Panasonic AG-CX350 Operating Instructions Manual page 156

f (No display): It is in one of the following conditions.
- A memory card has not been inserted.
- The memory card cannot be recognized.
- The [NETWORK] menu → [NETWORK FUNC] → [NDI|HX] is set.
7 External equipment recording operation control status (<SDI OUT>/<HDMI> terminal)
Displays the control status of the recording start and recording stop on the external equipment connected to the <SDI OUT> terminal and the
<HDMI> terminal.
f [ S/H]: Recording instruction is output to the output from the <SDI OUT> terminal and <HDMI> terminal.
f [S/H]: Pause instruction is output to the output from the <SDI OUT> terminal and <HDMI> terminal.
f [ SDI]: Recording instruction is output to the output from the <SDI OUT> terminal.
f [SDI]: Pause instruction is output to the output from the <SDI OUT> terminal.
f [ HDMI]: Recording instruction is output to the output from the <HDMI> terminal.
f [HDMI]: Pause instruction is output to the output from the <HDMI> terminal.
8 Recording status (card slot 2)
Displays the recording status of the memory card in card slot 2.
f : Not target for recording.
f (flashing): Recognizing the memory card.
f : The recording is stopped while the recording target memory card is inserted.
f : Recording.
(Flashing red dot): Processing to stop the recording.
f
f [P ]: Recording is stopped with pre-recording is enabled and the recording target memory card is inserted.
f (No display): It is in one of the following conditions.
- A memory card has not been inserted.
- The memory card cannot be recognized.
- The [NETWORK] menu → [NETWORK FUNC] → [NDI|HX] is set.
9 Remaining recording capacity and status of the memory card (card slot 2)
Displays the remaining recording capacity and status of the memory card in card slot 2.
f [0min] to [999min]: Remaining recording capacity (999 minutes or more is displayed as [999min])
- The display will flash when the remaining recording capacity becomes two minutes or less.
- The recording capacity available for simultaneous recording (recording capacity for the memory card of the two memory cards with less recording
capacity) is displayed when simultaneous recording is performed.
f [WP]: Write protected (the write protection switch of the memory card is set to the LOCK side)
f [END]: No remaining recording capacity (no remaining recording capacity on the memory card)
f [ERR]: A memory card that cannot record is inserted (the card is recognized but cannot record due to a format error, a card other than a memory
card being inserted, etc.)
f [!SDXC]: The SDXC memory card is not inserted for MOV recording
f (No display): It is in one of the following conditions.
- A memory card has not been inserted.
- The memory card cannot be recognized.
- The [NETWORK] menu → [NETWORK FUNC] → [NDI|HX] is set.
10 Special recording function
Displays the status of special recording function.
f [INTRVL]: The interval recording is stopped.
f [I-REC]: The interval recording is in progress. (Displayed in red)
11 Two-slot function
Displays the setting status of the recording function using two memory cards.
It is displayed with a slanted line if it is in a condition that cannot perform two-slot recording even if each function is enabled.
f [RELAY]: When the relay recording is enabled
f [SIMUL]: When the simultaneous recording is enabled
f [BACKGR]: When the background recording is enabled
f (No display): During standard recording (when set to the [NETWORK] menu → [NETWORK FUNC] → [NDI|HX], [NDI|HX] is displayed)
12 Flash band compensation function
f [FBC]: Displayed when the flash band compensation function is operating.
13 Streaming status
Displays the streaming status.
f : When the camera is connected to a device to receive the streaming video, and the streaming video is distributed
f (flashing): When the camera is being connected to a device to receive the streaming video
f : When the streaming function is enabled, it is in condition to operate properly, and the streaming video is not distributed
f : When there is an error in the streaming function and cannot operate
f (No display): When the streaming function is disabled
14 High dynamic range recording function/dynamic range stretcher function
f [HDR]: When set to the [SCENE FILE] menu → [GAMMA MODE SEL] → [HLG]
f [DRS]: When the dynamic range stretcher function is operating
15 Connection status of the wireless LAN/wired LAN
Displays the connection status of the wireless LAN or wired LAN.
: When set to the wireless LAN and the ROP is not connected
f
f : When set to the wireless LAN and the ROP is connected
Chapter 7 Output and Screen Display — Screen status display
– 156 –