Table of Contents
Advertisement
Error messages
The bobbin thread is almost empty.
36
The bobbin winder safety device has activated. Is
37
the thread tangled?
The carriage of the embroidery unit will move. Keep
38
your hands etc. away from the carriage.
The safety device was activated since the main
39
shaft motor was heated. Is the thread tangled?
The safety device was activated since the main
40
shaft motor seized. Is the thread tangled?
The safety device was activated since the needle
position sensor malfunctioned.
41
The upper thread may not be threaded correctly.
42
Thread the upper thread from the beginning.
The USB media was changed. Do not change the
43
USB media while it is being read.
There is no needle plate cover. Attach a needle
44
plate cover.
This editing function cannot be used when the
45
pattern is out of the red outline. Use this function
after moving the pattern.
This file cannot be used.
46
This file exceeds the data capacity and cannot be
47
used. Use a suitable size file.
This key cannot be used at this time.
48
This key does not operate when the needle is down.
49
Raise the needle and press the key again.
This stitch is not "Dual Feed Mode" compatible.
50
51
This USB media cannot be used.
This USB media is incompatible.
52
Turn off the machine before attaching or removing
53
the needle plate.
Turn off the power and replace the needle plate.
54
55
USB media error
Cause/solution
This message is displayed when the bobbin thread is running out.
Although a few stitches can be sewn when the "Start/Stop" button is pressed,
replace with a wound bobbin immediately. When embroidering, press
press
, remove the embroidery frame, and then replace the bobbin
with one wound with plenty of embroidery bobbin thread.
If [Upper and Bobbin Thread Sensor] in the general settings screen of the
machine setting mode is set to [OFF], this message does not appear.
This message is displayed when the bobbin is being wound, and the motor
locks because the thread is tangled, etc.
This message is displayed when the embroidery unit is initializing.
This message is displayed when the temperature of the motor increases,
activating the safety device. Wait until the temperature decreases. If the error
persists, contact your nearest authorized Brother dealer.
This message is displayed when the motor locks due to tangled thread or for
other reasons related to thread delivery.
This message is displayed when an error in the needle position sensor is
detected, activating the safety device. Turn the machine off, then on again. If
the message continues to appear, the machine may be damaged. Contact
your nearest authorized Brother dealer.
This message is displayed when it seems that the upper thread has not been
threaded correctly.
This message is displayed when you attempt to select a stitch pattern after
the USB media in which the stitch pattern is saved has been changed.
This message is displayed when the needle plate cover is not attached.
This message is displayed when the machine is in embroidery edit mode,
and you try to use an editing function when the pattern is not completely
within the red outline.
This message appears if the file format is incompatible with this machine.
Check the list of compatible file formats. (page 192)
This message is displayed when the file size exceeds the data capacity of
the machine.
Confirm the file size and format. (page 192)
This message is displayed when you press
other than the Utility Stitch, or press
than the Utility Stitch or Character/Decorative Stitch.
This message is displayed when a key on the LCD display is touched while
the needle is in the down position.
This message appears when the dual feed foot cannot be used with the
current stitch. Select other stitch.
This message is displayed when you try to use incompatible media.
This message is displayed when you try to use incompatible USB media.
For a list of compatible USB media, visit " http://s.brother/cpeaa/ ".
This message is displayed when the regular needle plate is replaced with the
straight stitch needle plate while the machine is ON.
• This message is displayed when the machine is set to embroidery mode or
utility decorative stitch mode from the home page screen while the straight
stitch needle plate or no needle plate is installed.
• This message is displayed when the straight stitch needle plate is installed
while a stitch pattern that cannot be used with that needle plate is
selected.
This message is displayed when an error occurs with the USB media.
ERROR MESSAGES
,
7
in the screen
in the screen other
189
Advertisement
Table of Contents
