Cisco EHWIC-4SHDSL-EA Configuration Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Card
  5. EHWIC-4SHDSL-EA
  6. Configuration manual

Cisco EHWIC-4SHDSL-EA Configuration Manual

Enhanced high-speed wan interface card
Hide thumbs
Table of Contents

Advertisement

Quick Links

Configuring Cisco Multimode G.SHDSL
EFM/ATM in Cisco ISR G2
OL-24505-04
Last Updated: October 14, 2013
This document describes how to configure Cisco G.SHDSL Ethernet in the first mile (EFM) and
Asynchronous Transfer Mode (ATM). Cisco G.SHDSL EFM/ATM Enhanced high-speed WAN interface
card (EHWIC) connect Cisco Integrated Services Routers Generation 2 (ISR G2s) with central office
Digital Subscriber Line Access Multiplexers (DSLAMs) and provide up to four lines of G.SHDSL
(ITU-T 991.2) connectivity. The C888EA provides four pairs of multimode G.SHDSL connectivity.
There is one EHWIC model and one fixed platform model:
•
•
Finding Support Information for Platforms and Cisco IOS Software Images
Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image
support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on
Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at
the login dialog box and follow the instructions that appear.
Contents
This document shows the configuration process for the EHWIC-4SHDSL-EA multimode EFM and ATM
card and the C888EA EFM and ATM mode fixed platform.
•
•
•
•
•
Cisco Systems, Inc.
www.cisco.com
EHWIC-4SHDSL-EA-A double-wide multimode EHWIC G.SHDSL, 4 pair, 802.3ah, EFM and
ATM mode interface card
C888EA-A multimode G.SHDSL, 4 pair 802.3ah, EFM and ATM mode fixed platform

Advertisement

Table of Contents
loading

Related Manuals for Cisco EHWIC-4SHDSL-EA

Summary of Contents for Cisco EHWIC-4SHDSL-EA

  • Page 1: Table Of Contents

    Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

  • Page 2: Prerequisites For Cisco G.shdsl Efm/Atm Ehwics

    Information. Information About Cisco G.SHDSL EFM/ATM Cisco G.SHDSL EFM/ATM EHWICs support up to four pairs of digital subscriber lines (DSL). The fixed platform model (C888EA) also supports up to four pairs. The DSL pairs are bundled in groups and configured in the Cisco IOS command-line interface (CLI) by using the dsl-group command. Selecting the mode is done by using the mode command.
  • Page 3 RJ-45 connector, in EFM or ATM modes. Note The C888EA and the Cisco EHWIC-4SHDSL-EA support the Dying Gasp feature. The term dying gasp refers to power status as defined in ITU-T standard G.991.2, section 7.1.2.5.3.

  • Page 4: Connecting Cisco G.shdsl Efm/Atm To The Network

    DSL groups. Configuring Cisco G.SHDSL EFM/ATM Configure DSL groups for Cisco G.SHDSL EFM/ATM using the Cisco IOS CLI on the router in privileged configuration mode. • Configuring EFM or ATM Mode and a DSL Group, page 5 •...

  • Page 5: Configuring Cisco G.shdsl Efm/Atm" Section

    Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM Configuring EFM or ATM Mode and a DSL Group Use the Cisco IOS CLI on the router in global config-controller mode to configure the mode on the Cisco EHWIC-4SHDSL-EA or the C888EA. Note The dsl-group must be removed before changing from a previously configured mode.

  • Page 6: Configuring The G.shdsl Service On A Cisco Router

    Router(config-controller-dsl-group)# Configuring the G.SHDSL Service on a Cisco Router To configure the G.SHDSL service on the Cisco EHWIC-4SHDSL-EA or C888EA using the Cisco IOS CLI in global configuration mode, follow these steps. Note For EHWICs, use the three-tuple notation (slot number/subslot number/0). For fixed platforms, use the single-tuple notation (slot number).
  • Page 7 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM ip address <IP-address> <subnet mask> exit exit One of the following: show interface ethernet [slot/port-adapter/port] (in EFM mode) • show interface atm [slot/port-adapter/port] (in ATM mode) •...
  • Page 8 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM DETAILED STEPS Command Purpose Step 1 Selects controller and enter DSL group configuration controller shdsl slot number/subslot number/0 mode. For EHWICs, use the three-tuple notation Note Note See the “Configuring Cisco G.SHDSL...
  • Page 9 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM Command Purpose Step 7 For ATM mode: < > < > interface atm slot subslot /<0> Example: Router(config)# interface atm 0/3/0 Router# < > < > Step 8...
  • Page 10 Router# sh controllers shdsl 0/3/0 Controller SHDSL 0/3/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 3 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...
  • Page 11 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM SNR Margin alarm: none Loop Attenuation alarm: none Termination: CPE, Line mode: 2-wire, Annex: B Line coding: 16-TCPAM Configured/actual rate: AUTO/2304 kbps Modem status: UP_DATA_MODE,Condition: GHS_TRANSFER_ Reason: ERR_UNUSED_...
  • Page 12 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM MAC Rx CRC SW filtered pak Multicast related information ------------------------------ Software MAC address filter(hash:length/addr/mask/hits): ------------------------------------------------------- 0x00: ffff.ffff.ffff 0000.0000.0000 0xBB: 0021.1bfc.aea0 0000.0000.0000 0xC0: 0180.c200.0002 0000.0000.0000 0xC0: 0100.0ccc.cccc 0000.0000.0000 0xC5: 0180.c200.0007...
  • Page 13 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM Tx128_to_255 Bytes Packet Count0 Tx256_to_511 Bytes Packet Count 0 Tx512_to_1023 Bytes Packet Count 0 Tx1024_to_1518 Bytes Packet Count 0 TxUndersize Packet Count TxOversize Packet Count Ingress frame counters:...
  • Page 14 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM IRQ2 Int IRQ1 Int Int Frame Network Int 0x01 Error Interrupt Event (0xA94B6BF): GDF Rx Resume Error Event Rx Done Error Event Card Present Change Event Hwic Int Frame Error Event...

  • Page 15: Configuring Cisco G.shdsl Efm/Atm

    Router# sh controllers shdsl 0/3/0 Controller SHDSL 0/3/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 3 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...

  • Page 16: Tx_Bytes

    Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM CPE termination cdb=0x14F0584, plugin=0x14DF8BC, ds=0x12FFBEF0 base=0xEC600000 FPGA Version is A11 NPU Source: System NPU Firmware version: SHDSL_EA_FW_20110906071435 Vendor: Infineon, Chipset: SOCRATES-4e PHY Source: System IDC Firmware version: V1.7.2.0 DFE Firmware version: V-1.1.7.10__2...

  • Page 17: Configuring 2-Wire Non-Bonding Dsl Group

    Configuring 2-Wire Non-bonding DSL Group To configure a 2-wire non-bonding DSL group on a Cisco G.SHDSL EFM/ATM, use the Cisco IOS CLI on the router in global configuration mode. Configuring 2-wire non-bonding DSL group is the same for EFM and ATM modes.
  • Page 18 For more information, refer to the “Command Reference” section on page Examples The following examples use the G.SHDSL commands to configure a 2-wire DSL group on a Cisco EHWIC-4SHDSL-EA or C888EA in ATM and EFM modes. 2-Wire DSL Group Configuration in ATM mode •...

  • Page 19: Configuring Bonding Groups In Atm Mode

    Configuring Bonding Groups in ATM Mode Use the Cisco IOS CLI on the router in global configuration mode to configure bonding groups in the ATM mode on the Cisco EHWIC-4SHDSL-EA, or on the C888EA. There are two types of bonding groups possible in ATM mode: M-pair and IMA.
  • Page 20 Examples The examples in this section show how to configure bonding groups in the ATM mode on the Cisco EHWIC-4SHDSL-EA, or on the C888EA. The examples include: Configuring an M-pair bonding DSL group on a Cisco EHWIC-4SHDSL-EA •...
  • Page 21 • Configuring an IMA bonding group on a C888EA • Configuring an M-pair bonding DSL group on a Cisco EHWIC-4SHDSL-EA The following example shows the G.SHDSL commands used to configure an M-pair bonding DSL group on a Cisco EHWIC-4SHDSL-EA. Router(config)# controller shdsl 0/2/0...

  • Page 22: Configuring Auto Groups In Atm Mode

    Router(config-controller)# exit Router(config)# Configuring Auto Groups in ATM Mode Use the Cisco IOS CLI on the host router in global configuration mode to configure auto groups in the ATM mode on the Cisco EHWIC-4SHDSL-EA, or on the C888EA. Note For IMA configurations, do not use dsl-group auto. Instead, use manual IMA configuration. For more information, see the IMA example in the “Configuring Bonding Groups in ATM Mode”...

  • Page 23: Configuring An Efm-Bonding Group

    Configuring an EFM-Bonding Group Use the Cisco IOS CLI on the router in global configuration mode to configure an EFM-bonding group on the Cisco G.SHDSL EFM/ATM. To ensure a successful EFM-bonding group configuration, confirm that the central office (CO) network Note equipment that is connected with the Cisco G.SHDSL EFM/ATM is configured for EFM-bonding.
  • Page 24 For more information, refer to the “Command Reference” section on page Examples The following example uses the G.SHDSL commands to configure an efm-bonding group on a Cisco EHWIC-4SHDSL-EA. Router(config)# controller shdsl 0/2/0 Router(config-controller)# mode efm Router(config-controller)# dsl-group 0 pairs 0 efm-bond Router(config-controller-dsl-group)# *Oct 1 10:49:03.331: %LINK-3-UPDOWN: Interface Ethernet0/2/0, changed state to down...

  • Page 25: Configuring Auto Groups In Efm Mode

    Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Configuring Cisco G.SHDSL EFM/ATM Configuring Auto Groups in EFM Mode Use the Cisco IOS CLI on the router in global configuration mode to configure auto groups in the EFM mode. Note For EHWICs, use the three-tuple notation (slot number/subslot number/0).
  • Page 26 To troubleshoot Cisco G.SHDSL EFM/ATM, use the following new and published Cisco IOS commands. All other Cisco IOS software commands used with G.SHDSL EFM/ATM are documented in the Cisco IOS Release Release: <optional, example: Cisco IOS Release 15.1(1)T> command reference publication at Cisco.com:...
  • Page 27 Displays information about the ATM controller. show controllers atm slot/subslot number/0 Example: Router# show controllers atm 0/1/0 Examples The examples in this section show how to display the state of an EHWIC-4SHDSL-EA in a 2-wire configuration, in ATM Mode and in Mode. The commands include: ATM Mode •...
  • Page 28 Router# sh controllers shdsl 0/3/0 detailed Controller SHDSL 0/3/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 3 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...
  • Page 29 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM LoopAttn: 0dB, SnrMargin: 19dB Current 15 minute statistics (Time elapsed 556 seconds) ES:0, SES:0, CRC:0, LOSW:0, UAS:0 Previous 15 minute statistics ES:0, SES:0, CRC:0, LOSW:0, UAS:0 Current 24 hr statistics...
  • Page 30 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM rx_multicast: 1, rx_broadcast: 0 rx_mac_control: 0, rx_mac_pause: 0 rx_mac_unknown: 0, rx_err_alignment: 0 rx_err_length: 0, rx_err_code: 0 rx_false_carrier: 0, rx_undersize: 0 rx_oversize: 0, rx_fragments: 0 rx_jabber: 0, rx_dropped: 0...
  • Page 31 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM txrx_frames_1522: 0, rx_bytes: 81 rx_packets: 1, rx_err_fcs: 0 rx_multicast: 1, rx_broadcast: 0 rx_mac_control: 0, rx_mac_pause: 0 rx_mac_unknown: 0, rx_err_alignment: 0 rx_err_length: 0, rx_err_code: 0 rx_false_carrier: 0, rx_undersize: 0...
  • Page 32 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM Rx Ring Entries = 64 IRQ 1 Count DDR Tx CRC DDR Clock Miss DDR Tx Overrun MAC Tx Underrun MAC Rx Overrun MAC Large Frame MAC Rx CRC...
  • Page 33 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM MAC110 Frame statistics registers --------------------------------- Egress frame counters: ---------------------- Frame Count Byte Count Abort Count Tx64 Bytes Packet Count0 Tx65_to_127 Bytes Packet Count9 Tx128_to_255 Bytes Packet Count0...
  • Page 34 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM GDF Ring 2 Interrupt Enables: Rx Frame Drop Int Generic Frame Tx Int Generic Frame Rx Int GDF Ring 1 Interrupt Enables: Rx Frame Drop Int Generic Frame Tx Int...
  • Page 35 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM TxQueueBase 0x00 TxQueueTail 0x00 TxQueueSize 0x00 TxQueueHead 0x00 RxQueueHeadBase Register 0x0000 RxQueueBase 0x00 RxQueueHead 0x00 RxQueueSize 0x00 RxQueueTail 0x00 RxBufferSize 0x0000 RxQueueHighWaterMark 0x00 RxQueueLowWaterMark 0x00 GDF Ring 2 Registers:...
  • Page 36 Router# sh controllers shdsl 0/3/0 detailed Controller SHDSL 0/3/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 3 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...

  • Page 37: Troubleshooting Cisco G.shdsl Efm/Atm

    Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM ES:0, SES:0, CRC:0, LOSW:0, UAS:0 Current 24 hr statistics ES:0, SES:0, CRC:0, LOSW:0, UAS:0 Previous 24 hr statistics ES:0, SES:0, CRC:0, LOSW:0, UAS:0 EFM Stats: EFM-TC Tx: data fragments: 0...
  • Page 38 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM Power Back Off: 6dB LoopAttn: 0dB, SnrMargin: 18dB Current 15 minute statistics (Time elapsed 556 seconds) ES:0, SES:0, CRC:0, LOSW:0, UAS:0 Previous 15 minute statistics ES:0, SES:0, CRC:0, LOSW:0, UAS:0...
  • Page 39 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM rx_err_overrun: 0, tx_frames: 0 g999_rx_pause_frames: 0, g999_rx_errored_fragments: 0 g999_rx_length_error: 0, tx_frames: 1 tx_bytes: 77, rx_frames: 1 rx_bytes: 81, rx_dropped_frames: 0 rx_pce_denied_frames: 0 SS-SMII FA Stats at NPU:...
  • Page 40 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM show controllers ethernet Router# sh controllers ethernet 0/3/0 IOS DS Rx/Tx Counters: --------------------------: Tx Head Tx Tail Tx Count Rx Head Rx Tail IOS DS Misc counters...
  • Page 41 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM Control Register (0x8210): MAC Enable Short Packet Padding Loopback Mode TXCRC Gen Latency Register: (0xFFFE) Tx FIFO MAX Packet Count : 31 Tx FIFO MAX Byte Count : 2046...
  • Page 42 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM GDF Rx Resume Error Int Rx Done Error Int Card Present Change Int Hwic Int Frame Error Int 0x00 Tx First Last Error Int Tx Done Error Int...
  • Page 43 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM HWICQueueBaseExtension 0x00 GDF Ring 0 Registers: HWICQueueConfig Register 0x0007 HWICQueueBase 0x1DAD TXQueueTailBase Register 0x4048 TxQueueBase 0x08 TxQueueTail 0x09 TxQueueSize 0x40 TxQueueHead 0x09 RxQueueHeadBase Register 0x4800 RxQueueBase 0x09...
  • Page 44 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Troubleshooting Cisco G.SHDSL EFM/ATM DDR TXCRC Int DDR TXClk Loss Int TX Fifo Overrun Int HWIC Diag 1: 0x0 HWIC Diag 2: 0x1C05 ******* HWIC Rx/Tx Rings ******* rxr @(1DAD4800) head (0) tail (0) entries (64) serviced (0)
  • Page 45 Enable DSL Phy Training events debug <cr> Firmware Update This section describes the PHY firmware updates to the Cisco G.SHDSL multimode (ATM and EFM) EHWIC and the Cisco 888EA Integrated Services Router. System Requirements This section describes the system requirements for using SOCRATES-4e Firmware Update feature of the Cisco IOS software.
  • Page 46 Firmware Update Upgrading to a New Firmware Release You can upgrade to a new firmware release using one of the following procedures: Procedure 1 Download the new firmware from the Cisco.com Software Center at: Step 1 http://software.cisco.com/download/release.html?i=!y&mdfid=284367038&softwareid=284942912&re lease=1.7.5.0_11175002&os=UnixOrLinux. Copy the firmware to a designated location, either in the router’s flash memory or a USB flash drive’s Step 2 memory.
  • Page 47 Router# show controller shdsl 0/1/0 Controller SHDSL 0/1/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 1 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...
  • Page 48 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Firmware Update Table 1 provides a list of PHY source and firmware files. Table 1 PHY Source and Firmware Files Source PHY Source PHY Firmware Files Embedded System This section is not shown.
  • Page 49 15.3(2)T DFE: 1.1-1.7.5__002 Command Reference This section documents the following Cisco IOS commands. All other Cisco IOS software commands used with this EHWIC are documented in the Cisco IOS Release Master Command List at: http://www.cisco.com/en/US/docs/ios/mcl/allreleasemcl/all_book.html • shdsl annex shdsl rate •...
  • Page 50 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Command Reference efm-grp minimum-links • efm-grp minimum-bandwidth • handshake • shdsl 4-wire mode • mode • controller shdsl • dsl-group • show controllers shdsl • termination • Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2...
  • Page 51 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 shdsl annex shdsl annex To define a symmetric high bit rate digital subscriber line (SHDSL) G.991.2 standard, use the shdsl annex command in the configuration controller DSL group mode. shdsl annex {annex standard} [coding <tcpam>]...
  • Page 52 0/1/0 Controller SHDSL 0/1/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 1 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...
  • Page 53 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 shdsl annex Loop Attenuation alarm: none Termination: CO, Line mode: 2-wire, Annex: F Line coding: 32-TCPAM Configured/actual rate: AUTO/5696 kbps Modem status: UP_DATA_MODE,Condition: GHS_TRANSFER_ Reason: ERR_UNUSED_ Related Commands Command Description dsl-group Creates and configures a DSL group.
  • Page 54 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 shdsl rate shdsl rate To define a symmetric high bit rate digital subscriber line (SHDSL) rate, use the shdsl rate command in the configuration controller DSL group mode. shdsl rate {number | auto | enhanced}...
  • Page 55 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 shdsl rate Annex F and G (16 TC-PAM)—2304 to 3840 kbps • Annex A to F, and B to G (32 TC-PAM)—768 to 5696 kbps • Annex A to F, and B to G (16 TC-PAM)—192 to 3840 kbps •...
  • Page 56 Router# show controll shdsl 0/1/0 Controller SHDSL 0/1/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 1 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...

  • Page 57: Efm-Tc Rx: Data Frames

    Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 shdsl rate Previous 15 minute statistics ES:5, SES:5, CRC:0, LOSWS:7, UAS:0 Current 24 hr statistics ES:6, SES:6, CRC:0, LOSWS:8, UAS:0 Previous 24 hr statistics ES:0, SES:0, CRC:0, LOSWS:0, UAS:0 EFM Stats:...
  • Page 58 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 efm-grp link-stability-timer efm-grp link-stability-timer To configure the data transmission delay period for links in an Ethernet in the First Mile Bonding (EFM-Bonding) group, use the efm-grp link-stability-timer command in the configuration controller DSL group mode.
  • Page 59 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 efm-grp link-stability-timer termination cpe mode efm dsl-group 0 pairs 0, 1, 2, 3 efm-bond efm-grp link-stability-timer 13 ignore crc shdsl rate auto handshake auto Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2...
  • Page 60 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 efm-grp minimum-links efm-grp minimum-links To configure the minimum number of active links for an Ethernet in the first mile (EFM) group to be up, along with a timeout value, use the efm-grp minimum-links command in the configuration controller DSL group mode.
  • Page 61 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 efm-grp minimum-links Related Commands Command Description dsl-group Creates and configures a DSL group. Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2...
  • Page 62 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 efm-grp minimum-bandwidth efm-grp minimum-bandwidth To configure the minimum bandwidth for the active links in any digital subscriber line (DSL) group, along with a timeout value, use the efm-grp minimum-bandwidth command in the configuration controller DSL group mode.
  • Page 63 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 efm-grp minimum-bandwidth Related Commands Command Description dsl-group Creates and configures a DSL group. Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2...
  • Page 64 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 handshake handshake To configure a handshake, use the handshake command in the configuration controller DSL group mode. handshake [auto | g.shdsl | g.shdsl.bis | ieee | itut] Note The handshake command is not available in the CO-ATM mode.
  • Page 65 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 handshake In the EFM mode: • To avoid interoperability issues, use the handshake command along with the keyword that – matches the configuration that is in place during the termination at the CO.
  • Page 66 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 shdsl 4-wire mode shdsl 4-wire mode To enable the symmetric high bit rate digital subscriber line (SHDSL) to use the enhanced mode in a 2-pair digital subscriber line (DSL) group, use the shdsl 4-wire mode enhanced command in the configuration controller DSL group mode.
  • Page 67 This command was introduced to support the Cisco EHWIC-4SHDSL-EA and Cisco 888-EA ISRs. Usage Guidelines Use the ATM mode for EHWIC-4SHDSL-EA and Cisco 888-EA models, and use the EFM mode for the EHWIC-8SHDSL-E model. Examples The following example shows how to use the mode command to configure a Cisco...
  • Page 68 This command was implemented on Cisco IAD2420 series IADs. 12.4(15)T This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router, and on the Cisco 2800 and 3800 series access routers. 15.1(1)T This command was modified to support the Cisco HWIC-4SHDSL-EA.
  • Page 69 Cisco HWIC-4SHDSL, HWIC-2SHDSL, EHWIC-4SHDSL-EA, and Cisco 888EA The following example uses the controller shdsl command to configure a Cisco HWIC-4SHDSL or EHWIC-4SHDSL-EA installed in a Cisco Access Router, controller number 0, , port number 0; the example enters controller configuration mode:...
  • Page 70 To disable the DSL group, use the no form of this command. dsl-group DSL_group_number{[pairs link-number] | [auto]} {ima | m-pair | efm-bond} no dsl-group [number] Syntax Description DSL_group_nu DSL group number. Cisco 888EA and EHWIC-4SHDSL-EA support only one DSL mber group; use 0. pairs Defines the DSL wire pairs.
  • Page 71 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 dsl-group In ATM mode IMA DSL Group Available links: 0, 1, 2, 3 • Any combination of the numbers 0, 1, 2, and 3 For example: To use all available pairs , use: dsl-group 0 pairs 0-3 ima...
  • Page 72 Automatic configuration is not supported on IMA groups. Note Automatic configuration is limited to only one DSL group and ATM interface (EHWIC-4SHDSL-EA, HWIC-4SHDSL) or Ethernet interface (EHWIC-4SHDSL-EA). After a group is automatically configured, no other group can be created. All manually created groups must be deleted before creating an automatic configuration group.
  • Page 73 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 dsl-group For the HWIC-4SHDSL Router(config-controller)# dsl-group 0 pairs 0-1 ima Router(config-controller-dsl-group)# Sep 14 13:15:40.285:%HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(1) state changed to down. Sep 14 13:15:42.285:%LINK-3-UPDOWN: Interface ATM0/2/IMA1, changed state to down Sep 14 13:15:43.285:%LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/IMA1, changed...
  • Page 74 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 dsl-group Related Commands Command Description controller shdsl Configures a controller for SHDSL mode and enters configuration controller mode. ima group Defines physical links as IMA group members. ima group clock-mode Sets the clock mode for an IMA group.
  • Page 75 This command is used to display the controller mode, the controller number, and associated statistics. Examples Cisco HWIC-4SHDSL, and HWIC-2SHDSL The following example shows the status of a Cisco HWIC-4SHDSL controller in slot 0, subslot 2, port 0 on a Cisco access router: Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2...
  • Page 76 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 show controllers shdsl Router# show controllers shdsl 0/2/0 brief Controller SHDSL 0/2/0 is UP Hardware is HWIC-4SHDSL, rev 2 on slot 0, hwic slot 2 Capabilities: IMA, M-pair, 2/4 wire, Annex A, B, F & G, CPE termination cdb=0x43EB384C, plugin=0x43DE9410, ds=0x43E9A1C4 base=0xB8000000 FPGA Version is REL.3.4.0, NIOSII FW:Ver 2.6, status Running...
  • Page 77 Router#sh controller shdsl 0/3/0 Controller SHDSL 0/3/0 is UP Hardware is EHWIC-4SHDSL-EA, rev 0 on slot 0, hwic slot 3 Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G...

  • Page 78: Tx_Bytes

    Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 show controllers shdsl ATM Stats: ATM-TC Tx: data cells: 0, Idle/Unassigned: 254933993 ATM-TC Rx: data cells: 0, uncorr HEC: 14 ATM-TC Rx: OCD: 2, LCD start: 0, LCD end: 0 RMII Device Stats at NPU:...
  • Page 79 To configure the router mode to Central Office (CO) or Customer Premise Equipment (CPE), use the termination command. CO mode is useful for creating a back-to-back connection between two Cisco routers that support G.SHDSL. termination { co | cpe } Syntax Description Specifies the CO mode.
  • Page 80 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 termination Capabilities: EFM: 2-wire, EFM-Bond, Annex A, B, F & G ATM: 2-wire, Mpair, IMA, Annex A, B, F & G CO termination cdb=0x3CF085F0, plugin=0x21C33C1C, ds=0x21C33C68 base=0x10200000 FPGA Version is A14...
  • Page 81 Configuring Cisco Multimode G.SHDSL EFM/ATM in Cisco ISR G2 Additional References Additional References The following references provide links to related topics, such as the Cisco IOS software resource center, interface card documentation, and additional hardware documentation. Related Documents Related Topic...
  • Page 82 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

Table of Contents