Table of Contents
Advertisement
eBUS
Button Panel EU and MK Series • Setup Guide (Continued)
®
Prior to mounting:
If it has not already been done, feed all device cables through the wall or furniture.
1.
Ensure that cables are connected to the EBP rear panel (see
2.
NOTE: The EBP VC1 EU and EBP VC1 MK are deeper than other EU or MK panels and have front panel rotary encoders that
protrude from the wall more than the buttons of the other models.
•
Allow at least 1.44 inches (36.6 mm) depth in the wall or furniture for cables.
•
The EBP VC1 EU or EBP VC1 MK front panel, including the rotary encoder, extends 0.77 inches (19.6 mm) from the
wall.
Mounting EBP EU or EBP MK Devices to an
Electrical Wall Box
The EBP EU models can be mounted into one-gang EU junction
boxes and enclosures having 60 mm mounting centers. Figure 14
shows how to mount the EBP 106 EU. Other 1-gang EU models are
mounted in exactly the same way. The EBP EU models can also be
mounted directly into an EU raceway (see
in a Raceway
on the following page).
The EBP MK models can be mounted in any standard 1-gang
MK electrical junction box. Figure 15 shows how to mount the
EBP 106 MK. Other 1-gang MK models are mounted in exactly the
same way.
NOTES:
•
The electrical wall box is not provided and must be
purchased separately.
•
Install the electrical wall box by following the instructions
provided by the manufacturer.
•
Use the metal bracket provided with EBP device.
Mount the EBP device as follows:
Decide where the panel will be located. Take into consideration
1.
the position of wall studs and windows that could obstruct cable
runs.
Install the electrical wall box (
2.
provided by the manufacturer.
Attach the provided mounting bracket (
3.
provided screws.
NOTES:
•
The mounting brackets provided with the EU and MK
models are different and are not interchangeable.
•
Ensure the bracket is in the correct orientation (with
the side marked "Front" facing away from the wall.
•
The EU model is attached with screws at the top and
bottom.
•
The MK model is attached with screws on both the
sides.
Disconnect power from all devices at the source and run cables
4.
through the hole in the wall. Pass them through the metal bracket
and frame and connect them to the rear panel captive screw
connectors (see
Step 5: Cable All Devices
Set the DIP switches to give the panel a unique eBUS ID (See
5.
Step 4: Set the eBUS ID on page
Insert the EBP into the frame (
6.
into the metal bracket (
bracket by two catches (one on each side) and holds the frame in
place.
NOTE: The EBP 104 EU and EBP 104 MK are held in place by
four catches, two on the top and two on the bottom.
12
Mounting EBP EU Devices
1
) by following the instructions
2
) using the two
on page 9).
6).
3
) and press the entire assembly
2
). The EBP is secured to the metal
EBP Rear Panel Features
on page 1).
Wall Box
1 1
2 2
Mounting Bracket
Mounting with an EU Wall Box
Figure 14.
1 1
Mounting Bracket
Mounting with an MK Wall Box
Figure 15.
3 3
S P
D I
O N
L U
V O
Frame
P C
EBP 106 EU
Wall
MK Wall Box
2 2
3 3
D I
O N
V O
Frame
P C
P T
L A
EBP 106 MK
Y
L A
F
O F
M E
Y
L A
S P
F
O F
M E
L U
E O
V ID
P C
T E
M U
E O
V ID
O P
Advertisement
Table of Contents
