Table of Contents
Advertisement
Planning the System and Installation
When planning to install an eBUS system, consider how many EBP button panels to use, maximum cable distance, cabling
topology, and mounting. See the eBUS Technology Reference Guide for more information about eBUS topologies.
Installation
Step 1: Get Ready
Use the following check list to prepare for the installation.
Download and install the latest version of the software, firmware, and device drivers needed to configure or program the
†
IPCP Pro and control the connected AV products. See the IPCP Pro Series User Guide (available at www.extron.com)
for details on software and drivers.
Obtain model names, drivers, and setup information for AV devices.
†
Determine which eBUS cabling topologies to use and obtain cables, mounting hardware, and any power supplies or
†
hubs required by that configuration.
Step 2: Prepare the Installation Site
ATTENTION:
•
Installation and service must be performed by authorized personnel only.
•
L'installation et l'entretien doivent être effectués par le personnel autorisé uniquement.
•
If the EBP will be installed into fine furniture, it is best to hire a licensed, bonded craftsperson to cut the access hole
and perform the physical installation so the surface will not be damaged.
•
S'il est prévu d'installer le EBP dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et qualifié
pour couper le trou d'accès et réaliser l'installation de telle façon que la surface ne soit pas endommagée.
•
Follow all national and local building and electrical codes that apply to the installation site.
•
Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s'appliquent au site de l'installation.
Site preparation
The EBP EU panels fit any one-gang EU junction boxes, enclosures having 60 mm mounting centers, or Flex55 enclosures. The
EBP MK panels fit any standard MK junction box. In addition, Extron offers an assortment of optional in-wall junction boxes,
external wall boxes (EWBs), and surface or tabletop mounting boxes for use with the eBUS button panels (see www.extron.com).
NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the EBP must be
installed in a UL Listed junction box (not included with the EBP). The end user or installer must furnish the junction box.
Americans with Disabilities Act (ADA) compliance
When planning where to install these devices, you may need to consider factors affecting accessibility of the button panel such
as height from the floor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see
sections 307 ("Protruding Objects") and 308 ("Reach Ranges") of the 2010 ADA Standards for Accessible Design available at
http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.
Step 3: Change the Buttons
You can replace a faceplate or one or more of the individual buttons. You can order replacement or custom buttons using the
Custom Button Builder at www.extron.com. To replace the buttons:
If required, remove the rotary encoder knob (EBP VC1 EU or EBP VC1 MK only) (see
1.
(VC1 models only)
Remove the button panel. For most models, see
2.
following page. The procedure is slightly different for the EBP 104 EU and EBP 104 MK (see
104 EU or EBP 104 MK
Separate the button panel from the control panel. This step uses the same procedure for all models (see
3.
from the button board (all models)
Replace the buttons. For all models except the EBP 104 EU or EBP 104 MK, see
4.
EBP 104 EU and EBP 104 MK) on page
EBP 104 EU and EBP 104 MK
on the next page).
on the following page).
on page 5)
5. For the EBP 104 EU and EBP 104 MK, see
on page 5.
Remove the bezel (except the EBP 104 EU and EBP 104 MK)
Product Category
Remove the rotary encoder knob
Remove the bezel on the EBP
Separate the bezel
Replace buttons for all models (except
Replace buttons for the
on the
3
Advertisement
Table of Contents
