Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kalfire Gi105/59F
Summary of Contents for Kalfire Gi105/59F
- Page 1 User Instructions BALANCED FLUE GAS SYSTEMS...
- Page 3 Balanced Flue Gas Systems Kalfire Gi Gi105/59F, Gi110/55C, Gi115/55S Gi105/79F, Gi110/75C, Gi115/75S For gastype: G20, G25, G30 en G31 Version 05-2023_2 Available in French, German and Dutch on request...
-
Page 5: Table Of Contents
Operating Kalfire Gi ....................18 Operation options ........................18 KalSense ring ..........................18 Remote control ........................19 Kalfire Connected app ................... 30 Installing the Kalfire Connected app ................30 Maintenance......................32 Maintenance ..........................32 Door removal..........................34 Replacing batteries ........................ 37 Disassembly and disposal .................... -
Page 6: General Information
General information The following sections provide general information about the gas fire: - Foreword - Pictograms - Warranty - Receipt and verification Foreword This user instruction has been written for the users of the gas fire. A separate Installation Manual accompanies this User Instructions. The user instructions should remain in the vicinity of the gas fire so that they are readily available for fireplace users. -
Page 7: Pictograms
If the gas fire is not installed correctly, all warranty and/or damage claims against Kalfire will be declared null and void. This gas fire has been tested and approved according to CE standard EN-613. Every gas fire that leaves the factory has been tested for technical and functional adherence to relevant quality standards in force. -
Page 8: Warranty
Physical and chemical influences from outside during transport, storage or installation are not covered by the guarantee. The gas fire must be installed by a technician approved by Kalfire according to this Installation Manual and in compliance with all relevant national and regional standards in force. -
Page 9: Gi Fireplace Compatibility
Kalfire and the installer approved by Kalfire. 12. A dated proof of purchase must be presented to Kalfire should a possible home repair service (only available in the Benelux, Germany, France and the United Kingdom) be carried out within the warranty period. - Page 10 (smartphones/tablets), the compatibility of the devices can unfortunately not be checked in advance. Compatibility will only become clear after installation of the interface. Kalfire accepts no liability for the failure of the Gi fireplace to function properly or at all due to causes described here.
-
Page 11: Safety
Safety Safety instructions for decorative elements (filling) FIRE DANGER! The fireplace filling must be placed as prescribed. It is not permitted to change the quantity or configuration of the filling. A change may cause a fire hazard. WARNING! The ignition/ionization pin must remain uncovered, pay attention to this when placing the filling. - Page 12 WARNING! The gas fire must not be started if the front and/or side window is damaged or broken. WARNING! After installation of the gas fire, the visible parts of the appliance (including the glass surface) are considered as part of the active zone. Especially the glass can get extremely hot! Children and dependents are to stay clear of the burning gas fire.
- Page 13 WARNING! Should the floor in front of the fireplace consist of combustible material and the distance from the underside of the combustion chamber to the floor be smaller than 10 cm, a heat-resistant fireguard floor plate larger than 30 cm or a stone should be placed.
-
Page 14: Three Safety Measures For The Gas Fire
The risk of discoloration CAREFUL! After the convection system of the fireplace has been heated, air particles, cigarette smoke, candles and oil lamps can cause discoloration of walls and ceilings. Ensure sufficient ventilation in the room in which the fireplace is installed. CAREFUL! Applying tape to the fireplace is at your own risk, paint damage caused by taping is outside the manufacturer's warranty. -
Page 15: Kalfire Gi Functions
Kalfire Gi functions The Kalfire Gi distinguishes between programmable and manual functions. Manual functions Manual functions are functions with fixed parameters that you cannot adjust yourself. Increase flame height / Decrease flame height The height of the flames can be selected using the Flame Height Up and Flame Height Down function. - Page 16 Thermostat function The thermostat function of the Kalfire Gi can be used to quickly heat the room in which the fireplace is set up. After all, it is not always necessary to heat the entire house or turn on the underfloor heating. Via the app, the desired end temperature can be specified in thermostat mode.
- Page 17 personal moods are programmed via the ConnectedApp, the factory settings apply. Factory settings Moods: Mood 1: Lazy Comfort+: end temperature: 25°C, time: 240 minutes EmberGlow: setting 2 Natural Spark Generator: setting 2 KalSense ring colour: white Mood 2: Comfort Comfort: setting 4 EmberGlow: setting 3...
-
Page 18: Operating Kalfire Gi
Operating Kalfire Gi Operation options Operation of the fireplace can be done using either the Kalfire remote control or the Kalfire Connected app. The Kalfire Connected app offers more and more extensive operating options. This app can be downloaded for free in the Apple and Android app store respectively. -
Page 19: Remote Control
Remote control The remote control buttons are linked to a specific function of the fireplace. The remote control changes the current setting of the fireplace, but does not provide feedback itself. When operated with the remote control, the KalSense ring in the fireplace (centre front) provides feedback. CAUTION! The remote control contains a temperature sensor and should be in the room where the fireplace is set up at all times, at least within 10 meters of the... - Page 20 Bluetooth remote control pairing The remote control should be paired with the fireplace at all times. The remote control is paired with the fireplace at the factory. If the batteries are inserted in the remote control, automatic pairing will take place. You simply check whether the fireplace is paired by operating button 8 (hybrid LED function) on the remote control (see image below).
- Page 21 Then (within 30 seconds), press the key combination below on the remote control to activate the handheld transmitter's synchronisation mode. The red LED light on the top left of the remote control starts flashing. Release the keys. If the green LED light on the communication board is ...
- Page 22 4.3.2. Remote control and symbols Fireplace on/off Comfort+ function Manual control Thermostat function Increase flame height Reduce flame height Comfort functie EmberGlow (hybride functie) Natural Spark Generator...
- Page 23 CAUTION! Change in the flame pattern after selecting a certain function almost always occurs with some delay. Depending on the function selected, this delay may be longer or shorter. The fireplace needs some time to measure the temperature (in some cases), calculate the correct set points and control the three gas valves.
- Page 24 LET OP! You should wait at least 3 minutes after aborting the start-up cycle before restarting the fireplace. If the stove interrupts the start-up cycle for technical reasons or if the stove goes out after completing the start-up cycle, this may have several causes. Check Annex 1 for possible solutions.
- Page 25 KalSense feedback: turquoise From Thermostat function, the following functions (buttons) cannot be activated: Increase flame height (5) Reduce flame height (6) Comfort function (7) The KalSense ring will light up red briefly each time you try to operate one of the functions.
- Page 26 KalSense feedback: Mood1: white Mood2: red Mood 3: blue From the Mood functions, the following functions (buttons) cannot be activated: Increase flame height (5) Reduce flame height (6) Comfort function (7) EmberGlow (8) Natural Spark Generator (option) (9) ...
- Page 27 Manual operation From the programmed modes (Comfort+, thermostat function and Moods) return to manual operation. After activating the Manual function, the KalSense lights up briefly and then goes out again. KalSense feedback: white Increase flame height Increase flame height by briefly pressing the button each time. Positions 1 to 5. Position 1: only middle burner on at low setting, position 2: 3 burners at low setting, position 3, position 4, position 5: 3 burners at high setting.
- Page 28 Reduce flame height Reduce flame height, by briefly pressing the button each time. Position 5 to 1. position 5: 3 burners on high, position 4, position 3, position 2: 3 burners on low, position 1: only middle burner on low. After activating the buttons, the KalSense lights up briefly and then goes out again.
- Page 29 Hybrid-LED function/Ember Glow In run mode (the fireplace is on): each press of the button takes you to the next level in light intensity, with setting 6 being the shuffle/flicker mode. In off mode (the fireplace is off): press the hybrid button and only the hybrid lights will come on, then with each press of the same button you go to the next level.
-
Page 30: Kalfire Connected App
Kalfire Connected app The Kalfire Connected app offers more and more extensive features than the remote control. Besides controlling the various functions, the temperature can be read and programmed for the thermostat and Comfort+ function via this app. Furthermore, 10 Moods can be programmed. - Page 31 (which you can control via the KalfireConnected app). It also allows your dealer to read out technical parameters in case of service or maintenance. If you have completed the one-time registration steps, you can use the KalfireConnected app. 5.1.1 Manual Kalfire Connected App...
-
Page 32: Maintenance
Do not use corrosive or abrasive agents to clean the fireplace. Paint damage is not covered by the guarantee. Minor damage can be touched up with heat-resistant lacquer. Paint is available from your Kalfire dealer. Cleaning the (standard) ceramic windows. - Page 33 6.1.2 Cleaning instructions anti-reflective glass The gas fire glass can become dirty when the fireplace is burning, but also when being taken into use. Potential causes can be: Smoking materials in the fireplace (especially in the beginning), air contamination, quality of the type of gas etc. Anti-reflective glass is polished ceramic glass to which a number of metal oxide coatings have been applied that reduce the reflection to less than 1%.
-
Page 34: Door Removal
Never use the products The glass coating can below: be damaged by : alkaline detergents or toilet cleaners detergents with high levels of ammonia hydrochloric acid acids chlorine or sodium hypochlorite bleach domestos detergents benzene, hexane or solvents petroleum-based solvents scouring powders, abrasive materials, steel wool, scrubbing or scouring pads,... - Page 35 Step 2: Push the metal cover strip in left or right. Step 3: Next, grip the door by the designated handles. Slightly lift the door with glass window out of the rabbet, move the entire door slightly to the left or right (corner fireplace) and carefully lift it entirely out of the fireplace.
- Page 36 6.2.2 Door dismantling and assembly (front models) WARNING Wear (rubber) gloves to prevent stains on the glass. Step 1: Move the metal cover strips up from the upper side. Step 2: To unlock the door, pull the handles that are placed under the hood towards you and up.
-
Page 37: Replacing Batteries
Step 3: Push the metal cover strip in left and right. Step 4: Next, grip the door by the designated handles. Slightly lift the door with glass window out of the rabbet and carefully remove it from the fireplace. Putting the door back in place To put the door back in place, follow the steps described in step 4 in reverse order. -
Page 38: Disassembly And Disposal
Press the back lightly with your thumb and slide the cover upwards at the same time. Replace the battery into the remote control (1 x AAA) Replace the cover in reverse order. Disassembly and disposal Dismantle the device at the end of its service life according to local laws and regulations. -
Page 39: Attachments
Attachments Troubleshooting Start-up phase Problem: The fireplace does not respond to the remote control. Solution: Check whether the remote control is synchronised with the fireplace. This can easily be done by pressing button 8 (hybrid LED function, see section 2.3) on the remote control. - Page 40 Replace the batteries in the remote control. Cause: After going through the start-up cycle, the fireplace automatically goes to the last selected settings: In the case of the thermostat, comfort+ and possibly Moods function, the desired final temperature may have been reached. Possibly the remote control is too close to the fireplace or another heat source.
-
Page 41: Product Card (In Conformance With (Eu) 2015/1186
Product card (in conformance with (EU) 2015/1186 Appendix IV) Model Kalfire Gi105/59F Kalfire Gi105/79F Kalfire Gi110/55C 6,8 kW 81,1% 73,3% Kalfire Gi110/75C Kalfire Gi115/55S Kalfire Gi115/75S Kalfire Gi105/59F Kalfire Gi105/79F Kalfire Gi110/55C 6,9 kW 77,6% 79,7% 68,6% Kalfire Gi110/75C Kalfire Gi115/55S... -
Page 42: Declaration Of Conformity
Product: local gas fire according to the convection principle Type: C11,C31, C91 Product name: Kalfire Kalfire Gi105/59F, Gi110/55C, Gi115/55S, Kalfire Gi105/79F, Gi110/75C, Gi115/75S This declaration of conformity complies with the Harmonisation legislation of the Union:... -
Page 43: Configuration Of The Decorative Elements
Configuration of the decorative elements 7.4.1 Placing the decorative elements Kalfire Gi105/59F, Gi110/55C, Gi115/55S, Gi105/79F, Gi110/75C, Gi115/75S CAREFUL! The decorative elements must be placed according to the instructions. It is prohibited to alter the number of decorative elements or the configuration thereof. - Page 52 Geloërveldweg 21 5951 DH Belfeld info@kalfire.com KALFIRE.COM...