Table of Contents
Advertisement
35: MULTI TAP DELAY
This effect provides four delays. Each of the Delay Time parameters
can be set to a note length based on the selected tempo. You can also
set the panning and level of each delay sound.
L in
Feed
Delay 1
back
Delay 3
Multi Tap Delay
Delay 4
Delay 2
R in
Parameter
Value
Switch
OFF, ON
Depth Knob
DLY 1 FBACK,
BALANCE
Rate Knob
Delay 1–4
OFF, ON
(sync sw)
Delay 1–4 Time
1–2600 [msec]
(msec)/
Delay 1–4 Time
note (p. 31)
(note)
Delay 1
-98–+98 [%]
Feedback #
200–8000 [Hz],
HF Damp
BYPASS
Delay 1–4 Pan
L64–63R
Delay 1–4 Level
0–127
Low Gain
-15–+15 [dB]
High Gain
-15–+15 [dB]
D100:0W–
Balance #
D0:100W
Level
0–127
Balance D
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Balance D
Explanation
Turns the effect on/off.
Specifies the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Specifies the parameter that is
controlled by the MODULATION FX
[RATE] knob.
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner's manual p. 24).
Adjusts the time until Delays 1–4 are
heard.
Adjusts the amount of the delay
sound that's fed back into the effect.
Negative "-" settings invert the phase.
Adjusts the frequency above which
sound fed back to the effect is filtered
out (BYPASS: no cut).
Stereo location of Delays 1–4
Output level of Delays 1–4
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the effect sound (W)
Output Level
36: REVERSE DELAY
This is a reverse delay that adds a reversed and delayed sound to the
input sound. A tap delay is connected immediately after the reverse
delay.
L in
Feedback
Rev. Delay
R in
Parameter
Value
Switch
OFF, ON
Depth Knob
REV DLY
FEEDBACK,
DLY 3 FEEDBACK,
BALANCE
Rate Knob
Threshold
0–127
Rev Delay Tme
OFF, ON
(sync sw)
Rev Delay Tme
1–1300 [msec]
(msec)/
Rev Delay Tme
note (p. 31)
(note)
Rev Delay
-98–+98 [%]
Feedback #
Rev Delay HF
200–8000 [Hz],
Damp
BYPASS
Rev Delay Pan
L64–63R
Rev Delay Level
0–127
Delay 1–3 Time
OFF, ON
(sync sw)
Delay 1–3 Time
1–1300 [msec]
(msec)/
Delay 1–3 Time
note (p. 31)
(note)
Delay 3
-98–+98 [%]
Feedback #
200–8000 [Hz],
Delay HF Damp
BYPASS
Delay 1 Pan,
L64–63R
Delay 2 Pan
Delay 1 Level,
0–127
Delay 2 Level
Low Gain
-15–+15 [dB]
High Gain
-15–+15 [dB]
D100:0W–
Balance #
D0:100W
Level
0–127
Modulation FX Parameters
2-Band
EQ
Rev
D1
Delay
D2
D3
2-Band
EQ
Explanation
Turns the effect on/off.
Specifies the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Specifies the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Volume at which the reverse delay will
begin to be applied
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner's manual p. 24).
Delay time from when sound is input
into the reverse delay until the delay
sound is heard
Proportion of the delay sound that
is to be returned to the input of the
reverse delay (negative values invert
the phase)
Frequency at which the high-frequen-
cy content of the reverse-delayed
sound will be cut (BYPASS: no cut).
Panning of the reverse delay sound
Volume of the reverse delay sound
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner's manual p. 24).
Delay time from when sound is input
into the tap delay until the delay
sound is heard
Proportion of the delay sound that
is to be returned to the input of the
tap delay (negative values invert the
phase)
Frequency at which the low-frequency
content of the tap delay sound will be
cut (BYPASS: no cut).
Panning of the tap delay sounds
Volume of the tap delay sounds
Gain of the low frequency range
Gain of the high frequency range
Volume balance of the original sound
(D) and delay sound (W)
Output Level
L out
R out
21
Advertisement
Table of Contents
