Adjustment Progress Messages - Sony Digital betacam DVW-970 Operation Manual

Item
DISP DC IN
DISP 16:9/4:3 ID
DISP WRR RF LVL Displays the reception level of the
DISP E. MARK IND Displayed when an essence mark
DISP TIME CODE
DISP VIDEO RATE Displays the recording video
1) When an Anton Bauer Intelligent Battery System or the BP-GL65/
GL95/L60S battery pack is used, the setting of this item determines
the display as follows:
INT: The remaining battery capacity is shown as a percentage when
there is a change, and when the capacity is low.
AUTO: The remaining battery capacity is shown as a percentage,
except that when this is impossible the battery voltage appears.
VOLT: The battery voltage is shown.
3
Turn the MENU knob to move the
you want to set, and press the MENU knob.
b
The mark on the left of the selected item changes to
a z mark, and the z mark on the left of the setting
changes to a ? mark.
4
Turn the MENU knob to select whether the selected
item should appear in the viewfinder display (the
"ON" setting), or not appear (the "OFF" setting), and
press the MENU knob.
The z mark returns to a
returns to a z mark.
Note that pressing the CANCEL/PRST / ESCAPE
switch to CANCEL/PRST on this page has no effect.
5
To set another item to "ON" or "OFF," repeat steps 3
and 4.
6
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
The menu disappears from the viewfinder screen, and
the display indicating the current status of the
camcorder appears along the top and bottom of the
screen.
80
Status Display on the Viewfinder Screen
Description
Displayed when the power is
supplied from an external battery
connected to the DC IN
connector.
Displays the 16:9/4:3 mode
indicator.
wireless microphone.
has been recorded.
Displays the time code.
signal rate.
b
mark to the item
b
mark, and the ? mark
5-2-3 Display Modes and Setting
Change Confirmation/Adjustment
Progress Messages
You can limit or suppress the messages that give details of
setting changes and adjustment progress and results by
setting a display mode.
The conditions under which messages are displayed and
their correspondence with the display mode are as follows:
Setting change confirmation/adjustment progress messages
and display modes
Y: Message is displayed.
N: Message is not displayed.
Message Message
display
condition
When the filter ND : n, CC : m
selection has (where n = 1, 2, 3, 4,
been changed m = A, B, C, D)
When the gain GAIN : n (where n =
setting has been –3 dB, 0 dB, 3 dB, 6 dB,
changed 9 dB,12 dB, 18 dB, 24 dB,
30 dB, 36 dB, 42 dB,
48 dB)
When the WHITE : n
setting of the (where n = A CH, B CH,
WHITE BAL PRESET)
switch has been or ATW : RUN
changed
When the DCC : ON (or OFF)
OUTPUT/DCC
selector has
been set to DCC
ON or OFF
When the SS : 1/100 (DVW-970) or
shutter speed 1/60 (DVW-970P)
and mode (or 1/125, 1/250, 1/500,
setting has been 1/1000, 1/2000, ECS,
1) SLS)
changed
When the black E.g. AWB : OK
or white balance
has been
2)
adjusted
1) This is also displayed for about 3 seconds when the SHUTTER selector is
set to ON.
2) For details, see "4-1 Adjusting the Black Balance and the White Balance"
on page 56.
Changing the display mode
The currently set display mode appears on the VF DISP 1
page of the USER menu. To change it, proceed as follows:
1
Follow steps 1 and 2 in "5-2-2 Selecting the Display
Items" (page 79), until the VF DISP 1 page of the
USER menu appears on the screen.
Display
mode setting
1 2 3
N N Y
N N Y
N N Y
N Y Y
N Y Y
N Y Y