Step Pitch Shifter; Reverb; Gated Reverb - Roland FA-06 Parameter Manual

IFX Parameters
Parameter Value
High Gain -15–+15 dB
D100:0W–
Balance
D0:100W
Level 0–127

63: Step Pitch Shifter

A pitch shifter in which the amount of pitch shift is varied by a
16-step sequence .
L in
Step Pitch Shifter
Step Pitch Shifter
R in
Parameter Value
Step 01-16 -24–+12 semi
0 .05–10 .0 Hz,
Rate
note
Attack 0–127
Gate Time 0–127
Fine
-100–+100 cent
0–1300 msec,
Delay Time
note
Feedback -98–+98 %
Low Gain -15–+15 dB
High Gain -15–+15 dB
D100:0W–
Balance
D0:100W
Level
0–127

64: Reverb

Adds reverberation to the sound, simulating an acoustic space .
L in
Balance D
Reverb
R in
Balance D
Parameter Value
Type of reverb
ROOM1
ROOM2
Type STAGE1
STAGE2
HALL1
HALL2
Pre Delay 0 .0–100 msec
Time 0–127
88
Explanation
Gain of the high range
Volume balance between the direct
sound (D) and the pitch shifted sound
(W)
Output Level
2-Band
L out
EQ
2-Band
R out
EQ
Explanation
Amount of pitch shift at each step
(semitone units)
Rate at which the 16-step sequence
will cycle
Speed at which the amount of pitch
shift changes between steps
Duration of the pitch shifted sound at
each step
Pitch shift adjustment for all steps
(2-cent units)
Delay time from the original sound
until the pitch-shifted sound is heard
Proportion of the pitch-shifted sound
that is to be returned to the input
(negative (-) values invert the phase)
Gain of the low range
Gain of the high range
Volume balance of the original sound
(D) and pitch-shifted sound (W)
Output Level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Dense reverb with short decay
Sparse reverb with short decay
Reverb with greater late reverberation
Reverb with strong early reflections
Reverb with clear reverberance
Reverb with rich reverberance
Adjusts the delay time from the direct
sound until the reverb sound is heard .
Time length of reverberation
Parameter Value
200–8000 Hz,
HF Damp
BYPASS
Low Gain
-15–+15 dB
High Gain -15–+15 dB
D100:0W–
Balance
D0:100W
Level 0–127

65: Gated Reverb

This is a special type of reverb in which the reverberant sound is cut
off before its natural length .
L in
Balance D
Reverb
R in
Balance D
Parameter Value
Type of reverb
NORMAL
REVERSE
Type
SWEEP1
SWEEP2
Pre Delay
0 .0–100 msec
Gate Time 5–500 msec
Low Gain -15–+15 dB
High Gain
-15–+15 dB
D100:0W–
Balance
D0:100W
Level 0–127
Explanation
Adjusts the frequency above which
the reverberant sound will be cut .
As the frequency is set lower, more
of the high frequencies will be cut,
resulting in a softer and more muted
reverberance . If you do not want
to cut the high frequencies, set this
parameter to BYPASS .
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the reverb sound (W)
Output Level
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Conventional gated reverb
Backwards reverb
The reverberant sound moves from
right to left
The reverberant sound moves from
left to right
Adjusts the delay time from the direct
sound until the reverb sound is heard .
Adjusts the time from when the
reverb is heard until it disappears .
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the reverb sound (W)
Output Level