Table of Contents Safety ........................4 Key to symbols ....................4 GLP Service and Support ................. 5 Avoiding damage to the fixture ..............5 Powering the fixture off ..................5 Features ........................6 Intended use ...................... 6 Lamp ........................6 Control options ....................
GLP® supplier, who will be happy to help. The user documentation for GLP Highlander Wash lighting fixtures consists of: ● The Highlander Wash Quick Start and Safety Manual, supplied with Highlander Wash fixtures and available for download from www.glp.de. The Quick Start and Safety Manual contains important safety information and installation instructions that the installer and user must read.
You can toggle between these two settings under Lamp Power in the Fixture Settings control menu. See the Highlander Wash Quick Start and Safety Manual for details of the lamp power available when the fixture is connected to AC mains power below 200 V.
® Pan and tilt The Highlander Wash pans through 640° and tilts through 262° with coarse and fine control channels and self-correcting position feedback. Position feedback can be disabled and control of pan and tilt can be reversed using the control panel or via DMX on the Special/Control channel.
Color wheels See Figure 2. The Highlander Wash features two separate color wheels with dichroic color filters: ● Color wheel 1 offers seven saturated colors plus open. ● Color wheel 2 offers four pastel colors, half minus green and two color correction filters plus open.
Zoom The Highlander Wash has a 1:7 zoom range. You can vary the beam angle from 5° to 44° (half-peak) / vary the field angle from 11° to 63° (one-tenth peak). Control on the Zoom DMX channel is normally from spot to flood as the DMX value increases.
● In Smooth mode, movement is set to optimize smoothness and give lowest-noise performance. This setting gives extremely low noise and smooth performance but effect movement will be slower than in Normal mode. You can select Movement Performance using either the control panel or the Special/Control DMX channel. Highlander Wash User Manual...
Offsets You can customize the Highlander Wash by creating offsets in the fixture’s effects, including pan and tilt. Custom offsets let you adjust fixtures in multiple installations to compensate for the different positions of the fixtures in the rig, for example.
When you unlock the display you will see this screen: V:26/NS Shortcut Menu Figure 3. Control panel See Figure 3. From left to right, the top line of the default screen displays: ● Main CPU software version Highlander Wash User Manual...
If the display orientation is set to Auto, pressing both keys inverts the display temporarily regardless of its current orientation. After you exit the menus, or after a short period with no key presses, the display will return to its Auto orientation. Highlander Wash User Manual...
German Light Products ® Control menus Quick menu The control panel’s Quick Menu gives you quick access to the most frequently used commands. You can open the Quick Menu when you press the left-hand control button (marked Shortcut) when the display is showing the default screen. The Quick Menu contains the following items: Menus Notes...
Main menu The following menus and commands are available in the Highlander Wash control panel. Menus Notes DMX Start Address 1-490 Set fixture’s DMX address Protocol Setup Control via DMX protocol Select Control via Art-Net Control Art-Net protocol (default)
Page 17
German Light Products ® Soft (square law) dimming Soft (Square) Dimmer curve Curve Linear Linear dimming curve Display dims after a short period of inactivity if no Auto errors and valid DMX signal Display Mode Display constantly on Display dims even if there are errors / no DMX signal Display automatically Auto...
Page 18
Shows AC power voltage Main AC information Manual Control Lamp On/Off Power lamp on/off Reset All Reset all effects Reset Pan & Reset pan and tilt Tilt Reset all effects except Reset Head pan and tilt Highlander Wash User Manual...
Page 19
Factory Backup (!) Yes/No Ethernet / CRMX configuration, user offsets and user presets) – hold for 5 secs. Contact GLP Service before entering this menu – changes can cause Enter Factory Mode Yes/No damage to the fixture that is not covered by the...
Page 22
84.7 – 96.1% Reset pan/tilt only * 246 – 248 96.5 – 97.3% Reset head only* 249 – 251 97.6 – 98.4% Reset all* 252 – 255 98.8 – 100% * Hold value for 3 seconds to apply Highlander Wash User Manual...
Page 23
German Light Products ® Notes Default settings are written in bold type. To apply a command on the Special/Control channel, send the corresponding DMX value for 3 seconds. Percentage values are calculated by dividing DMX values by 2.56 and rounding to the nearest 0.1%.
Status and error codes This section provides a key to the five-letter status and error codes used in the Highlander Wash. All states except HOT are sticky, meaning they are shown in the fixture’s control panel display until the next power cycle or the next motor reset.