Yaesu FTDX101D Service Manual
Hide thumbs
Also See for FTDX101D:
- Operation manual (122 pages) ,
- Quick start manual (3 pages) ,
- Technical supplement (195 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for Yaesu FTDX101D
Summary of Contents for Yaesu FTDX101D
- Page 1 1. Remove 16 screws and open the bottom case.
- Page 2 Ｊ02 Ｊ03 When installing the filters (XF-128CN/ XF-128S) on the marking：none marking： MAIN side（RX-1-UNIT) Green 2.Remove 9 cables connected with the RX-1-UNIT. Coaxial ：7 place Ｊ01 FFC cable：2 place marking：Red Ｊ09 marking： Black MAIN RX-1-UNIT RX-2-UNIT MAIN RX-1-UNIT Ｊ11 marking： none Ｊ12 marking：...
- Page 3 When installing the filters (XF-128CN/ XF-128SN) on the MAIN side（RX-1-UNIT) 3. Remove 6 Screws and remove the RX-1-UNIT from the chassis. MAIN RX-1-UNIT RX-2-UNIT MAIN RX-1-UNIT...
- Page 4 When installing the filters (XF-128CN/ XF-128SN) on the MAIN side（RX-1-UNIT) 4. Insert the filter in the specified position as shown below and solder it. ※ Cut the lead of the filters to 2.0 mm or less, after installation. MAIN RX-1-UNIT XF05 Please install the filters in correct direction.
- Page 5 When installing the filters (XF-128CN/ XF-128SN) on the MAIN side（RX- 1-UNIT) 5. Re-assemble the RX-1-UNIT to the chassis. Fix and tighten the srews in order 1 → 2 → 3 → 4. For the rest screws, there is no specific order. 5.0kgf・cm {0.49Ｎ・m} ③...
- Page 6 When installing the filters (XF-128CN/ XF-128SN) on the MAIN Ｊ03 Ｊ02 side（RX-1-UNIT) Marking : marking： Green none 6. Reconnect the cables to the connector of RX-1-UNIT. Coaxial ：7 place FFC cable：2 place Ｊ01 marking：red ※Pass 4 coaxial cables under the lead clamp.。 Ｊ09 marking：...
- Page 7 When installing the filters (XF-129CN/ XF-129SN) on the MAIN Ｊ02(MP) Ｊ03(MP) marking： side（RX-2-UNIT) marking： none green 2.Remove the RX-2-UNIT cable. Coaxial ：4 cables(w/o VCT-101), 6 cables (w/VCT-101) FFC cable：1 cables (w/o VCT-101), 2 cables (w/VCT-101) Ｊ01 marking：blue Ｊ09 marking： black MAIN RX-1-UNIT RX-2-UNIT...
- Page 8 When installing the filters (XF-129CN/ XF-129SN) on the MAIN side（RX-2-UNIT) 3. Remove 6 Screws and remove the RX-2-UNIT from the chassis. MAIN RX-1-UNIT RX-2-UNIT RX-2-UNIT...
- Page 9 When installing the filters (XF-129CN/ XF-129SN) on the MAIN side（RX-2-UNIT) 4. Insert the filter in the specified positions and solder it. ※ Cut the lead of filters to 2.0 mm or less, after the installation. RX-2-UNIT XF05 Please install the filters in correct direction.
- Page 10 When installing the filters (XF-129CN/ XF-129SN) on the MAIN side（RX-2-UNIT) 5. Attach the RX-2-UNIT to the chassis. Fix and tighten the screws in order 1 → 2 → 3 → 4. For the rest of screws, there is no specific order. 5.0kgf・cm {0.49Ｎ・m} ③...
- Page 11 When installing the filters (XF-129CN/ XF-129SN) on the MAIN Ｊ02(MP) Ｊ03(MP) side（RX-2-UNIT) marking：none marking： green 6. Reconnect the cables to the connector of the RX-2-UNIT. Coaxial ：4 cables(w/o VCT-101), 6 cables(w/VCT-101) Ｊ01 FFC cable：1 cables(w/o VCT-101), 2 cables(w/VCT-101) marking： blue ※Pass 4 coaxial cables under the lead clamp Ｊ09 marking：...
- Page 12 7. Make sure that all cable are within the top line of the Insert the coaxial chassis in order to avoid the cables be caught between chassis and case. between the board and the chassis. : the positions you should specially make sure...
- Page 13 8. Reassemble the bottom case with 16 screws. ※ Slightly pushing in the direction of the arrow, tighten in order 1 → 2 → 3 → 4. ※ For the rest of screws, there are no specified order. 8.0kgf・cm {0.78Ｎ・m} Press to the front...