Kit Selection - Kohler APM802 Installation Instructions Manual

Controller
APM802 GM91356-KP1,
GM91356-S1
DEC 3+ GM91356-S4
DEC 3+
(with GM32644-KP1
Comm. Module)
DEC 550
GM91356-KP1,
DEC 3000
GM91356-S1
DEC 3500
DEC 6000
DEC 8000
KPC 1000 GM91356-S7
MPACr 750
MPACr 1000
MPACr 1200
MPACr 1500
Any non NFPA110 GM62466-KP1
Figure 4 RSA III Kit Selection
A PC with SiteTecht software is required to make
the RSA III functional. Use your SecurID to access
KOHLERnet, click on the TechTools button, and follow
the instructions to download the files. See SiteTecht
Software Settings and refer to TP-6701 SiteTecht
Software Operation Manual for more information.
The RSA III kits include components for surface
mounting or flush mounting.
RSA III annunciators used with DEC 3+ controllers
require a separate communication module that can be
provided with RSA III kit selection (Figure 4).
If a fault occurs, the RSA III horn activates and the
corresponding LED illuminates. The following paragraphs
describe specific features of the RSA III.
If the RSA III is used with an Ethernet communication
network, order Modbusr
GM41143-KP2 and refer to TT-1405 Converters,
Connections, and Controller Setup for Network
Communication for system installation.
If the RSA III is used with a DEC 3+ controller, it will
require a communication module board; refer to
TT-1285 Program Loader Software instructions for
downloading firmware version 1.23 and higher.
The RSA III is compatible with the following controllers:
APM802 (compatible with RSA firmware version
D
2.0.8 or higher)
Modbusr is a registered trademark of Schneider Electric.
2
RSA III
RSA III with single ATS
GM91356-KP2,
GM91356-S2
GM91356-S5
GM91356-KP2,
GM91356-S2
GM91356-S8
—
GM91356-KP2,
GM91356-S2
—
GM91356-S5
—
GM91356-S8
—
GM62466-KP1
Ethernet converter
RSA III
with multiple ATS
GM91356-KP3,
Includes RSA III only
GM91356-S3
Includes RSA III and communication module,
GM91356-S6
GM32644-KP1 Comm. Module Kit (loose)
GM91356-KP3,
Includes RSA III only
GM91356-S3
GM91356-S9 Includes RSA III and KPC 1000 harness
GM91356-KP3,
GM91356-S3
See above for controller requirements to
GM91356-S6 determine which kit to use
GM91356-S9
GM62466-KP1 Optional RSA power supply kit
DEC 3+ controller with GM28725 (red) circuit board,
D
firmware version 1.13 and higher with the GM47242
communication module board.
communication module board requires controller
firmware version 1.23 and higher.
DEC 3+ controller with GM64497 (blue) circuit board,
D
firmware version
communication module boards.
DEC 550 controller firmware version 2.10 and higher.
D
DEC 3000 controller firmware version 1.0 and higher.
D
DEC 3500 controller firmware version 1.0 and higher.
D
DEC 6000 controller firmware version 2.5 and higher.
D
DEC 8000 (compatible with RSA firmware version
D
2.0.8 or higher)
KPC 1000 controller firmware version 1.41 and
D
higher.
MPACr750 version 1.00 and higher.*
D
MPACr1000 version 2.03 and higher.*
D
MPACr1200 version 1.00 and higher.*
D
MPACr1500 version 1.15 and higher.*
D
* RSA III with ATS controls only.
Note: Should any communication issues occur when
adding RSA III slaves and/or transfer switches to
the system, be sure to power down the RSA III
master and then power up the RSA III master so
that the RSA III master can recognize the
changes.
The GM49791-1
2.03 and higher with
TT-1625 7/17
all