Table of Contents
Advertisement
6.3 Setting day and time
Setting day and time.
Carry out the following steps to change the day and time
settings:
1. Hold down the P button until the time display starts
flashing.
2. Change the hour with the +or-button and confirm the
change by
pressing the centre button.
The minutes will then begin to flash.
3. Change the minutes with the + or - button and confirm
the change by
pressing the centre button. The number
indicating the day of the week will then begin to flash (1 =
Monday).
4. Change the day with the +or-button and confirm the
change by pressing the centre button.
5. To exit the parameters menu, press P.
6. Wait for 30 seconds while the information is transmitted.
6.4 Checking transmission strength
Carry out the following steps in order to modulate transmission
strength between gas fire and the remote control.
1. Press P until the transmission strength flashes at the top
left of the display.
2. Press the right button until RFCK appears in the display.
3. Walk around the appliance at a distance of 3 to 4 metres
to measure the RFCK. If the RFCK shows a value of 4, the
transmission strength of the remote control is good. If the
value shows as 2 or 3, the RFCK values are acceptable.
Transmission strength is insufficient at a RFCK value of 1.
4. Confirm with
to exit the menu.
6.5 Switching the appliance on and off
Carry out the following steps to turn the appliance on or off:
1. Press
until the >OK< icon in the display appears and
starts to flash.
2. Continue to press
activate the ignition programme.
3. Release both buttons.
The word >WARM< will flash at the top left of the display as
confirmation of activation.
4. Wait a number of seconds until you hear a beep and the
word >WAIT< appears.
The ignition programme will start and the burner will
automatically ignite after approximately 20 seconds.
5. Wait until you hear a second beep.
The word >WAIT< will stop flashing after the ignition
programme.
6. The gas fire flame is alight and operational.
7. Press for approximately two seconds
gas fire flame.
6.6 Setting the flame intensity
The height of the flames can be adjusted from high to low and
is indicated on the display by numbers 1 through 8. The flame
intensity can also be displayed by the flame intensity indicator.
24
and then press briefly on
to extinguish the
The ECO mode has a modulating effect on flame intensity (higher
or lower). This accentuates the visual effect and user comfort
of the flames, while reducing the fire's heat emission and gas
consumption by approximately 40%. Use the remote control to
set the flame intensity in "ECO mode" to 9, after which the double
flame icon
will display on the screen. Adjust the flame intensity
as follows:
1. Press +or -to adjust flame intensity.
2. Release the + or - button.
3. Press the + button until the number 9 appears to switch on
the ECO mode.
6.7 Selecting the thermostat or manual operating
programme
The flame intensity and the resulting room temperature can be
adjusted by setting the remote control in manual or thermostat
mode. To ensure an accurate temperature reading, make sure the
remote control is outside of the fire's radiation range. For security
reasons, the thermostat mode will be automatically switched off
after 24 hours. If the flames in the gas fire have been switched off,
the programme will restart in manual mode automatically when
next switched on.
1. By pressing P until the icon for thermostat
mode
2. Press P again to select the icon of your choice.
3. Briefly press
6.8 Setting the flame intensity by thermostat
The remote control measures the temperature and the flame
intensity is modulated accordingly. To ensure an accurate
temperature reading, make sure the remote control is outside of
the fire's radiation range.
1. Select the thermostat programme as indicated in
paragraph Selecting the thermostat or manual operating
programme on page 24.
2. Press the button with the +or with the -so that the
to
temperature indicator on the display starts to flash.
3. Set the desired temperature with the + and - buttons.
4. Wait for 10 seconds before using the remote control to save
the set temperature.
6.9 Programming time segments
The thermostat function can be combined with a timer
programme that allows for up to three time segments to be
programmed. These are indicated by switch-on times ON 1, 2, 3
and switch-off times OFF 1, 2, 3. The set programme will run daily.
1. Check if the hand transmitter is set at the right time (if you
are not happy with the time, see: 6.3 Day and night settings)
2. Press the P button (hold down briefly).
3. Let go of Button P when the time starts to flash in the top
left-hand corner of the display.
4. Press the right button
comfort). TCOM indicates the maximum temperature
during all set time segments
5. Set the desired temperature with the + or - buttons at
begin to flash.
to exit the menu.
to display "TCOM" (temperature
or manual
Hide quick links:
Advertisement
Chapters
Table of Contents
