “Screen refresh rate” to 60Hz...
  • Page 62 6. S-BOX Connection (Grouping) Samsung Electronics ④ S-box Grouping support resolution...
  • Page 63 6. S-BOX Connection (Grouping) Samsung Electronics ④ Supported resolution for S-box grouping...
  • Page 64 6. S-BOX Connection (Grouping) Samsung Electronics ⑤ Picture menu setting  Both “Dynamic Contrast” and “Black Tone” should be off when using S-Box Grouping, since it may causes a color difference between S-Box.  Menu → Picture → Advanced Settings, - Dynamic Contrast : default “Medium”...
  • Page 65 SBB-SNOWJAU / SBB-SNOWJMU 6. S-BOX Connection (Grouping) Samsung Electronics ⑤ Picture menu setting  When using S-Box grouping, you must set Picture mode to Calibration. Calibration mode deactivates Contrast Enhancer, Black Tone, Auto Motion plus function so that there is no screen difference between S- Box.
  • Page 66 6. S-BOX Connection (Using Service Port) Samsung Electronics  Service Port is used to check full screen, when working of S-box is not abnormal. Refer to the available monitors as below, ■ Available monitors for service port: LH**PMF, LH**PHF, LU28E590DS , LU24E590DS [Cautions!] This port is for servicing only and has no user function.

  • Page 67: Settings And How To Use

    7-1 Control Program for PCs LSM(LED Signage Manager) • LSM Download : Samsung Display Solutions (https://displaysolutions.samsung.com) Samsung Display Solutions > SOLUTIONS > SOFTWARE SOLUTIONS > LED Signage Solution > LED Signage Manager ※ Partner login is necessary for program download...
  • Page 68 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs Network IP Setting by USB Configuration File (※ S-Box(JAU/JMU only) supports since v1050.0) tizen_netconf.toml [network] This is how to set the network information of S-Box with USB device_name = "SNOWBOX“...
  • Page 69 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs Network IP Setting Tool Execute : [Start] – Program – Samsung – LED Signage Manager – Network Configuration Connect PC and Sbox with RS232C Cable, select connected SerialPort(COM*). And click “open” button.
  • Page 70 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Software that adjusts the LED Cabinet Layout in Remote S-box Ethernet PC and S-box should be connected through Ethernet connection. HDBT Control PC...
  • Page 71 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Start– Login Page If the LSM gets operated for the first time, the page to set the password will appear. To set the password, users have to input the same password two times and then click the “Start”...
  • Page 72 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • New Connection To add connection information, you can either use Search function or input the IP address by yourself. If you click on the Search button, the IP addresses available on S-BOX in the same network will appear.
  • Page 73 7. Settings and How to Use Samsung Electronics [★ Cautions!] Recommend to use static IP address for the LED devices. If DHCP is used, IP address is changed automatically and LSM can be 7-1 Control Program for PCs disconnected. The 192.168.10.x band is used for internal communication of the LED Cabinet.
  • Page 74 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs [★ Cautions!] LSM(LED Signage Manager) The network port 1515, 48484, 48485 and 58585 are used for internal communication between S-BOX and LED Cabinet. It should be include the firewall or network exception if customer used secured •...
  • Page 75 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Home Window Input source: Input source, resolution, connection time of S-BOX are shown. Cabinet Layout : Layout, number of units, number of connections and number of disconnections in all LED cabinets are shown.
  • Page 76 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Edit Connection Layout Window Connection layout: The location and the layout of each LED cabinet are adjusted in the output source area of the S-BOX.
  • Page 77 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Connection Window Device connection list view: Check S-BOX composition, modify and delete S-BOX connection, show by each LED Cabinet Group Connection layout (View Port):...
  • Page 78 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Connection Window - Device Information/Setting View 1. Basic : . Power On/Off, Change input source, Screen Mute / Freeze 2. Picture . Change Picture Mode, Brightness / Contrast...
  • Page 79 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Dehumidification Mode using LSM The dehumidification mode icon is provided under the S-Box menu. To turn on dehumidification mode, click the icon. (Proceed : 24 hours) It is possible to view how long the dehumidification has been on.
  • Page 80 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • test pattern using LSM S-Box Test Pattern - Utilize when installing cabinets (only for test) When the test pattern is turned on / off or the pattern is changed, background screen may be visible for a while by overlay layer switching.
  • Page 81 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • System - System Restart Interval (Cont’d) - To stabilize the S-box(SBB-SNOWH3U), execute a reboot automatically at a weekly time. - Default setting : 4:00am, Monday. (Reboot will be executed 4:00am.~5:00am actually.) - Reboot time can be changed by LSM –...
  • Page 82 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • System - System Restart Interval - If you don’t want to be rebooted once a week, you must change the option of factory menu.
  • Page 83 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Connection Window - Device Information/Setting View 6. Cabinet Settings (※ Each menu can be supported for some specific models) . LOD (LED Open Detection) : Check the number of LED Off (Screen can be blinking when Recheck) .
  • Page 84 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Connection Window - Device Information/Setting View 7. Cabinet Calibration . Perform RGB CC calibration for each module/ Cabinet. . Calibrate the boundary surface of each module.
  • Page 85 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Connection Window - Device Information/Setting View . Cabinet Calibration └ Multiple Selection : Calibrate the boundary surface of selected multiple modules. Change offset then brightness is adjusted for edge.
  • Page 86 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Connection Window - Sub Information View Monitor Window: Checking MDC communication log and connected device information available, able to be extracted via file...
  • Page 87 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Main Window-Preference Options number of times the command retried interval of checking error status alarm temperature warnings Support program language Log data management...
  • Page 88 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) • Software Update 1. Prepare the update SW File Info.txt FPGAFW.bin L-IERMWWAC-1001.0 Info.txt 2. Click on the "Software Update" button in "Cabinet Settings" on the LSM menu.
  • Page 89 7. Settings and How to Use Samsung Electronics 7-1 Control Program for PCs LSM(LED Signage Manager) 3. Click the Browse button to select the SW file to update. Info.txt FPGAFW.bin L-IERMWWAC-1001.0 Info.txt ※ Never update the "info.txt" file. Causes system failure.

  • Page 90: Issue And Solution

    8. Issue and Solution Samsung Electronics Problem Case 1 Rule 1: The 1 Cabinet from I/G board must be ID #2 for the LSM Setup Rule 2: The 1 Cabinet from I/G board must be set as Master. The 2 Master cabinet is not allowed for the LSM connection.
  • Page 91 8. Issue and Solution Samsung Electronics Problem Case 2 Rule 1: The 1 Cabinet from I/G board must be ID #2 for the LSM Setup Rule 2: The 1 Cabinet from I/G board must be set as Master. The 2 Master cabinet is not allowed for the LSM connection.
  • Page 92 8. Issue and Solution Samsung Electronics How to do Factory Reset After checking cable connection order, the cabinet which is not display the proper picture position will be Wrong positioned Master cabinet. In this case, Do factory reset to change to slave cabinet .

  • Page 93: Cable Connection

    9. Cable Connection Samsung Electronics 9-1 Cable Connection • If using 110V, you can connect at most three(3) IF015H/IF020H devices. To use IF025H devices with the same voltage, connecting a maximum of four(4) devices is recommended. • If using 220V, you can connect at most four(4) IF015H/IF020H, eight(8) IF025H devices.
  • Page 94 9. Cable Connection Samsung Electronics 9-2. The caution for Cabinet installation and Cable connection(Full Front) 1) The set installation order Must be Left -> Right direction. Because The structure of Wall mount hole for cabinet installation is downward diagonal direction.
  • Page 95 9. Cable Connection Samsung Electronics 9-3 The direction for Cabinet installation 1) Installation of First row cabinet starts at the bottom of Left-end. 2) After installing cabinets one line is complete, make sure the connection is OK by connecting OCM/Power cable. Then, Install next line.
  • Page 96 9. Cable Connection Samsung Electronics Cable Connection : Data flow standard ◎ Connect OCM cable Forward direction Reverse Reverse Forward Forward Reverse Forward Reverse Forward P1.5 FHD P2.0 FHD P2.5 FHD...
  • Page 97 9. Cable Connection Samsung Electronics 9-5 Cable Connection : OCM cable installation standard ◎ Whenever one number of cabinet gets installed, connect necessary cable for each. P1.5 FHD...
  • Page 98 9. Cable Connection Samsung Electronics 9-5 Cable Connection : OCM cable installation standard ◎ Whenever one number of cabinet gets installed, connect necessary cable for each. P2.0 FHD P2.5 FHD...
  • Page 99 9. Cable Connection Samsung Electronics 9-5 Cable Connection : OCM cable installation standard ◎ Whenever one number of cabinet gets installed, connect necessary cable for each. P2.5 FHD...
  • Page 100 9. Cable/Power Connection Samsung Electronics  9-5. Apply COVER CAP to POWER IN CABLE of the top cabinets. POWER-IN CABLE COVER-CAP COVER-CAP 6*3 (Example)

  • Page 101: Seam Adjustment

    10. Seam Adjustment Samsung Electronics • Check and Adjust Seam ① Check whether there is any Black Line between the cabinets in White Screen. (Fig.1) ② Check whether gap, differences occur between each module . (Fig.2) ※ Gap: appears as a black line in every direction.
  • Page 102 10. Seam Adjustment Samsung Electronics • Module Disassembly/Assembly Separate the JIG and module at the same time. Have the Unlock mark head upwards. Place to LED module. Have the Lock mark head upwards. Lock after placing on LED module. Put the replaced module up on the cabinet.
  • Page 103 Samsung Electronics Aluminum profile & Frame Kit Installation Manual Ver. 0.1...
  • Page 104 Contents Samsung Electronics 1. Information and Installation Guide of Aluminum profile 2. Installation of Aluminum profile 3. Installation of Frame Kit...
  • Page 105 • Aluminum profile & Frame Kit composition • Aluminum profile specification Standard 30x60 Al profile Standard 30x30 Al profile LED DISPLAY cabinet Samsung Frame Kit Standard Aluminum profile • Accessories for Aluminum profile assembly • Installation example M6*L10 Screw Standard 30x60 gusset...
  • Page 106 2. Installation of Aluminum profile Samsung Electronics • Bolster Aluminum profile • Aluminum profile installation 1. When Aluminum profile needs enhancement in its strength, add more Aluminum profile as the picture below. 90° 90° 2. All added Al profile material should not block air-vent nor cable connector.
  • Page 107 3. Installation of Frame kit Samsung Electronics • Prepare Frame Kit 1. Disassemble holder screws for the needed area of Frame Kit. ( Relevant Frame : Holders in the side & Holders in the Middle/Center ) * When using Al profile, do not use holder.
  • Page 108 3. Installation of Frame kit Samsung Electronics • Assemble Aluminum profile into Frame Kit 13.9mm ① ② ③ ④ ⑤ ⑥ ⑦ 1. Assemble ASSY BRACKET SIDE starting from the left. (Assembly order : Left→Right) 2. For the locking, use M6 screw and nut to fix it onto Al profile.

This manual is also suitable for:

Lh020ifh as seriesLh015ifh as seriesSbb-snowj3uSbb-snowjmu

Table of Contents