Sony Digital betacam DVW-970 Operation Manual page 78

c Color temperature
This indicates the currently selected color temperature.
d UHF wireless microphone reception level
This indicates reception level of the wireless microphone
when the UHF wireless microphone is attached, using four
x which appear at the right of "W." When four x are lit,
the receiving condition is good.
e DC IN / battery voltage or remaining capacity
This shows the battery voltage or remaining capacity of an
internal battery pack.
When the power is supplied from an AC adaptor connected
to the DC IN connector, "DC IN" appears.
When the DISP BATT REMAIN item is set to "INT" on
the VF DISP 2 page of the USER menu, the battery voltage
is not indicated. However, when the Anton Bauer
intelligent battery system or the BP-GL65/GL95/L60S
battery pack is used, the remaining battery capacity is
automatically detected and indicated as a percentage even
when the DISP BATT REMAIN item is set to "OFF." The
indicated value changes in steps of 10%.
• Until the remaining battery capacity is reduced to 40%,
the indications MAX, 90%, 80%...40% are displayed for
3 seconds in the viewfinder each time the remaining
battery capacity reduces by 10%.
• When the remaining battery capacity is less than 40%,
the indication is displayed all the time.
• When the remaining battery capacity is less than 10%
the indication flashes. When the remaining battery
capacity is reduced further, the LOW indication flashes.
1) This value can be set to either 10% or 20% on the FUNCTION 2 page of
the OPERATION menu.
f Essence mark indication
This appears when an essence mark has been recorded.
g * indicator
This flashes when the color bars are displayed and is
recorded together with the color bars.
h 16:9 mode recording indicator
This indicates recording in the 16:9 mode. This indicator is
recorded together with the color bars.
i Setting change and adjustment progress message
display area
For details, see "5-2-3 Display Modes and Setting Change
Confirmation/Adjustment Progress Messages" on page 80.
j Operation/error message display area
For details, see "Operation/error messages" on page 130.
k Iris setting/auto iris override
This indicates the f-stop (iris setting) of the lens.
78
Status Display on the Viewfinder Screen
Also, the auto iris override is displayed using bars which
appear in the upper and lower parts to the left of the F
number respectively.
For details, see "4-3 Changing the Reference Value for
Automatic Iris Adjustment" on page 62.
l Remaining tape
This indicator indicates the remaining tape recording time
(in minutes) of the VTR.
Examples of remaining disc recording time indication
Indication
F – 30
30 – 25
25 – 20
20 – 15
15 – 10
10 – 5
5 – 0
5 – 0 (flashing)
m Audio level
These indicate the level of audio channel 1 and channel 2.
The peak indication of the VTR level meter is related as
follows to the audio level when an 1-kHz sine wave is
1)
,
input.
Audio channel 1
level indicator
Audio channel 2
level indicator
VTR level meter
indicator
n Shutter speed
This indicates the shutter speed or the shutter mode.
However, if the SHUTTER selector is set to OFF, nothing
is displayed.
1/100 (DVW-970) or 1/60 (DVW-970P), 1/125, 1/250,
1/500, 1/1000, 1/2000: Shutter speed (in seconds) in
standard mode
ECS: ECS mode
EVS: EVS mode
1F to 8F, 16F: Number of frames in SLS mode
o Gain
This indicates the gain of the video amplifier, as set by the
GAIN selector.
p White balance memory
This indicates the currently selected white balance
automatic adjustment memory.
A: Displayed when the WHITE BAL switch is set to A.
B: Displayed when the WHITE BAL switch is set to B.
Remaining disc recording time
Full to 30 minutes
30 to 25 minutes
25 to 20 minutes
20 to 15 minutes
15 to 10 minutes
10 to 5 minutes
5 to 2 minutes
2 to 0 minute
1
2