Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Barco OverView D Series
Summary of Contents for Barco OverView D Series
- Page 1 User's manual OverView D series...
- Page 2 Title: SERIES Date: April 2005 ProdID: doc-3353-2 Revision: This manual is divided into 10 chapters: main update issue chapter 1 chapter 2 chapter 3 chapter 4 chapter 5 chapter 6 chapter 7 chapter 8 chapter 9 chapter 10 new: The corresponding chapters are new or completely revised. corr.: Passages of the corresponding chapter were corrected;...
- Page 3 Copyright © 2002-2005 by Barco Control Rooms All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of the Barco Control Rooms.
- Page 4 Revision sheet • Barco Control Room GmbH Barco Control Room GmbH Barco Control Room GmbH Barco Control Room GmbH An der Rossweid 5, D-76229 Karlsruhe Phone: +49-721-6201-0, Fax: +49-721-6201-298 E-mail: docu.bcd.de@barco.com, Web: www.barcocontrolrooms.de From: Date: Please correct the following points in this documentation:...
-
Page 5: Table Of Contents
3.3 Principle of DMD projection technology ....................3-4 3.4 Principle of dual lamp system........................3-5 3.5 Filter for changing the color temperature (backdrop applications) ............3-7 3.6 Options for the OverView D series: lamps and color temperature filter..........3-8 3.7 Operation elements ............................ 3-9 3.8 Controller..............................3-10 3.8.1 Controller as X.11 Terminal...................... - Page 6 5 Controlling ............................5-1 5.1 Remote control ............................5-2 5.2 Terminology of the RCU controls........................ 5-3 5.3 Projector address ............................5-4 5.3.1 Using the RCU ............................. 5-4 5.3.2 Displaying a projector address ......................5-4 5.3.3 How to program an address into the RCU?..................5-4 5.3.4 Picture controls with direct access.
- Page 7 7.1.6 Indication of the status LEDs......................7-5 7.2 Cleaning the screens........................... 7-6 7.3 Replacement of lamp modules ........................7-7 7.3.1 Behavior on lamp failure ........................7-8 7.3.2 Unpacking a lamp module......................... 7-9 7.3.3 Illumination unit with 2x120W lamps or 2x100W lamps............... 7-10 7.3.4 Illumination unit with 2x200W lamps.....................
- Page 8 9 Trouble shooting ..........................9-1 9.1 LED indication.............................. 9-2 9.2 Hot line................................ 9-3 10 Configuring notes...........................10-1 10.1 Floor space and maintenance area......................10-2 10.2 Overall height ............................10-4 10.3 Viewing distance and angle ........................10-5 10.4 Room ventilation ............................ 10-6...
-
Page 9: Preliminary Remarks
Dual lamp system available as 100W or 120W version This manual describes design, function, operation and maintenance of the large screen rear projection system D of Barco Control Rooms. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 10: The Over View Series
Chapters, pages, figures and tables are numbered separately. Chapters are indicated by a »point syntax«, e. g. 4.2.3, pages by a »dash syntax«, e. g. 2-1. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 11: Styles And Symbols
The sheet icon indicates additional notes. Next to this icon you find further information. This arrow marks tips. Next to this icon you find important notes. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 12: Safety Information
The colors of the mains lead are colored in accordance with the following code: Green-and-yellow: Earth (safety earth) Blue: Neutral Brown: Line (live) ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... - Page 13 Always have service performed on this product by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco replacement parts as they may degrade the safety of this device. Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety tested at the factory and may not be used to power the projector.
-
Page 14: Precautions
Do not attempt to service this device yourself, as opening or removing covers may expose you to dangerous voltage potential and risk of electric shock! Refer all projector service to a qualified Barco service center. Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation. -
Page 15: Abbreviated Summary
2. Abbreviated summary 2 Abbreviated summary This chapter provides a summary of the system components and characteristics. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 16: Design
The burning life of the used lamps is very high. This long lamp lifetime and the low power consumption do not only reduce the cost of ownership but also contribute to saving energy and natural resources. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... - Page 17 The setup of the projection modules can be linear or curved. Figure 2-1 Curved Display Wall consisting of 9x3 OverView cDG67-DL projection modules ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
-
Page 18: Components Of An Overview D Display Wall
Since the screen is illuminated right up to its edges, it is possible to construct Display Walls of any size by the adjacent arrangement of several units. Figure 2-2 Display Wall consisting of 9 OverView mDG50-DL projection modules ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 19: Graphical Control Unit
Ov erv iew D Ov erv iew D Desktop-Serv er SNMP-Manager APOLLO-Base Dev iceCMD SNMP-Agent BarcoRC Figure 2-3 the controller provides the Display Wall with data ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 20: Design And Functions
3. Design and functions 3 Design and functions This section provides a technical description of the equipment listing the fundamental characteristics and func- tional principles. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 21: Projection Module
The projection engines has a dual lamp system and can be operated in three operation modes: Hot Standby, Cold Standby, Auto Switch mode. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... - Page 22 Due to folding up the optical path by a mirror the installation depth of the O D projection unit is ex- ceptionally small. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
-
Page 23: Screen
The example shows a color wheel with three segments red, green, and blue. It is also possible that the segments for the primaries exist twice (RGBRGB), or that a white segment is added (RGBW). ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 24: Principle Of Dual Lamp System
Since there are two lamps, the dual lamp system can have four states: L1 on, L2 on, L1 on, L2 off, L1 off, L2 on, L1 off, L2 off Figure 3-4 Lamp states ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... - Page 25 (When servicing and while standing behind the projection module, the active lamp can also be selected via the manual user interface, cf. Manual user interface). ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
-
Page 26: Filter For Changing The Color Temperature (Backdrop Applications)
However, the light output of the projection systems with a 3200K filter is about only 58% of the light output of 6500K systems: the lamp employed in the OverView D series have a very small share in the red part of the spectral range. -
Page 27: Options For The Overview D Series: Lamps And Color Temperature Filter
3.6 Options for the OverView D series: lamps and color temperature filter For the OverView D series, there are three different illumination unit which employ 2x100W lamp, 2x120W lamp, 2x200W lamp, respectively. All three of them produce "daylight" at a color temperature of 6500K. -
Page 28: Operation Elements
Manual user interface Remote-Control Each OverView D projection module can be controlled by a serial interface or by an IR control unit (IR RCU) ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 29: Controller
Video and RGB Input The controller has inputs to which video cameras or recorders as well as monitor signals can be connected. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 3-10... -
Page 30: Operation
4. Operation 4 Operation This section describes the operation of O ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 31: Cabling
The source to be displayed then is selected vie the OSD, as well as the behavior in case a source fails, cf. Source selection ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 32: Switching-On And -Off Power
Switching the projector to and from standby as well as selecting the active lamp is done via the OSD. When servicing, these actions can also be performed using the manual user interface on the rear of the system, Manual user interface. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 33: Controlling
5. Controlling 5 Controlling ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 34: Remote Control
The remote control is used for control, adaptation and set up. It includes automatic storing of the picture controls (brightness, contrast ...) and the settings. Use the RCU to switch between standby and operational mode. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 35: Terminology Of The Rcu Controls
(This is a visual indicator indication to check the operation of the remote control) ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 36: Projector Address
Press the ADDRESS key (recessed key on the RCU) with a pencil and enter the address with the digit buttons within 5 seconds after pushing the address key. That address can be any digit between 0 and 9. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 37: Picture Controls With Direct Access
Use the + button for a higher contrast. Use the - button for lower contrast. As soon as the optical dimmer is enabled again, these settings get invalid. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 38: Menu Structure
6. Menu structure 6 Menu structure ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 39: General
Lamps Status Brightness Figure 6-1 menu bar Use the cursor key on the RCU to select a menu. Press Enter to activate it. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 40: Operation Menu
The currently selected background is indicated with a white dot. • Use the cursor keys to highlight the desired background • Press Enter to select. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 41: Language
The currently selected status is indicated with a white dot. • Push the cursor key up or down to highlight Disabled, or Enabled • Press ENTER to select. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... - Page 42 English is the only language. The active language is indicated with a white dot. Languages which are not available are grayed out. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
- Page 43 In this operating mode, the behavior is the same as with one DVI-D input only, except that there is the possibility to connect two sources and select alternatively one them without the need of re-cabling. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
- Page 44 The following tables lists all possible cases for connecting source 1 and source 2 as well as the behavior in each of the operation modes: Manual, Auto, Auto Switch. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
- Page 45 = source1 In Auto Switch mode, as soon as the source is switched, priority is also switched! ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
-
Page 46: Lamps Menu
(both lamp are adjusted to have the same brightness). Since both lamps are one, a second subsequent change of the active lamp is immediately possible. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 47: Active Lamp
The lamp activation time can be selected between 12 hours and 500 hours. Therefore when selecting Auto Switch, a dialog pops up to enter the auto switch cycle time: _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-10... -
Page 48: History
Lamp Serial no. Runtime Current lamps Lamp Top Lamp Bottom Figure 6-16 dialog showing the history of the lamps of the projector _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-11... - Page 49 However, when replacing the lamp, it is recommended to select Lamp Optimization, since the new lamp has different parameters and therefore has to be adjusted anew. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-12...
- Page 50 6.5.6 Reset runtime OverView DG Brightness Operation Lamps Status Active Lamp Mode History... Lamp Optimization... Runtimes... Reset runtime Figure 6-21 Reset runtime _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-13...
- Page 51 Use the numeric keys on the RCU to enter the serial number of the new lamp. • Click Accept to activate the serial number. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-14...
-
Page 52: Status Menu
This dialog is also shown during starting up the projector if operation|startup screen is enabled. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-15... -
Page 53: Automatic Startup
6. Menu structure If Long is selected, a list of parameter is shown. This list shows important information for the Barco service tech- nician. Parameter 5998 Figure 6-25 projector identification long: dialog box showing service information 6.6.2 Error OverView DG... - Page 54 OverView D series employs two fans: one which is located behind the filter pad frame and connected to the illu- mination unit and the projection unit, and one which is located beneath the bottom lamp.
- Page 55 This error occurs if the lift did not reach the switches at its upper and lower end position, respectively. Manual reset of this error makes no sense. To solve the problem, call Barco Support! _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-18...
- Page 56 Firmware release 2.0 provides a new algorithm which ensures that there is at least some light on the screen. With Firmware release 1.x the screen remains dark. Switch off the projector and switch it on again. If the error still remains, call Barco Support! Lamp door This error occurs if a lamp door is opened.
- Page 57 No signal available. The projector will go to Standby in 300 sec. Figure 6-31 dialog box warning about the projector switching to standby _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-20...
- Page 58 Use the cursor keys to browse to the input field • Enter the desired value by means of the numeric keys on the RCU. • Press Enter to activate _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-21...
-
Page 59: Brightness Menu
This individual projector adjustment is done after set up of the Display Wall by the Barco Support Technicians. On the screen, the brightness is measured by means of a lux meter, and the sensor of the optical dimmer (DIS) is calibrated based on this measurement. -
Page 60: Brightness Correction (%)
This individual projector adjustment is done after set up of the Display Wall by the Barco Support Technicians. On the screen, the brightness is measured by means of a lux meter, and the sensor of the optical dimmer (DIS) is calibrated based on this measurement. - Page 61 Due to the change in calibration, the brightness is adjusted while the common (all projection modules of the Display Wall) DIS value persists. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 6-24...
-
Page 62: Maintenance And Servicing
Measurements and tests with the opened device may be carried out only in the factory or by specially trained personnel, due to the dangers of electrical shock. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 63: Manual User Interface
[3], the LED’s of the illumination unit, and the LED’s of the lamp doors. The manual user interface is intended to operate the projection module when servicing. The trained Barco sup- port technicians can analyze errors by evaluating the status of the LEDs. -
Page 64: Active Lamp Selection Switch
(error) blinking slowly down no function Projector is start- blinking yellow no function ing up or shutting Down no function down ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 65: Indication Of Power Led
DON’T open the lamp door! (in case the door is opened, an error occurs) Only open the lamp door in case the lamp door LED shines red. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 66: Indication Of The Status Leds
Fans are off (status LED of Fan) Green Static Fans are on blinking slowly Fan error, at least one fan failed service required! ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 67: Cleaning The Screens
Don’t store screens at temperatures exceeding 40ºC (104ºF) ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 68: Replacement Of Lamp Modules
Bevor replacing a lamp module, this lamp has to be inactivated! Only open the lamp door when the lamp door LED shines red! ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 69: Behavior On Lamp Failure
In Cold Standby, after switching the active lamp, the lamp which has been active at that time is only switched off if the second lamp succeeds in being switched on. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 70: Unpacking A Lamp Module
Take hold on the fitting and place the lamp module upside down onto the lower layer. Press the upper layer firmly against it, "opening" on top side, and close the box with adhesive tape! ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 71: Illumination Unit With 2X120W Lamps Or 2X100W Lamps
To open the lamp door, a quarter turn counterclockwise will do • Open the lamp door. Figure 7-3 opening the lamp door _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-10... - Page 72 Fetch the lamp module on its housing. The power socket is on the right side. • Insert the lamp carefully. Take care that the "tubes" slide on the guide rods [2]. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-11...
- Page 73 5 minutes. If the operation mode of the projector has been Hot Standby, the new lamp is immediately switched on. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-12...
-
Page 74: Illumination Unit With 2X200W Lamps
To open the lamp door, a quarter turn counterclockwise will do • Open the lamp door. Figure 7-10 opening the lamp door _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-13... - Page 75 When the lamp is removed, you see the two guiding rods on the upper right/lower left and the additional fan for cooling. Figure 7-14 guiding rods and additional fan, lamp module with plug _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-14...
- Page 76 Reset runtime, Lamp optimization. In emergency cases the lamp optimization procedure can be skipped for the moment and car- ried out later. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-15...
-
Page 77: Disposing Lamp Modules
Note that there may be laws concerning disposal and recycling of burnt-out lamps in your country! Please contact your local authorities to get further information! _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-16... -
Page 78: Replacing The Filter Pad
• Switch on power by pressing ON Never push against a used air filter pad! The trapped dust particles will be released! _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 7-17... -
Page 79: Technical Data
8. Technical data 8 Technical data This chapter provides tabular overviews about the technical details of O D projection modules ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 80: Overview Mdg50-Dl
Weight OverView mDG50-DL projection module 62.5 kg | 138 lbs incl. illumination unit, projection unit, screen Support (1000mm) 30 kg | 66.1 lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 81: Overview Mdr50-Dl
Weight OverView mDR50-DL projection module 65 kg | 143.3 lbs incl. illumination unit, projection unit, screen Support (1200mm) 38 kg | 83.77 lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... - Page 82 Weight OverView mDR+50-DL projection module 62.5 kg | 138 lbs incl. illumination unit, projection unit, screen Support (1000mm) 30 kg | 66.1 lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005...
-
Page 83: Overview Cdg67-Dl
OverView cDG67-DL projection module incl. illumination unit, projection unit, screen 140 kg | 308.64 lbs Support, standard height (1288mm) 60 kg | 132.28 lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 84: Overview Cdr67-Dl
OverView cDR67-DL projection module 140 kg | 308.64 lbs incl. illumination unit, projection unit, screen support, standard height (1288mm) 60 kg | 132.28 lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 85: Overview Cdr+67-Dl
OverView cDR+67-DL projection module incl. illumination unit, projection unit, screen 140 kg | 308.64 lbs Support, standard height (1288mm) 60 kg | 132.28 lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 86: Overview Cdg80-Dl
1117.4mm | 44in. Weight OverView cDG80-DL projection module 128kg | 282.19lbs incl. illumination unit, projection unit, screen support, standard height (1288mm) 60kg | 132.28lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 87: Overview Cdr+80-Dl
1117.4mm | 44in. Weight OverView cDR+80-DL projection module 128kg | 282.19lbs incl. illumination unit, projection unit, screen support, standard height (1288mm) 60kg | 132.28lbs ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 88: Electrical Data Illumination Unit 120 W
8.12 Optical data illumination unit 120 W, projection unit SXGA+ resolution characteristic specification Resolution SXGA+ resolution (1400×1050 pixels) Colors 16.7 millions Brightness uniformity > 95% Brightness 800 lumens (typ.) Contrast 1600:1 ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 89: Electrical Data Illumination Unit 100 W
8.16 Optical data illumination unit 100 W, projection unit SXGA+ resolution characteristic specification Resolution SXGA+ resolution (1400×1050 pixels) Colors 16.7 millions Brightness uniformity > 95% Brightness 650 lumens (typ.) Contrast 1600:1 ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 90: Optical Data Illumination Unit 200 W, Projection Unit Xga Resolution
Up to 80%, non-condensing*) Temperature 0-40°C | 32°F – 105°F*) for OverView cD67 and OverView cD80 temperature range and humidity depending on the overall configuration ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 91: Interfaces
TMDS Data 1+ TMDS Clock Shield TMDS Data 1 Shield TMDS Clock + TMDS Clock - 8.20.2 Remote Control RS232 In RS232 Out ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 92: Scope Of Delivery
R9860705 OverView cD Support Standard, up to 1500mm R9860706 OverView cD Option: Illumination Unit 100W R9842500 Option: Illumination Unit 200W R9842740 (XGA, 240V) ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 93: Consumables
Projection Unit XGA R9841921 Projection Unit SXGA R9841920 Projection Unit SXGA+ R9842670 8.24 Controller For information about the controllers, contact Barco Control Rooms GmbH, please! ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 94: Addresses
Barco N.V. Projection Systems Noordlaan 5 • B-8520 Kuurne • Belgium Phone (32) (56) 36-8211 • Fax (32) (56) 36-8251 E-mail sales.bcd@barco.com • Web www.barcocontrolrooms.com ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 95: Trouble Shooting
9. Trouble shooting 9 Trouble shooting ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 96: Led Indication
9. Trouble shooting 9.1 LED indication In case of a mal function of O D, please check the LED indication first, cf. Manual user interface. ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 97: Hot Line
Feel free to contact us if you have any further questions! • Barco N.V. Projection Systems - Europe Noordlaan 5, B-8520 Kuurne Phone: +32-56-368-211, Fax: +32-56-368-251 E-mail: support.bcd@barco.com, Web: www.barcocontrolrooms.com ________________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005... -
Page 98: Configuring Notes
A number of design and ergonomic conditions must be considered when planning the installation of O In addition to mounting dimensions, the following sections also include anthropotechnical requirements which must be observed in a specific application. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 10-1... -
Page 99: Floor Space And Maintenance Area
An area of at least 15 centimeters must be kept free around each foot. The loading capacity in the area of the feet must be sufficient. Height differences up to ±5 millimeters can be compensated using the adjustable feet. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 10-2... - Page 100 3, 5, and 8 degrees for OverView cD, or 5 and 8 degrees for 50" systems.. Other angles on request! _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 10-3...
-
Page 101: Overall Height
The following picture refers to OverView cDG67-DL. Figure 10-2 Mounting dimensions of O DG67-DL IEW C (All dimensions measured in millimeters!) _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 10-4... -
Page 102: Viewing Distance And Angle
18 angular minutes. This corresponds to a viewing distance less than 200 times the character height. Viewed objects Image on retina Angle of vision Figure 10-4 Angle of vision _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 10-5... -
Page 103: Room Ventilation
D in critical environments like coal- fired power stations etc. please make sure that there are no coal particles suspended in the air. _______________________________________________________________________ Barco - OverView D series - Doc-3353-2 - user's manual - Revision 04 - April 2005 10-6...
Need help?
Do you have a question about the OverView D Series and is the answer not in the manual?
Questions and answers