Magnetek Elevator HPV1000 AC Technical Manual page 18

5 Programming
A1 Parameter Name
Spd Dev Low Lvl ,
<3> <4>
Spd Dev Low Time ,
<3> <4>
Speed Dev Alm Lvl ,
<3> <4>
Spd Dev Alm Time ,
<3> <4>
Spd Dev Flt Lvl ,
<3> <4>
Spd Dev Flt Time ,
<3> <4>
PreTrq Time ,
<3> <4>
PreTrq Dec Freq ,
<3> <4>
PreTrq Dec Time ,
<3> <4>
Slip Comp Gain M ,
<1> <2>
Slip Comp Gain R ,
<1> <2>
Trq Det Dly Time ,
<1> <2>
Trq Det FltrTime ,
<1> <2>
Slip Comp Gain ,
<2> <3>
Slip Comp Time
<2>
Slip Comp Limit
<2>
Torq Comp Gain ,
<1> <2>
Torq Comp Time ,
<1> <2>
Zero Speed Level
Zero Speed Width
SpdAgreeLvl +/-
SpdAgreeWdth +/-
Run Delay Time
16
Description
When the difference between the speed reference and the speed
feedback value exceeds this setting for the time set in Dev Low Time
(A1), the Speed Deviation Low digital output is open.
Setting of 0.0 disables this feature (aka. output will always be closed).
When the difference between the speed reference and the speed
feedback value exceeds the level in Dev Low Level (A1) for this time
setting, the Speed Deviation Low digital output will open.
When the difference between the speed reference and the speed
feedback value exceeds this setting for the time set in Alarm Time
(A1), a Speed Dev alarm is generated.
A setting of 0.0 disables this feature.
Defines the time the Speed Feedback (D1) signals needs to be in the
range of Speed Reference (D1) before a Speed Dev alarm is declared.
The range is defined by Spd Dev Alm Lvl (A1).
When the difference between the speed reference and the speed
feedback value exceeds this setting for the time set in Fault Time
(A1), a Speed Dev fault is generated.
A setting of 0.0 disables this feature.
Defines the time the Speed Feedback (D1) signals needs to be in the
range of Speed Reference (D1) before a Speed Dev Fault is declared.
The range is defined by Spd Dev Flt Lvl (A1).
Sets a time constant for the torque reference to reach 300%. Enabled
by setting an analog terminal for torque compensation.
Effective only when Trq Comp Type (C1) is set to Pre-torque.
Sets the speed level for torque compensation to diminish.
A setting of 0.0 disables this function.
Effective only when Trq Comp Type (C1) is set to Pre-torque.
Sets the time for torque compensation to diminish once motor speed
reaches the level set in TrqCmpFadeoutSpd (A1).
Effective only when Trq Comp Type (C1) is set to Pre-torque.
Slip compensation for leveling speed in the motoring region.
Slip compensation for leveling speed in the regenerative region.
Sets a delay time before detecting torque for slip compensation.
Sets the filter time constant applied to the torque signal used for the
slip compensation value calculation.
Sets the gain for the motor slip compensation function.
Adjusts the slip compensation function delay time.
Sets an upper limit for the slip compensation function as a percentage
of motor rated slip.
Sets the gain for the automatic torque (voltage) compensation
function and helps to produce better starting torque.
Sets the torque compensation filter time.
Sets the detection level for Zero Speed output.
Sets the width for Zero Speed output.
Sets the speed detection level for digital output functions SpdRef /Out
Agr (C3), SpdRef /Set Agr (C3), Spd Detection 3 (C3), and Spd
Detection 4 (C3).
Sets the range of the speed detection for digital outputs SpdRef /Out
Agr (C3), SpdRef /Set Agr (C3), Spd Detection 3 (C3), and Spd
Detection 4 (C3).
Sets the time that must pass after the Up/Down command is entered
until the drive internal Run command is set and the ride is started.
Units
% ,
<3> <4>
Sec ,
<3> <4>
% ,
<3> <4>
Sec ,
<3> <4>
% ,
<3> <4>
Sec ,
<3> <4>
ms ,
<3> <4>
Hz ,
<3> <4>
ms ,
<3> <4>
-
-
ms ,
<1> <2>
ms ,
<1> <2>
-
ms
<2>
%
<2>
-
ms ,
<1> <2>
%
%
%
%
Sec
MAGNETEK HPV1000 AC Elevator Drive Technical Manual
Default
10.0 ,
<3> <4>
0.50 ,
<3> <4>
15.0 ,
<3> <4>
00.10 ,
<3> <4>
25.0 ,
<3> <4>
00.50 ,
<3> <4>
500 ,
<3> <4>
0.0 ,
<3> <4>
1000 ,
<3> <4>
0.7 ,
<1> <2>
1.0 ,
<1> <2>
1000 ,
<1> <2>
500 ,
<1> <2>
1.0 ,
<2> <3>
2000
<2>
200
<2>
1.00 ,
<1> <2>
200
<1>
50
<2>
80.0
4.0
0.0
4.0
0.00