Elektro-Automatik PSI 9000 3U Series Operating Manual page 105

TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty .........................................................5
1.3 Limitation of liability ........................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................8
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical Data ...............................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ...................................9
1.8.3 Specific technical data (400 V AC models) .10
1.8.4 Specific technical data (208 V AC models) .20
1.8.5 Views ............................................................28
1.8.6 Control elements ..........................................32
1.9 Construction and function ............................33
1.9.1 General description ......................................33
1.9.2 Block diagram ..............................................33
1.9.3 Scope of delivery .........................................34
1.9.4 Accessories ..................................................34
1.9.5 Options .........................................................34
1.9.6 The control panel (HMI) ...............................35
1.9.7 USB port type B (rear side) .........................38
1.9.8 Interface module slot ...................................38
1.9.9 Analog interface ...........................................38
1.9.10 "Share" connector ........................................39
1.9.11 "Sense" connector (remote sensing) ...........39
1.9.12 Master-Slave bus .........................................39
1.9.13 GPIB port (optional) .....................................39
2
INSTALLATION &
COMMISSIONING
2.1 Transport and storage .................................40
2.1.1 Transport ......................................................40
2.1.2 Packaging ....................................................40
2.1.3 Storage .........................................................40
2.2 Unpacking and visual check ........................40
2.3 Installation ....................................................40
2.3.1 Safety procedures before installation and
use ................................................................40
2.3.2 Preparation ...................................................40
2.3.3 Installing the device .....................................41
2.3.4 Connection to AC supply .............................42
EA Elektro-Automatik GmbH
Helmholtzstr. 31-37 • 41747 Viersen
Germany
2.3.5
2.3.6
2.3.7
2.3.8
2.3.9
2.3.10 Connecting the "Share" bus ........................48
2.3.11
2.3.12 Initial commission .........................................48
2.3.13 Commission after a firmware update or a
2.3.14 System extension with slave units ..............49
3
OPERATION AND APPLICATION
3.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
3.4.9
3.4.10 Recording to USB stick (logging) ................65
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.6
3.6.1
3.6.2
3.7
3.8
3.9
3.10
3.10.1 Introduction...................................................75
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
PSI 9000 3U Series
Connection to DC loads ...............................45
Grounding of the DC output ........................46
Connecting the analog interface .................46
Connection of remote sense .......................46
Installation of an interface module ...............47
Connecting the USB port (rear side) ...........48
long period of non-use .................................48
Personal safety ............................................50
Operating modes .........................................50
Voltage regulation / Constant voltage .........50
Current regulation / constant current / current
limiting ..........................................................51
Power regulation / constant power / power
limiting ..........................................................51
Internal resistance regulation ......................51
Alarm conditions ..........................................52
Power Fail ...................................................52
Overtemperature ..........................................52
Overvoltage protection.................................52
Overcurrent protection .................................52
Overpower protection ..................................52
Manual operation .........................................53
Switching on the device ...............................53
Switching off the device ...............................53
Configuration via MENU ..............................53
Adjustment limits ..........................................62
Changing the operating mode .....................62
Manual adjustment of set values .................63
Switching the main screen view ..................63
The meter bars .............................................64
Switching the DC output on or off ...............64
Remote control .............................................66
General .........................................................66
Control locations ..........................................66
Remote control via a digital interface ..........66
Remote control via the analog interface
(AI) ................................................................67
Alarms and monitoring .................................71
Definition of terms ........................................71
Device alarm and event handling ................71
Control panel (HMI) lock ..............................73
Limits lock .....................................................73
Loading and saving a user profile ...............74
The function generator.................................75
www.elektroautomatik.de
ea1974@elektroautomatik.de
Page 3