Change Confirmation/Adjustment Progress Messages; Setting The Marker Display - Sony PDW-F335L Operating Instructions Manual

INT: When one of the above batteries is installed, the remaining
power is shown as a percentage value (%) when there is a change
in the value or when the power is low.
AUTO: The remaining power is shown as a percentage value (%)
when one of the above batteries is installed. Otherwise the voltage
(VOLT) is displayed continuously.
VOLT: The voltage (VOLT) is displayed continuously.
VF DISP 2 page
Item
DISP 5600K
DISP FILTER
DISP WHITE
DISP GAIN
DISP SHUTTER
DISP AUDIO
DISP DISC
DISP IRIS
DISP LOW LIGHT
DISP INTERVAL
3
Turn the MENU knob to select the desired setting
(ON, OFF, or value), and press the MENU knob.
4
Repeat steps 2 and 3 until you have set all of the
desired items.
Change Confirmation/Adjustment
Progress Messages
The messages indicating setting changes, progress and
consequence of adjustments, and the situations indicated
by these messages are as follows.
Setting change confirmation/adjustment progress
messages
Situation
The filter selection has been
changed
The gain setting has been
changed
The setting of the WHITE
BAL switch has been
changed
The OUTPUT/DCC switches
has been set to DCC ON or
OFF
138
Setting the Status Display on the Viewfinder Screen and the LCD Monitor
Description
Displays "5600K".
Displays types of the ND filter.
Displays selected white balance
memory.
Displays gain value.
Displays shutter speed and ECS
mode.
Displays audio level.
Displays remaining disc capacity.
Lens iris setting indication
"LOW LIGHT" indication when the
average video level is below a
certain threshold.
"INTERVAL TIME" indication
during interval recording.
Message to appear
FILTER: n
(where n = 1, 2, 3, 4)
GAIN: n
(where n = –3dB, 0dB, 3dB,
6dB, 9dB,12dB, 18dB, 24dB,
30dB, 36dB, 42dB, 48dB)
WHITE: n
(where n = A CH, B CH,
PRESET) or ATW: RUN
DCC: ON (or OFF)
Situation
The shutter speed and mode
1)
setting has been changed
The black or white balance
has been adjusted
1) The corresponding message is also displayed for about 3 seconds when the
SHUTTER switch is set to ON.

Setting the Marker Display

You can switch the display of the center and safety zone
markers on or off and select whether the area indicated by
the safety zone marker is 80%, 90%, 92.5%, or 95% of the
screen area.
(How to select an item in the menu screen: Turn the
MENU knob to move the b mark to the desired item.)
1
Display the MARKER page of the USER (or
OPERATION) menu, and press the MENU knob.
For details on menu operations, see "Basic Menu
Operations" on page 132.
2
Select the desired setting item, and press the MENU
knob.
You can set the following items on the MARKER
page.
Item Description
MARKER If you want no markers to be
displayed, set to OFF.
CENTER To display the center marker, set
to ON.
SAFETY ZONE To display the safety zone, set to
ON.
SAFETY AREA Selects the safety zone area.
ASPECT To display the aspect marker, set
to ON.
ASPECT SELECT Selects the type of the aspect
marker. (14:9/13:9/4:3)
3
Turn the MENU knob to select the desired setting, and
press the MENU knob.
4
Repeat steps 2 and 3 until you have set all of the
desired items.
Message to appear
SHUTTER: 1/100 (or 1/125,
1/250, 1/500, 1/1000, 1/2000,
ECS, SLS)
E.g. WHITE: OK