Specification; Specifications - SMC Networks ZSE40A Operation Manual

Specification

■Specifications (Refer to page
Model No.
Rated pressure range
Set pressure range
Withstand pressure
Minimum display unit
Applicable fluid
Power supply voltage
Current consumption
Switch output
Max. load current
Max. applied voltage
Residual voltage
Response time
Short circuit protection
Repeatability
Hysteresis mode
Hys
teresis
Window comparator mode
Output Voltage
Voltage
(rated pressure range)
output
Linearity
2
Output impedance
Analogue
Output current
output
(rated pressure range)
Current
Linearity
output
3
Load impedance
Auto-shift input
Display
Display accuracy
Indicator LED
Enclosure
Operating temp. range
Environ
Operating humidity range
ment
Withstand voltage
Insulation resistance
Temperature characteristics
Lead wire
Standard
1: If the applied pressure fluctuates around the set value, the hysteresis must be set to more than the fluctuation width. Otherwise,
chattering will occur.
2: If analogue voltage output is selected, the analogue current output cannot be selected.
3: If analogue current output is selected, the analogue voltage output cannot be selected.
63 for products with M8 (3 pin) connector)
ZSE40A
(vacuum)
0 to -101.3 kPa
10.0 to -105.0 kPa
500 kPa
0.1 kPa
Air, inert gases and incombustible gases
12 to 24 VDC ±10%, ripple (p-p) 10% or less (protected against reverse
NPN or PNP open collector output, 2 outputs
1 V or less (at 80 mA load current)
(with anti-chatter function: 20, 100, 500, 1000 or 2000 ms)
1 to 5 V ±2.5% F.S.
4 to 20 mA ±2.5% F.S.
Max. load impedance: 300  (at power supply voltage of 12 VDC)
Min. load impedance: 50 
Non-voltage input (reed or solid state), Low level 0.4 V or less,
3 1/2digits, 7-segment, dual-colour display (red/green)
±2% F.S. ±1 digit (at ambient temperature 25±3 C)
LED is ON when output is ON OUT1, OUT2: Orange
Operation: -5 to 50 C, Storage: -10 to 60 C (no condensation or freezing)
Operation, Storage: 35 to 85% RH (no condensation)
1000 VAC, 1 minute between terminals and housing
50 M or more at 500 VDC between terminals and housing
Oil resistant vinyl cabtyre cable
3.5, 2 m
5 cores
Sectional area of conductor: 0.15 mm
Outside diameter of insulator: 0.95 mm
-61-
ZSE40AF
(compound)
-100.0 to 100.0 kPa
-105.0 to 105.0 kPa
500 kPa
0.1 kPa
connection)
45 mA or less
80 mA
28 V (NPN output)
2.5 ms or less
Provided
±0.2%F.S. ±1 digit
1
0 to variable
±1% F.S.
Approx. 1 k
±1%F.S.
600  (at power supply voltage of 24 VDC)
input time 5 ms or more
IP65
±2% F.S. (25 C reference)
CE, UL/CSA, RoHS
ISE40A
(positive pressure)
-0.100 to 1.000 MPa
-0.105 to 1.050 MPa
1.5 MPa
0.001 MPa
0.6 to 5 V
±2.5% F.S.
2.4 to 20 mA
±2.5% F.S.
2
(AWG26)
No.PS※※-OMM0007-H