Page 1
While we believe the information in this manual to be cor- Board Unit (Schematics, Layouts & Parts) rect, YAESU assumes no liability for damage that may oc- MAIN Unit cur as a result of typographical or other errors that may be FINAL Unit present.
Page 2
±5.0 kHz/±2.5 kHz (Narrow) Maximum FM Deviation: Better than –50 dB (1.8 MHz - 29.7 MHz Amateur bands) Harmonic Radiation: Better than –63 dB (50 MHz Amateur band) Better than –60 dB (70 MHz UK Amateur band) At least 60 dB below peak output SSB Carrier Suppression: Undesired Sideband Suppression: At least 60 dB below peak output –31 dB @ 14 MHz 100 W PEP 3rd-order IMD: 3 kHz (LSB/USB), 500 Hz (CW), 6 kHz (AM), 16 kHz (FM) Bandwidth: Not more than –6 dB from 300 to 2700 Hz Audio Response (SSB): Microphone Impedance: 600 Ohms (200 to 10 kOhms) FTDX10 Technical Supplement SPESIFICATIONS -1...
Page 3
Audio Output Impedance: 4 to 16 Ohms (4 Ohms: nominal) Less than 4 nW Conducted Radiation: Specifications are subject to change, in the interest of technical improvement, without notice or obligation, and are guaranteed only within the amateur bands. FTDX10 Technical Supplement SPESIFICATIONS -2...
Page 4
PAN TAPTITE-B M2X5NI#2 GUIDE WASHER (POLYSLIDER) ③ U44206001 PAN HEAD TAPTITE-B M2.6X6 ④ U9900117 PAN HEAD TAPTITE-B M2X4NI #2 Non-designated parts are available only as part of a designated assembly. RA6339400 KNOB MAIN ASSY RA6358900 RUBBER RING(MAIN) EXPLODED VIEW -1 FTDX10 Technical Supplement...
Page 5
MAIN-Unit Connect to J1015 on the MAIN-Unit T9207936 Connect to J1016 WIRE ASSY:AH068H-70MM40P on the MAIN-Unit CD1234001 T9207939 T9207338 ENC-A-UNIT WIRE ASSY:AH068H-480MM20P WIRE ASSY AH025H 120MM T9207942 WIRE ASSY:AH068H-40MM6P T9207716 WIRE ASSY AH065H 40MM12P EXPLODED VIEW -2 FTDX10 Technical Supplement...
Page 6
⑥ ⑥ RA602540A PORON SHEET (10x115) RA6310700 CHASSIS P1091172B CONNECTOR RA602540A PORON SHEET (10x115) ② ② ② ② ② ② ② RA6311200 SHIELD PLATE(MAIN) RA0471500 ② ELEC. COND TAPE(C) ② RA0994000 PORON SHEET(151505) ② EXPLODED VIEW -3 FTDX10 Technical Supplement...
Page 7
WIRE ASSY ① CS2680701 ① RA6260900 ⑥ R3100700B PORON SHEET(5X40) FOOT ⑤ ⑤ DC-DC-UNIT ① ⑤ R0145630 STAND ⑤ RA6311300 BOTTOM CASE ⑤ ⑤ RA6336600 PORON SHEET(10X35) ⑤ BOTTOM-CASE-ASSY CQ1136001 RA6334300 ThermalConductivePad RA6310700 CHASSIS EXPLODED VIEW -4 FTDX10 Technical Supplement...
Page 10
DC Voltmeter DC Ammeter (30 A) Ohmmeter 50-Ohm Dummy Load (100/200 watts) In-Line Wattmeter (150/300 watts, 50-Ohm) Linear Detector RF Coupler 4-Ohm AF Dummy Load (3 watts) 1/4-inch 3-contact Plug Important Notice Do not adjust the alignment menus that are not mentioned in this manual. FTDX10 Technical Supplement ALIGNMENT -1...
Page 11
Press the PTT button, then press the [FUNC] Connect the DC voltmeter to TP4004 or TP4005 on the FINAL-Unit. knob. Rotate the [MPVD] ring so that the VDD meter Press and hold in the [STEP/MCH], [C.S] and reading is “13.8 V”. [FINE] keys, while turning the radio ON, to en- Release the PTT button. ter the alignment mode. Press and hold in the [FUNC] knob to save the Rotate the [FUNC] knob to select the alignment new setting and exit the alignment mode. parameter “1-001 VDD MTR”. TP4005 TP4004 FTDX10 Technical Supplement ALIGNMENT -2...
Page 12
Connect the frequency counter to TP1097 on Rotate the [MPVD] ring so that the frequency the MAIN Unit. counter reading is “250.000000 ±20 Hz”. Press and hold in the [STEP/MCH], [C.S] and Press and hold in the [FUNC] knob to save the new setting and exit the alignment mode. [FINE] keys, while turning the radio ON, to en- ter the alignment mode. Rotate the [FUNC] knob to select the alignment parameter “1-003 FREQ.”. TP1097 FTDX10 Technical Supplement ALIGNMENT -3...
Page 13
MAIN Unit. Rotate the [FUNC] knob to select the alignment Set the frequency to 7.15 MHz. parameter “2-004 Local 28”. Rotate the [FUNC] knob to select the alignment Rotate the [MPVD] ring so that the DC voltme- parameter “2-001 Local 7”. ter reading is “1.40 V (±0.05 V)”. Rotate the [MPVD] ring so that the DC voltme- Set the frequency to 50.50 MHz. ter reading is “1.50 V (±0.05 V)”. Rotate the [FUNC] knob to select the alignment Set the frequency to 14.20 MHz. parameter “2-005 Local 50”. Rotate the [FUNC] knob to select the alignment Rotate the [MPVD] ring so that the DC voltme- parameter “2-002 Local 14”. ter reading is “1.40 V (±0.05 V)”. Rotate the [MPVD] ring so that the DC voltme- Press and hold in the [FUNC] knob to save the ter reading is “1.50 V (±0.05 V)”. new setting and exit the alignment mode. TP3005 FTDX10 Technical Supplement ALIGNMENT -4...
Page 14
Connect the DC voltmeter to TP2519 on the Rotate the [MPVD] ring so that the DC voltme- MAIN Unit. ter reading is “1.90 V (±0.1 V)”. Set the frequency to 7.050 MHz in the CW-U Set the frequency to 28.700 MHz in the CW-U mode. mode. Rotate the [FUNC] knob to select the alignment Rotate the [FUNC] knob to select the alignment parameter “2-006 RF-AGC 7”. parameter “2-009 RF-AGC 28”. TP2519 FTDX10 Technical Supplement ALIGNMENT -5...
Page 15
Rotate the [MPVD] ring so that the DC voltme- Connect the DC voltmeter to TP2520 on the MAIN Unit. ter reading is “1.90 V (±0.1 V)”. Set the frequency to 14.200 MHz. Press and hold in the [FUNC] knob to save the Adjust VR2501 on the MAIN Unit so that the new setting and exit the alignment mode. DC voltmeter reading is “1.50 V (±0.03 V)”. Press and hold in the [FUNC] knob to save the new setting and exit the alignment mode. VR2501 TP2520 FTDX10 Technical Supplement ALIGNMENT -6...
Page 16
2-024 S-MTR +40 +76 dbµ S9+40 2-015 IF-AGC 50 51.900 MHz, 3 dBµ 51.900 MHz -2.0 dB ± 0.5 dB 2-025 S-MTR +50 +86 dbµ S9+50 2-026 S-MTR +60 +96 dbµ S9+60 Press and hold in the [FUNC] knob to save the new setting and exit the alignment mode. FTDX10 Technical Supplement ALIGNMENT -7...
Page 17
[R.FLT] : 3 kHz Rotate the [FUNC] knob to select the alignment [WIDTH] : 2.4 kHz parameter “2-036 FM GAIN S1 50”. Rotate the [FUNC] knob to select the alignment Set the frequency to 51.500 MHz. parameter “2-033 SDR GAIN 3k”. Rotate the [MPVD] ring so that the S-meter Rotate the [MPVD] ring to set the “0”. reading is “S1”. Set the following controls as indicated: Press and hold in the [FUNC] knob to save the [R.FLT] : 12 kHz new setting and exit the alignment mode. [WIDTH] : 2.4 kHz Rotate the [FUNC] knob to select the alignment parameter “2-034 SDR GAIN 12k”. Rotate the [MPVD] ring to set the “0”. FTDX10 Technical Supplement ALIGNMENT -8...
Page 18
Rotate the [FUNC] knob to select the alignment new setting and exit the alignment mode. parameter “2-038 FM SQL THN”. Press the [FUNC] knob. L3098 VR3001 Set the RF Signal Generator to 0 dBµ at the 51.500 MHz of a 1 kHz ±3.5 kHz deviation FM modulation audio signal. Set the Main Band frequency to 51.500 MHz in the FM-Wide mode. Rotate the [FUNC] knob to select the alignment parameter “2-039 FM SQL TI”. Press the [FUNC] knob. Press and hold in the [FUNC] knob to save the new setting and exit the alignment mode. FTDX10 Technical Supplement ALIGNMENT -9...
Page 19
Press and hold the PTT button then adjust the [MPVD] ring so that the DC ammeter reading [MPVD] ring so that the DC ammeter reading is “100 mA (±10 mA)”. is “500 mA (±50 mA)”. Release the PTT button. Release the PTT button. Rotate the [FUNC] knob to select the alignment parameter “3-007 VHF PREDR BIAS”. J4001 J4004 J4005 FTDX10 Technical Supplement ALIGNMENT -10...
Page 20
Disconnect the 50-Ohm resistors from J4001, Rotate the [FUNC] knob to select the alignment then connect the coaxial cables to J4001. parameter “3-006 HF FINAL BIAS”. Re-connect the jumper plugs to J4004 and J4005. Press and hold the PTT button then adjust the Re-connect the plug to J4006. [MPVD] ring so that the DC ammeter reading is “1.5 A (±150 mA)”. Release the PTT button. J4006 FTDX10 Technical Supplement ALIGNMENT -11...
Page 21
Turn off the [TUNE] switch, then set the fre- 0.1 V). quency to 24.900 MHz in the CW-U mode. Release the PTT button. Press and hold in the [STEP/MCH], [C.S] and Press and hold in the [FUNC] knob to save the [FINE] keys, while turning the radio ON, to en- new setting and exit the alignment mode. ter the alignment mode. TC4001 J4020 FTDX10 Technical Supplement ALIGNMENT -12...
Page 22
“3-014 I-ALC 14” for the 14 MHz amateur band's ALC Adjustment. Press and hold in the [FUNC] knob to save the Set the frequency to 14.000 MHz. new setting and exit the alignment mode. Key the transmitter, then adjusting the [MPVD] ring for 110 W on the Wattmeter. Unkey the transmitter. Rotate the [FUNC] knob to select the alignment parameter “3-015 I-ALC 18” for the 18 MHz amateur band's ALC Adjustment. Set the frequency to 18.118 MHz. Key the transmitter, then adjusting the [MPVD] ring for 110 W on the Wattmeter. Unkey the transmitter. FTDX10 Technical Supplement ALIGNMENT -13...
Page 23
“3-035 5W TXG 1.8” as indicated by the chart exit the alignment mode. on the next page. Perform the same procedures for the Alignment parameter “3-036 100W FALC 3.5” through “3-170 5W TXG 50” (UK version: “3-182 5W TXG 70”) as indicated by the chart on the next page. Press and hold in the [FUNC] knob to save the new setting and exit the alignment mode. FTDX10 Technical Supplement ALIGNMENT -14...
Page 24
10 W (+1 W/-0 W) 3-076 10 W 3-136 10 W Maximum deflection Maximum deflection 3-077 3-137 3-078 5 W (+1 W/-0 W) 3-138 5 W (+1 W/-0 W) 3-079 3-139 Maximum deflection Maximum deflection 3-080 3-140 FTDX10 Technical Supplement ALIGNMENT -15...
Page 25
3-180 5 W (+1 W/-0 W) 3-181 ment parameter “3-193 REV ALC 70”. 3-182 S8 - S9 Key the transmitter, then rotate the [MPVD] ring so that the PO meter (on the front pan- el) reading is 25 W (+0 W/-10 W). Unkey the transmitter. Press and hold in the [FUNC] knob to save the new setting and exit the alignment mode. FTDX10 Technical Supplement ALIGNMENT -16...
Page 26
Rotate the [FUNC] knob to select the alignment [FINE] keys, while turning the radio ON, to en- parameter “3-196 FM-N DEV”. ter the alignment mode. Rotate the [MPVD] ring so that the parameter Rotate the [FUNC] knob to select the alignment parameter “3-200 SWR-MTR CO 1.8”. indication “100”. Press and hold in the [FUNC] knob to save the Rotate the [MPVD] ring so that the parameter new setting and exit the alignment mode. indication “128”. J4020 FTDX10 Technical Supplement ALIGNMENT -17...
Page 27
[MPVD] ring so that the SWR meter (on the front panel) reading is “3.0.” The SWR meter reading (3.0) is broad (few points). Therefore, set the [MPVD] ring to the center of this broad range. Release the PTT button. Perform the same procedures for the Alignment Menus “3-201 SWR-MTR1.5 14” through “3- 203 SWR-MTR3.0 14”, “3-205 SWR-MTR1.5 50” through “3-207 SWR-MTR3.0 50”. FTDX10 Technical Supplement ALIGNMENT -18...
Page 28
2-028 FIL GAIN 0.5k ring for “20 dB” on the COMP meter. 2-029 FIL GAIN 3k Rotate the [FUNC] knob to select the alignment 2-030 FIL GAIN 12k parameter “3-212 COMP MTR 30dB”. Key the transmitter, then rotate the [MPVD] ring so that the COMP meter deflects to full scale. Press and hold in the [FUNC] knob to save the new setting and exit the alignment mode. FTDX10 Technical Supplement ALIGNMENT -19...
Page 29
MAIN Unit Circuit Diagram (MAIN Unit/CNTL) FTDX10 Technical Supplement MAIN -1...
Page 30
MAIN Unit Circuit Diagram (MAIN Unit/DVI) FTDX10 Technical Supplement MAIN -2...
Page 31
MAIN Unit Circuit Diagram (MAIN Unit/DSP) FTDX10 Technical Supplement MAIN -3...
Page 32
MAIN Unit Circuit Diagram (MAIN Unit/AF) FTDX10 Technical Supplement MAIN -4...
Page 33
MAIN Unit Circuit Diagram (MAIN Unit/RX) MAIN -5 FTDX10 Technical Supplement...
Page 34
MAIN Unit Parts Layout (side A) FTDX10 Technical Supplement MAIN -6...
Page 35
MAIN Unit Parts Layout (side B) FTDX10 Technical Supplement MAIN -7...
Page 36
K22178809 C 1201 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 1202 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 1207 CHIP CAP. GRM155R61E105KE11D K22149010 C 1210 CHIP CAP. 0.0033uF GRM155B11H332KA01D K22178815 C 1211 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 FTDX10 Technical Supplement MAIN -8...
Page 37
CHIP CAP. GRM1552C1H5R0CA01D K22178207 C 1367 CHIP CAP. GRM1552C1H5R0CA01D K22178207 C 1368 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 1369 CHIP CAP. GRM1553C1H3R0CA01D K22178205 C 1370 CHIP CAP. GRM155B31A105KE15D K22108809 C 1371 CHIP TA.CAP. TMCSA1C105MTRF K78120009 FTDX10 Technical Supplement MAIN -9...
Page 38
C 1688 CHIP CAP. 22uF GRM21BR61E226ME44L K22140830 C 1689 CHIP CAP. 22uF GRM21BR61E226ME44L K22140830 C 1690 CHIP CAP. 22uF GRM21BR61E226ME44L K22140830 C 1691 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 1692 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 FTDX10 Technical Supplement MAIN -10...
Page 39
C 2029 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2030 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2031 CHIP CAP. 10uF GRM188B31A106ME69D K22104810 C 2032 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2033 CHIP CAP. 10uF GRM188B31A106ME69D K22104810 FTDX10 Technical Supplement MAIN -11...
Page 40
C 2117 CHIP CAP. 0.001uF GRM1555C1H102JA01D K22179756 C 2118 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2244 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2245 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2247 CHIP TA.CAP. 22uF TPSB226M016Y0600 K78120075 FTDX10 Technical Supplement MAIN -12...
Page 41
C 2576 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2579 CHIP CAP. 4.7uF 6.3V JMK107BJ475MA-T K22084803 C 2580 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 2581 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2582 CHIP CAP. 0.001uF GRM155B11H102KA01D K22178809 FTDX10 Technical Supplement MAIN -13...
Page 42
EEE1CA470SP K48120005 C 2667 CHIP CAP. GRM155R61E105KE11D K22149010 C 2670 AL.ELECTRO.CAP. 470uF 16CE470BS K48120035 C 2675 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 2676 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2678 CHIP CAP. 10uF GRM188R61E106MA73D K22144818 FTDX10 Technical Supplement MAIN -14...
Page 43
K22178809 C 2795 CHIP CAP. GRM155B31C105KA12D K22128817 C 2796 CHIP CAP. 0.001uF GRM155B11H102KA01D K22178809 C 2797 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 2798 CHIP CAP. 10uF GRM188R61E106MA73D K22144818 C 2799 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 FTDX10 Technical Supplement MAIN -15...
Page 44
K22149010 C 3079 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3080 CHIP CAP. GRM155R61E105KE11D K22149010 C 3081 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3082 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3083 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 FTDX10 Technical Supplement MAIN -16...
Page 45
C 3165 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3166 CHIP CAP. 0.0015uF GRM1555C1H152JA01D K22179760 C 3167 CHIP CAP. 0.0018uF GRM1555C1H182JA01D K22179762 C 3168 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3169 CHIP CAP. 33pF GRM1552C1H330JA01D K22178224 FTDX10 Technical Supplement MAIN -17...
Page 46
C 3252 CHIP CAP. 0.001uF GRM1555C1H102JA01D K22179756 C 3253 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3254 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3255 CHIP CAP. 470pF GRM1555C1H471JA01D K22179748 C 3256 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 FTDX10 Technical Supplement MAIN -18...
Page 47
K22178216 C 3328 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3329 CHIP CAP. 0.0012uF GRM1555C1H122JA01D K22179758 C 3331 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3332 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3333 CHIP CAP. GRM1552C1H6R0DA01D K22178208 FTDX10 Technical Supplement MAIN -19...
Page 48
C 3428 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3429 CHIP CAP. 0.001uF GRM1555C1H102JA01D K22179756 C 3430 CHIP CAP. 0.001uF GRM155B11H102KA01D K22178809 C 3431 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3432 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 FTDX10 Technical Supplement MAIN -20...
Page 49
K22178848 C 3509 CHIP CAP. 0.001uF GRM155B11H102KA01D K22178809 C 3510 CHIP CAP. 0.001uF GRM155B11H102KA01D K22178809 C 3512 CHIP CAP. GRM1552C1H5R0CA01D K22178207 C 3513 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3514 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 FTDX10 Technical Supplement MAIN -21...
Page 50
GRM155R71H104KE14D K22178872 C 3592 CHIP CAP. GRM1552C1H9R0DA01D K22178211 C 3593 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3594 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3595 AL.ELECTRO.CAP. 220uF HV221M016E077ETR K48120041 C 3596 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 FTDX10 Technical Supplement MAIN -22...
Page 51
K22178872 C 3706 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3707 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3708 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3709 CHIP CAP. 0.01uF GRM155R71H103KA88D K22178848 C 3710 CHIP CAP. GRM155R61E105KE11D K22149010 FTDX10 Technical Supplement MAIN -23...
Page 52
C 3835 CHIP CAP. 0.1uF GRM155R71H104KE14D K22178872 C 3836 CHIP CAP. 10uF GRM188R61E106MA73D K22144818 C 3840 CHIP CAP. 10pF GRM1552C1H100JA01D K22178212 C 3841 CHIP CAP. 22pF GRM1552C1H220JA01D K22178220 C 3842 CHIP CAP. 10pF GRM1552C1H100JA01D K22178212 FTDX10 Technical Supplement MAIN -24...
Page 53
D 2529 DIODE 1SS355 TE-17 G2070470 D 2530 DIODE 1SS389(TPL3.F) G2070608 D 3001 SURGE ABSORBER 1608SGXA2-TR2 Q9000891 D 3002 DIODE RN142S TE61 G2070994 D 3003 DIODE RN142S TE61 G2070994 D 3004 DIODE RN142S TE61 G2070994 FTDX10 Technical Supplement MAIN -25...
Page 119
RMC1/16SK102FTH J24189487 R 9535 CHIP RES. 1/16W RMC1/16SK563FTH J24189526 R 9536 CHIP RES. 1/10W RMC1/10T 000J J24205000 R 9540 CHIP RES. 1/16W RMC1/16S JPTH J24189070 SC9501 SHIELD CASE (25X39) RA619230A SC9502 SHIELD CASE (25X39) RA619230A FTDX10 Technical Supplement DC-DC -4...
Page 120
Copyright 2021 YAESU MUSEN CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of YAESU MUSEN CO., LTD. YAESU MUSEN CO., LTD. Tennozu Parkside Building 2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan YAESU USA 6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
Need help?
Do you have a question about the FTDX10 and is the answer not in the manual?
Questions and answers