Reverse Delay; Shuffle Delay; Delay - Roland FA-06 Parameter Manual

IFX Parameters
Parameter Value
D100:0W–
Balance
D0:100W
Level 0–127

50: Reverse Delay

This is a reverse delay that adds a reversed and delayed sound to the
input sound . A tap delay is connected immediately after the reverse

delay .

L in
Feedback
Rev
Rev. Delay
R in
Parameter Value
Threshold 0–127
0–1300 msec,
Rev Delay Time
note
Rev Delay
-98–+98 %
Feedback
Rev Delay HF
200–8000 Hz,
Damp BYPASS
Rev Delay Pan
L64–63R
Rev Delay Level 0–127
0–1300 msec,
Delay 1 - 3 Time
note
Delay 3
-98–+98 %
Feedback
200–8000 Hz,
Delay HF Damp
BYPASS
Delay 1 Pan,
L64–63R
Delay 2 Pan
Delay 1 Level,
0–127
Delay 2 Level
Low Gain -15–+15 dB
High Gain -15–+15 dB
D100:0W–
Balance
D0:100W
Level 0–127
84
Explanation
Volume balance between the direct
sound (D) and the effect sound (W)
Output Level
2-Band
EQ
D1
Delay
D2
D3
2-Band
EQ
Explanation
Volume at which the reverse delay will
begin to be applied
Delay time from when sound is input
into the reverse delay until the delay
sound is heard
Proportion of the delay sound that
is to be returned to the input of the
reverse delay (negative (-) values
invert the phase)
Frequency at which the high-
frequency content of the reverse-
delayed sound will be cut (BYPASS:
no cut)
Panning of the reverse delay sound
Volume of the reverse delay sound
Delay time from when sound is input
into the tap delay until the delay
sound is heard
Proportion of the delay sound that
is to be returned to the input of the
tap delay (negative (-) values invert
the phase)
Frequency at which the hi-frequency
content of the tap delay sound will be
cut (BYPASS: no cut)
Panning of the tap delay sounds
Volume of the tap delay sounds
Gain of the low range
Gain of the high range
Volume balance of the original sound
(D) and delay sound (W)
Output Level

51: Shuffle Delay

Adds a shuffle to the delay sound, giving the sound a bouncy delay
effect with a swing feel .
L in
Feedback
Delay
R in
L out
Parameter
Delay Time
R out
Shuffle Rate
Acceleration
Feedback
HF Damp
Pan A/B
Level A/B
Low Gain
High Gain
Balance
Level
52: 3D Delay
This applies a 3D effect to the delay sound . The delay sound will be
positioned 90 degrees left and 90 degrees right .
L
R
Parameter
Delay Left
Delay Right
Delay Center
Center Feedback -98–+98 %
HF Damp
A
Delay A
B
Delay B
Value Explanation
0–2600 msec, Adjusts the time until the delay sound
note is heard .
Adjusts the ratio (as a percentage) of
the time that elapses before Delay
B sounds relative to the time that
0–100
elapses before the Delay A sounds .
When set to 100, the delay times are
the same .
Adjusts the speed which the Delay
0–15 Time changes from the current setting
to its specified new setting .
Adjusts the amount of the delay that's
-98–+98 % feedback into the effect . Negative (-)
settings invert the phase .
Adjusts the frequency above which
sound fed back to the effect is filtered
200–8000 Hz,
out . If you don't want to filter out any
BYPASS
high frequencies, set this parameter
to BYPASS .
L64–63R Stereo location of Delay A/B
0–127 Volume of delay A/B
-15–+15 dB Gain of the low range
-15–+15 dB Gain of the high range
D100:0W– Volume balance between the direct
D0:100W sound (D) and the effect sound (W)
0–127 Output Level
Level
3D Delay L
3D Delay C
Feedback
3D Delay R
Value Explanation
0–2600 msec, Adjusts the delay time from the direct
note sound until the delay sound is heard .
Adjusts the proportion of the delay
sound that is fed back into the effect .
Negative (-) settings will invert the
phase .
Adjusts the frequency above which
sound fed back to the effect will be
200–8000 Hz,
cut . If you do not want to cut the high
BYPASS
frequencies, set this parameter to
BYPASS .
2-Band
L out
EQ
2-Band
R out
EQ
2-Band
L out
EQ
2-Band
R out
EQ