Nakanishi E3000 SELECTOR Operation Manual page 20

(1) Set Motor Selection (Set the Motor Selection Button (MOTOR) ㉓ of the Fig. 22 SELECTOR Control Panel.）
Motor No.1 - No.4 ( ③ , ⑤ , ⑦ , ⑨ ) is selected by pushing the Motor Selection Button (MOTOR) ㉓ . LED ⑳
The corresponding motor selected LED will be illuminated.
(2) Set Motor Rotating Direction (Set the Rotation Direction Button (DIR) ㉒ of the Fig. 22 SELECTOR Control
Panel.）
Check the color of LED ㉔ to verify Motor Direction.
Green : Right hand rotation (FWD.)
Orange : Left hand rotation (REV.)
When changing direction, push the Rotation Direction Button (DIR) ㉒ .
With the cutting tool facing the operator, right hand rotation (FWD.) will be clockwise rotation.
-1
(3) Set 500 min (rpm) Centering Rotation.
(Set the Motor Speed Adjustment Button (SPEED
CAUTION
Never attempt to cut while rotating in Centering Mode.
To select 0.5 (500 min
When controlling motor speed from 1,000 min
(rpm), stop the motor spindle prior to changing speed.
(4) Setting Gear Ratio (Set the Gear Mode Select Button (GEAR) Ⓓ of the Fig. 23 CONTROLLER Control Panel.)
Push the Gear Mode Select Button (GEAR) Ⓓ . (GEAR LED will light.) Check the gear ratio of the spindle or
reducer combination being used. Select the appropriate gear ratio, by pushing the Motor Speed Adjustment
Button (SPEED ,
6.0, 16.
If a GEAR ratio is set other than " 1.0 ", the dot displayed on Digital Speed Indicator Ⓔ will blink.
(Refer to Fig.21.)
If you are not using a speed reducer or an angle type spindle, you do not need to set Gear Ratio Mode.
(Set Gear Ratio to 1.0)
When rotation speed is set 30,000min
and Gear Ratio is set 1.5
When Gear Ratio "1.5 / 2.7 / 4.0 / 6.0 / 16" is set, the
dot displayed on Digital Speed Indicator ⑪ will blink.
(5) Setting Motor Speed (Set the Motor Speed Adjustment Button (SPEED
Control Panel).
Set the speed by pushing the Motor Speed Adjustment Button (SPEED
・ Motor Speed Range is 1,000 - 80,000 min
・ The motor speed is displayed in 1,000 min
・ When using Gear Mode the Digital Speed Indicator ㉕ will show Motor Speed changes at a slower rate than
during operation at ratio 1.0.
* Motor Speed limits depend on the Motor Model. Before using it, refer to the P54 " 6 - 1 Speci¿cations Note : 1 "
section of the E3000 CONTROLLER Operation Manual.
-1
(rpm)), push the Motor Speed Adjustment Button (SPEED
-1
) Ⓑ . Display Speed Indicator Ⓔ , will show the 6 possible gear ratios : 1.0, 1.5, 2.7, 4.0,
-1
(rpm)
⑪
Dot will Blink.
-1
(rpm).
-1
(rpm) increments. 80 equals 80,000 min
) ㉑ of the Fig. 22 SELECTOR Control Panel.）
,
-1
(rpm) to 500 min (rpm) or from 500 min
When rotation speed is set 30,000min
and Gear Ratio is set 1.0
When Gear Ratio is set, the dot displayed
on Digital Speed Indicator ⑪ will turn OFF.
Fig. 21
, ) ㉑ .
-1
(rpm) to 1,000 min
-1
(rpm)
⑪
Dot turns OFF.
) ㉑ of the Fig. 22 SELECTOR
,
, ) ㉑.
-1
(rpm).
-1
47