Yaesu FTDX101D Operation Manual page 86

RADIO SETTING
- MODE SSB -
AGC FAST DELAY
Function: Sets the AGC-FAST DELAY voltage
decay characteristics for SSB mode.
Available Values: 20 - 4000msec
Default Setting: 300msec
Description: Sets the AGC voltage decay char-
acteristics in 20 msec steps after
the input signal level becomes lower
than the AGC detection level and the
HOLD time has expired.
AGC MID DELAY
Function: Sets the AGC-MID DELAY voltage de-
cay characteristics for SSB mode.
Available Values: 20 - 4000msec
Default Setting: 1000msec
Description: Sets the AGC voltage decay char-
acteristics in 20 msec steps after
the input signal level becomes lower
than the AGC detection level and the
HOLD time has expired.
AGC SLOW DELAY
Function: Sets the AGC-SLOW DELAY voltage
decay characteristics for SSB mode.
Available Values: 20 - 4000msec
Default Setting: 3000msec
Description: Sets the AGC voltage decay char-
acteristics in 20 msec steps after
the input signal level becomes lower
than the AGC detection level and the
HOLD time has expired.
LCUT FREQ
Function: Sets the low-frequency cutoff audio fil-
ter in SSB mode.
Available Values: OFF / 100Hz - 1000Hz
Default Setting: 100Hz
Description: The cutoff frequency can be set at
50 Hz increments between 100 Hz
and 1000 Hz.
LCUT SLOPE
Function: Sets the slope of the low-frequency
cutoff audio filter in SSB mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 6dB/oct
HCUT FREQ
Function: Sets the high-frequency cutoff audio
filter in SSB mode.
Available Values: 700Hz - 4000Hz / OFF
Default Setting: 3000Hz
Description: The cutoff frequency can be set at
50 Hz increments between 700 Hz
and 4000 Hz.
84
HCUT SLOPE
Function: Sets the slope of the high-frequency
cutoff audio filter in SSB mode.
Available Values: 6dB/oct / 18dB/oct
Default Setting: 6dB/oct
SSB OUT SELECT
Function: SSB signal output band setting from
RTTY/DATA jack.
Available Values: MAIN / SUB
Default Setting: MAIN
Description: Select the band to output the SSB
signal.
SSB OUT LEVEL
Function: Sets the level of the receive SSB signal
output from the RTTY/DATA jack.
Available Values: 0 - 100
Default Setting: 50
TX BPF SEL
Function: Selects the audio passband of the DSP
modulator on the SSB mode.
Available Values: 50-3050 / 100-2900 / 200-2800/
300-2700 / 400-2600 (Hz)
Default Setting: 300-2700 Hz
SSB MOD SOURCE
Function: Selects the microphone input jack for
SSB mode.
Available Values: MIC / REAR
Default Setting: MIC
Description:
MIC: Audio is input from the MIC jack on the
front panel.
REAR: Disables the microphone circuit on the
front panel and inputs audio/data from the
USB jack or RTTY/DATA jack on the rear
panel.
REAR SELECT
Function: Selects the input jack of the SSB sig-
nal.
Available Values: DATA / USB
Default Setting: DATA
Description: Selects the input jack of the SSB
signal when "SSB MOD SOURCE"
is set to "REAR".
DATA: Inputs from the RTTY/DATA jack on the
rear panel.
USB: Inputs from the USB jack on the rear pan-
el.
RPORT GAIN
Function: Sets the level of the SSB signal input
when "SSB MOD SOURCE" is set to
"REAR".
Available Values: 0 - 100
Default Setting: 50