Siemens SINAMICS G120C Compact Operating Instructions page 62

Commissioning
4.2 Commissioning with BOP-2 operator panel
No. Description
p0845 BI: No coast down/coast down (OFF2) signal
source 2
p0848 BI: No quick stop/quick stop (OFF3) signal source
1
p0849 BI: No quick stop/quick stop (OFF3) signal source
1
p0852 BI: Enable operation
p0854 BI: Master control by PLC
p0855 BI: Unconditionally release holding brake
p0856 BI: Enable speed controller
p0857 Power Module monitoring time [ms]
p0858 BI: Unconditionally close holding brake
p0860 BI: Line contactor, feedback signal
p0861 Line contactor, monitoring time [ms]
r0863 CO/BO: Drive coupling status word / control word
.00 1 = closed-loop
control, operation
p0867 Power unit main contactor hold time after OFF1
[ms]
p0869 Configuration sequence control
.00 1 = keep main contactor closed for STO
r0898 CO/BO: Control word sequence control
r0899 CO/BO: Status word sequence control
p0922 PROFIdrive telegram selection
1 Standard telegram 1, PZD-2/2
20 Standard telegram 20, PZD-2/6
352 SIEMENS telegram 352, PZD-6/6
353 SIEMENS telegram 353, PZD-2/2, PKW-
4/4
354 SIEMENS telegram 354, PZD-6/6, PKW-
4/4
999 Free telegram configuration with BICO
r0944 CO: Counter for fault buffer changes
r0945 Fault code
r0946 Fault code list
r0947 Fault number
r0948 Fault time received in milliseconds [ms]
r0949 Fault value
p0952 Fault cases, counter
r0964 Device identification
62
.01 1 = operate line
contactor
Compact Operating Instructions, 11/2016, FW V4.7 SP6, A5E39339884B AA
No. Description
p0965 PROFIdrive profile number
p0969 System runtime relative [ms]
p0970 Reset drive parameters
0 Inactive
5 Reset safety pa-
rameters
11 Load setting 11
100 Reset BICO interconnections
p0971 Save parameters
0 Inactive
1 Save in nonvolatile storage (RAM → ROM)
10 Save in a non-volatile memory as setting 10
11 Save in a non-volatile memory as setting 11
12 Save in a non-volatile memory as setting 12
p0972 Drive unit reset
p1000 Speed setpoint selection
p1001 CO: Fixed speed setpoint 1 [rpm]
p1002 CO: Fixed speed setpoint 2 [rpm]
... ...
p1015 CO: Fixed speed setpoint 15 [rpm]
p1016 Fixed speed setpoint mode
1 Direct selection
p1020 BI: Fixed speed setpoint selection bit 0
p1021 BI: Fixed speed setpoint selection bit 1
p1022 BI: Fixed speed setpoint selection bit 2
p1023 BI: Fixed speed setpoint selection bit 3
r1024 CO: Fixed speed setpoint effective [100 % ≙
p2000]
r1025 BO: Fixed speed setpoint status
.00 Fixed speed setpoint selected
p1030 Motorized potentiometer configuration
00 Storage active
01 Automatic operation, ramp-function genera-
tor active
02 Initial rounding active
03 Storage in NVRAM active
p1035 BI: Motorized potentiometer setpoint raise
SINAMICS G120C, FSD ... FSF inverters
1 Reset parameters
except for Safety
10 Load setting 10
12 Load setting 12
2 Selection, binary
coded