Network Settings; Wireless Lan Settings - Panasonic AG-CX350 Operating Instructions Manual

Network settings

Wireless LAN settings

This is the setting to connect with the iPad or the Android terminal directly or to connect to the wireless access point via wireless LAN.
Direct connection ([DIRECT])
This is the setting to connect the camera to the iPad/Android terminal directly.
The camera may restart if necessary when the setting is changed.
1
Select the [NETWORK] menu → [DEVICE SEL] → [WLAN].
2
Select the [NETWORK] menu → [WLAN PROPERTY] → [TYPE] → [DIRECT].
3
In the [NETWORK] menu → [WLAN PROPERTY], set each item as necessary.
f For details about the settings, refer to "Setting items in [WLAN PROPERTY] when set to [DIRECT]" (page 171).
4
Select the SSID of the camera from the SSID list in the iPad/Android terminal, and enter the password (encryption key).
Display the wireless access point list screen in wireless LAN setting, and select SSID of the camera.
f Factory setting: [AG-CX350]
When the password confirmation screen appears, enter the password (encryption key).
For details, refer to the operating instruction of the iPad/Android terminal.
f Factory setting: [01234567890123456789abcdef]
5
Close the menu or return to the level of the [NETWORK] menu.
6
Check the network connection.
Once connected, is displayed on the screen of the camera.
r Setting items in [WLAN PROPERTY] when set to [DIRECT]
[SSID]
[BAND]
[CHANNEL(2.4GHz)]
[CHANNEL(5GHz)]
[ENCRYPT KEY]
[IPv4 SETTING]
@
NOTE
t The startup time after turning on the power may be longer due to starting of the network.
t When changing the settings of [DEVICE SEL], the changes will not be reflected until the camera is restarted. Also, the setting screen termination may
take some time due to the restart of the network service after the setting is changed.
t Some of the items not included in the table cannot be set.
t [ENCRYPTION] will be fixed to [WPA2-AES].
t Depending on the used wireless module, some of the items in [BAND], [CHANNEL(2.4GHz)], and [CHANNEL(5GHz)] may not be able to select.
Connecting to the wireless access point ([INFRA(SELECT)]/[INFRA(MANUAL)])
This is the setting to connect the camera to a wireless access point.
When connecting by searching the wireless access point (SSID)
1
Select the [NETWORK] menu → [DEVICE SEL] → [WLAN].
2
Select the [NETWORK] menu → [WLAN PROPERTY] → [TYPE] → [INFRA(SELECT)].
3
In the [NETWORK] menu → [WLAN PROPERTY], set each item as necessary.
f For details about the setting items, refer to "[WLAN PROPERTY] setting items when set to [INFRA(SELECT)] or [INFRA(MANUAL)]" (page 172).
Chapter 9 Network Connection — Network settings
[DHCP]
[IP ADDRESS]
[SUBNET MASK]
Network name of the camera (SSID)
(Factory setting: [AG-CX350])
Setting to switch between two communication method ([2.4GHz] or [5GHz])
(Factory setting: [2.4GHz])
Channel to be used when [BAND] is set to [2.4GHz]
(Factory setting: [AUTO])
Channel to be used when [BAND] is set to [5GHz]
(Factory setting: [AUTO])
WPA2 encryption key
(Factory setting: [01234567890123456789abcdef])
Setting the DHCP function
f [OFF]: Does not use DHCP.
f [CLIENT]: Automatically acquired with the DHCP when connected by setting
[TYPE] to [INFRA(SELECT)] or [INFRA(MANUAL)]. (Cannot be selected.)
f [SERVER]: Enables the DHCP server function of the camera when
connecting with [TYPE] set to [DIRECT].
(Factory setting: [OFF])
IP address of the camera
(Factory setting: [192.168.0.1])
Subnet mask
(Factory setting: [255.255.255.0])
– 171 –