Magnetek Elevator HPV1000 AC Technical Manual page 25

C2 Parameter Name
Logic Input S1
Logic Input S2
Logic Input S3
Logic Input S4
Logic Input S5
Logic Input S6
Logic Input S7
Logic Input S8
C2 Parameter
Choice
Brake Feedback NC Brake Feedback Normally Closed
Brake Feedback NO Brake Feedback Normally Open
Comm Test Mode Serial Comm Test Mode
Contact Cnfm NC Contactor Confirmation Normally Closed
Contact Cnfm NO Contactor Confirmation Normally Open
DL Dist Correctn Stop Distance Correction Input
Drive Enable Drive Enable
BaseBlock NC Base Block Normally Closed
BaseBlock NO Base Block Normally Closed
Fast-Stop NO Fast Stop Normally Open
Fast-Stop NC Fast Stop Normally Closed
Fault Reset Fault Reset
Insp Operation Inspection Operation
Intermed Speed Intermediate Speed
Jog Freq Ref Jog Frequency Reference
Leveling Speed Leveling Speed
Mains Dip Enable Mains Dip Enable
Multi-Step Ref 1 Multi-Step input 1
Multi-Step Ref 2 Multi-Step input 2
Multi-Step Ref 3 Multi-Step input 3
Multi-Step Ref 4 Multi-Step input 4
Normally Closed External Fault (always detect,
NC Ext Fault 1
ramp to stop)
Normally Closed External Fault (always detect,
NC Ext Fault 2
cost to stop)
Normally Closed External Fault (always detect,
NC Ext Fault 3
fast stop)
Normally Closed External Fault (always detect,
NC Ext Fault 4
alarm only)
Normally Closed External Fault (during run,
NC Ext Fault 5
ramp to stop)
Normally Closed External Fault (during run,
NC Ext Fault 6
cost to stop)
Normally Closed External Fault (during run, fast
NC Ext Fault 7
stop)
MAGNETEK HPV1000 AC Elevator Drive Technical Manual
Table 7 Logic Inputs C2 Submenu
Logic Input 1 on terminal S1
Logic Input 2 on terminal S2
Logic Input 3 on terminal S3
Logic Input 4 on terminal S4
Logic Input 5 on terminal S5
Logic Input 6 on terminal S6
Logic Input 7 on terminal S7
Logic Input 8 on terminal S8
Table 8 Logic Input Choices
Description
Description
C2 Parameter
Choice
Normally Closed External Fault (during run,
NC Ext Fault 8
alarm only)
Normally Open External Fault (always detect,
NO Ext Fault 1
ramp to stop)
Normally Open External Fault (always detect,
NO Ext Fault 2
cost to stop)
Normally Open External Fault (always detect,
NO Ext Fault 3
fast stop)
Normally Open External Fault (always detect,
NO Ext Fault 4
alarm only)
Normally Open External Fault (during run, ramp
NO Ext Fault 5
to stop)
Normally Open External Fault (during run, cost
NO Ext Fault 6
to stop)
Normally Open External Fault (during run, fast
NO Ext Fault 7
stop)
Normally Open External Fault (during run,
NO Ext Fault 8
alarm only)
Nominal Speed Nominal Speed Input
Not Used Input Not Used
Pre-Torque Latch Pre-Torque Latch Input
Re-Lvling Speed Re-Leveling Speed Input
Rescue Operation Rescue Operation Input
Run Down Run Down Input
Run Up Run Up Input
Run Run Input
S-curve Select 0 S-curve Select 0 Input
S-curve Select 1 S-curve Select 1 Input
Ser2 Insp Ena Ser2 Insp Enable Input
Speed Limit Down Speed Limit Down
Speed Limit Up Speed Limit Up
Timer function Timer function
Up/Down Up/Down Input
5 Programming
Default
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Not Used
Description
23