Configuring Cisco G.shdsl Efm/Atm - Cisco EHWIC-4SHDSL-EA Configuration Manual

Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2
GDF Ring 3 Registers:
GDF Error Interrupt Enable Register (0x0000):
GDF Error Interrupt Event Register (0x0000):
HWIC ID:
HWIC Revision: 0x0
HWIC Status:
HWIC DDR TXCRC:0x0
HWIC Control:
HWIC Interrupt Event: 0x0
HWIC Diag 1: 0x0
HWIC Diag 2: 0x1C05
******* HWIC Rx/Tx Rings *******
rxr @(1DAD4800) head (0) tail (0) entries (64) serviced (0)
txr @(1DAD4000) head (7) tail (7) entries (64) serviced (7) count (0)
bd(1DAD4800): flags 0000 length 0000 address 1CE8D780
<Output abbreviated due to space constraints>
ATM Mode
The following examples show the output of a 2-wire configuration in ATM mode.
•
•
show controllers shdsl
Router# sh controllers shdsl 0/3/0
Controller SHDSL 0/3/0 is UP
Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 3
Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G
TXQueueTailBase Register
TxQueueBase
TxQueueSize
RxQueueHeadBase Register
RxQueueBase
RxQueueSize
RxBufferSize
RxQueueLowWaterMark
HWICQueueConfig Register
TXQueueTailBase Register
TxQueueBase
TxQueueSize
RxQueueHeadBase Register
RxQueueBase
RxQueueSize
RxBufferSize
RxQueueLowWaterMark
GDF Rx Resume Error Int
GDF Tx First/Last Error Int
GDF Rx Resume Error Event
GDF Tx First/Last Error Event 0x00
******* HWIC Common Registers at EC600000 *******
0x2
0x0
0xC000
DDR Enable
Interrupt Module Reset
DMA Module Reset
IRQ2 Global Int Mask
DDR TXCRC Int Mask
TX Fifo Overrun Int Mask 0
DDR TXCRC Int
TX Fifo Overrun Int
show controllers shdsl
show controllers atm
ATM: 2-wire, Mpair, IMA, Annex A, B, F & G
0x0000
0x00 TxQueueTail
0x00 TxQueueHead
0x0000
0x00 RxQueueHead
0x00 RxQueueTail
0x0000 RxQueueHighWaterMark
0x00
0x0000 HWICQueueBase
0x0000
0x00 TxQueueTail
0x00 TxQueueHead
0x0000
0x00 RxQueueHead
0x00 RxQueueTail
0x0000 RxQueueHighWaterMark
0x00
0x00 GDF Rx Done Error Int
0x00 GDF Tx Done Error Int
0x00 GDF Rx Done Error Event
GDF Tx Done Error Event
1 Software Reset
0 GDF Module Reset
0 Flow Control Reset
0 IRQ1 Global Int Mask
0 DDR TXClk Loss Int Mask 0
0 DDR TXClk Loss Int
0
Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2

Configuring Cisco G.SHDSL EFM/ATM

0x00
0x00
0x00
0x00
0x00
0x0000
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
1
0
0
0
0
15