S Control - Alto-Shaam ML Series Installation Operation & Maintenance

C O M B I T H E R M
D A I L Y O V E N C L E A N I N G
T h e C o m b i t h e r m a u t o m a t i c c l e a n i n g f u n c t i o n s e l e c t s t h e p r o p e r
t e m p e r a t u r e f o r e a c h s t e p o f t h e c l e a n i n g p r o c e s s .
1.
Remove all food scraps and residue from the oven drain.
C l o s e t h e o v e n d o o r s e c u r e l y .
R o t a t e t h e p o w e r k n o b t o t h e c l e a n i n g s y m b o l .
THE OVEN WILL BEGIN THE FIRST STEP IN A TWO-STEP CLEANING CYCLE
• 10 MINUTES at a steam temperature of 86°F (30°C)
2.
When the buzzer signals the end of the first step, o p e n t h e o v e n d o o r
t o d e a c t i v a t e t h e a u d i b l e s i g n a l . C l n w i l l a p p e a r i n t h e d i s p l a y .
3.
Wearing safety glasses and rubber gloves, remove the drain screen and spray
Combitherm liquid oven cleaner directly into the oven drain
drain screen.
4.
Generously spray the interior oven surfaces with an even coat of Combitherm
Liquid Oven Cleaner. Spray all built-in components, shelves, side racks, and pans.
5.
Loosen the thumb screw(s) and swing Fan Guard Cover Plate
the oven. Spray the back of the Fan Guard Cover Plate, the oven fan
left-hand side of the oven. Close the swing-out Cover Plate
into place and tighten thumb screw(s).
6.
Insert the Combitherm Liquid Oven Cleaner spray nozzle directly into the Steam
By-Pass Port
7.
Securely close the oven door.
THE OVEN WILL BEGIN THE SECOND STEP IN THE TWO-STEP CLEANING CYCLE
• 10 MINUTES at a steam temperature of 86°F (30°C)
8.
When the buzzer signals the end of the second step, o p e n t h e o v e n d o o r
t o d e a c t i v a t e t h e a u d i b l e s i g n a l .
9.
Use the hand held hose and direct a stream of water into the Steam By-Pass Port
to rinse away oven cleaner residue.
10.
Rinse the interior and all sprayed components with the hand-held hose. Make certain to
thoroughly rinse all surfaces to remove any cleaning solution residue. Use a non-
abrasive cleaning pad for any problem areas.
11.
Loosen the thumb screw(s) and swing Fan Guard Cover Plate toward the back of
the oven. Thoroughly rinse the back of the Fan Guard Cover Plate, the oven fan,
and the left-hand side of the oven. Close the swing out Cover Plate. Lock the
cover into place and tighten thumb screw(s).
L E A V E D O O R S L I G H T L Y O P E N A F T E R C L E A N I N G
# 6 0 0 1
C L E A N I N G & M A I N T E N A N C E
®
and spray several times.
C O M B I T H E R M E L E C T R I C I N S TA L L AT I O N A N D M A I N T E N A N C E M A N UA L
C O N T R O L
O P T I O N
. Replace the
toward the back of
, and the
. Lock the cover
. 2 3
P G