Emerson Micro Motion 2700 Configuration And Use Manual page 170

Model 2700 PROFIBUS Block Parameters
Table F-5 Transducer block 1 parameters (continued)
Index Parameter Mnemonic
149 UNI_Alarm_Index
(DD Name: Alarm N Index)
150 SYS_AlarmSeverity
(DD Name :Alarm Severity)
151 SYS_AlarmStatus
(DD Name :Alarm Status)
152 SYS_AlarmCount
(DD Name : Alarm N Count)
153 SYS_AlarmPosted(DD Name :
Alarm N Last Posted)
154 SYS_AlarmCleared
(DD Name : Alarm N Last
Cleared)
155 SYS_AckAlarm
(DD Name : Acknowledge)
156 SYS_AckAllAlarms
(DD Name : Acknowlege All)
157 SYS_ClearAlarmHistory
(DD Name: Reset Alarm
History)
158 EMPTY
159 EMPTY
162
Definition
Alarm Index
Alarm Severity
Alarmn Status (write 0 to
acknowledge alarm)
bit #0 = active (0=no, 1=yes)
bit #1 = unacknowledged (0=no,
1=yes)
Alarm n count(inactive to active
transition)
Alarmn Last Posted (seconds
since January 1, 1996)
Alarmn Last clearded (seconds
since January 1, 1996)
Acknowledge alarm (write alarm
index to acknowledge the alarm)
1=A1,..., 39=A39, 40=A100, ...,
70=A130)
Acknowledge All Alarms
Reset Alarm History ("On" =
reset, "Off" = N/A)
Message Data Type/ Size
Type Structure
ENUM Unsigned8 1
ENUM Unsigned8 1
Unsigned8 BIT_ENUM 1
ERATED
VARIABLE Unsigned16 2
VARIABLE 4
Unsigned32
VARIABLE 4
Unsigned32
VARIABLE Unsigned16 2
Method Unsigned8 1
Method Unsigned8 1
Store Default Access Enumerated List of
/Rate Value Values / Range
(HZ)
S 0 R/W 0 = Reserved
1 = NVM Failure
2 = RAM error /ROM
error
3 = Sensor Fail
4 = Temp. Overrange
5 = Input Overrange
6 = Transmitter not
charactized
7 = Reserved
8 = Dens. Overrange
9 = Xmitter Init
10= Cal Failed
11= Cal Fail: Low
12= Cal Fail: High
13= Cal Fail: Noisy
14= Transmitter Fail
15= Reserved
16= Line RTD Over
Range
17= Meter RTD Over
Range
18= Reserved
19= Reserved
20= Uncofig – K1
21 = Unrecognized /
Unentered sensor
type
22 = NV Err (CP)
23= NV Err (CP)
24= NV Err (CP)
25= Boot Fail (CP)
26= Reserved
27= Security Breach
28= Reserved
29= Internal
Communication
Failure
30= Hardware /
Software
Incompatible
31 = Low power
32 = Meter
Verification Fault
Alarm
33 = Tube not full
34-41 = Undefined
42= Drive Overrange
43 = Data Loss
Possible
44= Cal in Progress
45= Slug Flow
46= Undefined
47= Power Reset
48-55= Reserved
56= API: Temp OOL
57= API:Density OOL
58-59= Reserved
60= CM: Unable to fit
curve data
61= CM:
Extrapolation alarm
62-70= Reserved
71 = Meter
Verification Info
Alarm
72 = Simulation
Mode.
73- 139 = Undefined
S 0 R/W 0 = Ignore
1 = Info
2 = Fault
D/20 -- R/W Between 0 to 3
S --- R N/A
S --- R N/A
S ---- R N/A
S ---- R/W Enum list is same as
Alarm Index – R1237
S ----- R/W 0x00 = Not used
0x01 = Acknowledge
S ---- R/W 0x00 = Not used
0x01 = Reset
Model 2700 Transmitter with PROFIBUS-PA
Modbus
Register /
Coil
R-1237
R-1238
R-1239
R-1240
R1241-1242
R1243-1244
R-2623
Coil-0241
Coil-0053