Danfoss VLT AutomationDrive FC 302 Instruction Manual page 66

Specifications
Type designation
High/normal load*
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure protection rating IP21
Enclosure protection rating IP54
Enclosure protection rating IP20
Output current
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [kVA]
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 550 V) [A]
8 8
Continuous (at 575 V) [A]
Continuous (at 690 V)
Additional specifications
Maximum cable size: Line power, motor, brake and load
share mm (AWG)
Maximum external electrical fuses [A]
Estimated power loss at 575 V [W]
Estimated power loss at 690 V [W]
Weight, enclosure protection rating IP21, IP54 kg (lbs.)
Weight, enclosure protection rating IP20 kg (lbs.)
Efficiency 2)
Output frequency
Heatsink overtemperature trip
Control card ambient trip
*High overload=150% current for 60 s, Normal overload=110% current for 60 s.
Table 8.3 Line Power Supply 3x525–690 V AC
1) Applies for dimensioning of adjustable frequency drive cooling. If the switching frequency is higher than the default setting, power loss may
increase. LCP and typical control card power consumption is included. For power loss data according to EN 50598-2, refer to www.danfoss.com/
vltenergyefficiency.
2) Efficiency measured at nominal current. For energy efficiency class, see chapter 8.4 Ambient Conditions. For part load losses, refer to
www.danfoss.com/vltenergyefficiency.
The typical power loss is at nominal load conditions and expected to be within ±15% (tolerance relates to variety
in voltage and cable conditions).
The losses are based on the default switching frequency. The losses increase significantly at higher switching
frequencies.
The options cabinet adds weight to the adjustable frequency drive. The maximum weights of the D5h–D8h frames
are shown in Table 8.4.
64
®
VLT AutomationDrive FC 302
HO
160
250
200
253
380
242
363
241
241
289
245
234
240
3012
1)
3121
1)
Danfoss A/S © 06/2015 All rights reserved.
N200 N250
NO HO
200 200
300 300
250 250
D2h D2h
D2h D2h
D4h D4h
303 303
333 455
290 290
319 435
289 289
289 289
347 347
299 299
286 286
296 296
2x185 (2x350)
550
3723 3642
3848 3768
125 (275)
125 (275)
0.98
0–590 Hz
110 °C (230 °F)
75 °C (167 °F)
N315
NO HO NO
250 250 315
350 350 400
315 315 400
D2h
D2h
D4h
360 360 418
396 540 460
344 344 400
378 516 440
343 343 398
343 343 398
411 411 478
355 355 408
339 339 390
352 352 400
4465 4146 5028
4610 4254 5150
MG34U422