Magnetek Elevator HPV1000 AC Technical Manual page 26

5 Programming
C3 Parameter Name
Logic output P1
Logic output P2
Relay M1-M2
Relay M3-M4
Relay M5-M6
C3 Choice
Auto Brake Output (uses encoder feedback to
Auto Brake
ensure motor is stationary before setting)
BaseBlock NO Base Block output Normally Open
BaseBlock NC Base Block output Normally Closed
Brake Pick Output (uses run signaling/timers to set
Brake Pick
the brake)
Close Contact Motor Contactor output
DBR Trans Flt Dynamic Braking Transistor Fault
DC Bus Undervolt DC Bus Undervolt Fault
Door Zone Door Zone Output
Drive Ready Drive Ready to Run
Dur Flt Restart Drive fault being reset
During Run 1 Output closes when the drive is outputting a voltage
Output closes when the drive is outputting a
During Run 2
frequency
Fan Alarm Internal cooling fan alarm
Fault Drive in a faulted state
Input Ph Loss Input Phase Loss detected
LightLoadDetStat Light Load Direction Detection Status
LightLoadDirect Light Load Direction
Maintenance Drive requires maintenance
Minor Fault A Minor fault is active
Motor Overload Motor Overload fault active
Not Used Output not used
Overheat Alarm Motor or drive over temperature alarm active
Ovld Shdwn Alm Overload shutdown alarm active
Regenerating ,
<3>
Drive is running and regenerating (not motoring)
<4>
Reset Cmd Active Fault Reset input active
Reverse Dir Lift traveling in reverse direction (down)
SafeDisable Stat Safe Disable Status
Spd Detection 3 Speed Detection 3
Spd Detection 4 Speed Detection 4
Spd Ref Release Speed Reference Release active
Spd Reg Release Speed Regulator Release active
SRef/Out Agr 1 Speed Reference Agree 1
SRef/Out Agr 2 Speed Reference Agree 2
SRef/Set Agr 1 Speed User Set Agree 1
SRef/Set Agr 2 Speed User Set Agree 2
Speed Dev Low
Speed Deviation low active
,
<3> <4>
Torque Detect 1 Torque Detect 1
Torque Detect 2 Torque Detect 2
Torque Limit
Drive in Torque Limit
, ,
<2> <3> <4>
Zero Speed Zero speed output
! BaseBlock NC Base Block output Normally Open (Inverse)
24
Table 9 C3 Logic Outputs
Terminal P1 - C1 Function Selection (photocoupler)
Terminal P2 - C2 Function Selection (photocoupler)
Terminal M1 - M2 Function Selection (relay)
Terminal M3 - M4 Function Selection (relay)
Terminal M5 - M6 Function Selection (relay)
Table 10 Logic Output Choices
Description
Description
C3 Choice
! BaseBlock NO Base Block output Normally Closed (Inverse)
Brake Pick Output (uses run signaling/timers to set
! Brake Pick
the brake) (Inverse)
! Close Contact Motor Contactor output (Inverse)
! Drive Ready Drive Ready to Run (Inverse)
! DBR Trans Flt Dynamic Braking Transistor Fault (Inverse)
! DCBus Undervlt DC Bus Undervolt Fault (Inverse)
! Door Zone Door Zone Output (Inverse)
Output closes when the drive is outputting a
! During Run 1
voltage (Inverse)
Output closes when the drive is outputting a
! During Run 2
frequency (Inverse)
! Fan Alarm Internal cooling fan alarm (Inverse)
! Fault Drive in a faulted state (Inverse)
! Input PH Loss Input Phase Loss detected (Inverse)
! LiteLoadDetSta Light Load Direction Detection Status (Inverse)
! LiteLoadDirect Light Load Direction (Inverse)
! Maintenance Drive requires maintenance (Inverse)
! Minor Fault A Minor fault is active (Inverse)
! Motor Overload Motor Overload fault active (Inverse)
Motor or drive over temperature alarm active
! Overheat Alarm
(Inverse)
! Ovld Shdwn Alm Overload shutdown alarm active (Inverse)
! Regenerating
Drive is running and regenerating (Inverse)
,
<3> <4>
! ResetCmd Activ Fault Reset input active (Inverse)
! Restart Enable Output active unless drive fault auto reset occurring
! Reverse Dir Lift traveling in reverse direction (down) (Inverse)
! SafeDisablStat Safe Disable Status
! Spd Ref Rls Speed Reference Release active (Inverse)
! Spd Reg Rls Speed Regulator Release active (Inverse)
! Speed Dev Low
Speed Deviation low active (Inverse)
,
<3> <4>
! SRef/Out Agr 1 Speed Reference Agree 1 (Inverse)
! SRef/Out Agr 2 Speed Reference Agree 2 (Inverse)
! SRef/Set Agr 1 Speed User Set Agree 1 (Inverse)
! SRef/Set Agr 2 Speed User Set Agree 2 (Inverse)
! Torque Limit
Drive in Torque Limit (Inverse)
, ,
<2> <3> <4>
! Trq Det 1 N.O. Torque Detect 1 (Inverse)
! Trq Det 2 N.O. Torque Detect 2 (Inverse)
! Zero Speed Zero speed output (Inverse)
<2> Parameter accessible in Open Loop Vector control mode
<3> Parameter accessible in Closed Loop Vector control mode
<4> Parameter accessible in PM Closed Loop Vector control mode
<5> Default is dependent on drive model number
MAGNETEK HPV1000 AC Elevator Drive Technical Manual
Default
Not Used
Not Used
Not Used
Not Used
Not Used
Description