Table of Contents Table of Contents Safety..........................5 Explanations of symbols ..................5 Demands on the operator and technicians............5 Intended use ......................6 Changes and modifications ................6 Operational safety and special dangers ............7 Information on the operating and installation manual ..........8 Identification ........................9 Nameplate......................9 Technical Data:........................9 Design and function......................10...
Page 4
7.1.4 Adjust display contrast (only for FCU4xxx)........... 27 7.1.5 Light settings (only for menu "Pro") ............27 „Basic settings“ for Options................29 7.2.1 Colour light automatic ................29 7.2.2 RGB-LED settings (only for FCU4xxx and menu "Pro") ....... 29 7.2.3 Colour light automatic (only for menu "Pro") ........
Safety Safety Explanations of symbols Warnings Warnings in this operating manual are indicated through symbols. The instructions are introduced through signal words, which express the degree of danger. Follow these instructions strictly and take care to avoid accidents, personal injuries and property damage.
Safety ance. Cleaning and user maintenance shall not be made by children without supervi- sion. The operating instructions are to be read carefully before switching on the unit! To en- sure safe operation and safe working practices you must comply with all the given safety and handling instructions.
Safety Operational safety and special dangers Pay attention to the safety and warning notes in the following chapters of this manual to minimize health hazards and to avoid dangerous situations. The following instructions are to be adhered to for your own safety and the safety of the unit: Electric poten- DANGER!
Safety Information on the operating and installation manual An operating manual as well as an installation manual are available for the FASEL con- trol unit. The operating manual is meant for the user and gives important instructions for handling the FASEL control unit. The installation manual describes the assembly, installation, commissioning, rectifica- tion of defects and repair and is provided exclusively for the technical personnel.
Identification Identification Nameplate The nameplate is located on the control unit on the left side: Art Nr Spg.: RoHS Geräte Nr.: conform Fig.1 Control unit nameplate Type designation Company logo Article number Voltage and max. power Device number Barcode article number Barcode article number VDE mark (for devices that are approved by VDE) RoHS marking...
Design and function Design and function Function Die the control unit is suitable for the following mode: Infrared 4.1.1 Infrared In the "Infrared" mode, an infrared heater (infrared lamp or heating surfaces) produces an IR-radiation. This heats the air in the cabin. As long as the infrared heater heats up, the status LED shows "IR"...
Design and function Operating and display elements 4.2.1 FCU2000/3000/4000-IR-Design "IR-heater" symbol "Set temperature" symbol "Set heating time / remaining heating time " "IR" key "Timer" symbol Display Control unit ON (only design) key "light" Control unit OFF (only design) key " fan" key "basic settings""...
Design and function 4.2.2 Control keys infrared control The Infrared control is equipped with the following control keys: Description "Infrared mode" key Depending on the status of the green lamp, the "Infrared mode" key has different func- tions. Status lamp next to the key Meaning Does not light up Mode is not selected.
Page 13
Design and function Description Change mode ON: (the green lamp next to navigation keys lights up): Move cursor to the left. Change mode OFF: (the green lamp next to navigation keys does not light up): Go back to the parent menu. Change mode ON: (the green lamp next to navigation keys lights up): Move cursor to the right.
Design and function Display symbols The following symbols can appear in the display: Display elements Description Selection checkmark 0 / 1 Enter Table: 3 Display symbols FCU2/3000-IR Display elements Description Temperature Heating time Remaining heating time ...
Operation Operation Safety and instructions Electric DANGER! potential Danger to life due to electric potential! Touching live parts can cause immediate danger to life. Therefore: – Control unit should be opened only by authorised electricians. – Electrical work on the machine should be carried out only by qualified electricians.
Operation NOTE! The temperature values displayed on the control unit may vary from that displayed on the thermometers mounted additionally in the cabin. This may be because of the following reasons: Depending on the cabin, temperatures differences of up to 40K can oc- cur from the floor to ceiling.
“General settings” menu “General settings” menu 6.1.1 Select or start the mode Mode Turn on Infrared control according to chapter 5.2.1. select or start The green lamp flashes. Press the key for Infrared mode. The desired mode has been started only when the green lamp stops flashing.
“General settings” menu Adjust the set point temperature, heating time, remaining heating time, timer The following example describes how to adjust the set point temperature. The heating time, the remaining heating time and the timer are adjusted similarly. Note the following points: If you want to adjust the set point temperature, set point humidity, heating time, re- maining heating time or the timer, the corresponding symbol must light up at the right of the display.
“General settings” menu Press -key. The last digit flashes. Select desired value: Press -key to reduce value. Press -key to increase value. Note! After the digit „9“ or „0“ the higher digit of the temperature value is changed. That is: “40”...
“General settings” menu The control devices are delivered with a maximum adjustable heating time of 6 hours. If you need heating times exceeding 6 hours, please contact the installer or the dealer of your sauna system. Menu for Options 6.4.1 RGB-LED brightness (only for FCU4xxx and menu "Pro") NOTE! The "RGB-LED brightness"...
Page 21
“General settings” menu Parameter Description OFF / ON OFF: The colour light mode is off. ON: The colour light mode is on. The colour lights are controlled either directly (manual) or by an automatic program (auto). Manual / Auto The option "ON" must be selected. Manual: The colour lights are manually controlled us- ing this "Colour light mode".
Page 22
“General settings” menu Fig. 5: View "Set colour light – change mode" (example) Select one of the following lines with the key: – OFF / ON (→ point 7) –...
“General settings” menu Key: Select colour program no. 2. – "2" is displayed for "colour program no.” Key: Select colour program no. 1. Key: without function 14. Press the key. The selection is saved. 15. Exit the menu using the key or select the next line with the key.
Page 24
“General settings” menu Fig. 6: View "colour light start" Press key or -key. Following view is displayed: Fig. 7: View "Set colour light start – change mode" (example) Select one of the following lines with the key: ...
„Basic settings“ menu „Basic settings“ menu For using the menu „basic settings“ please press the key (basic settings). The lamp next to the key must light. General basic settings 7.1.1 Time and Weekday In this menu you can set the time and the weekday. Press key (basic settings).
„Basic settings“ menu Exit the menu by using the -key or select the next line with the -key. 10. Select desired weekday. Check mark flashes. Press -key: move cursor left. Press -key: move cursor right. 11. Press -key. Selection is saved. 12.
„Basic settings“ menu Fig. 11: "Display lighting" view (example) Press the key. Value flashes. Adjust the desired value: Press the key: Reduce value. Press the key: Increase value. 0: dark 9: bright Press the key.
Page 28
„Basic settings“ menu Press (basic settings) key. The lamp next to the key must light up. Press the key until you see the following view: Fig. 13: “Light settings" view (example) Press the key.
„Basic settings“ menu 12. Press the key. The selection is saved. 13. Exit the menu using the key or select the next line with the key. 14. Press the key. The selected line is enabled. 15. Adjust the time for turn off delay. Digit flashes. Press the key: Reduce value.
Page 30
„Basic settings“ menu Not available with FCU2000 and FCU3000! Fig. 15: "RGB-LED settings" view Press the key. Following view is displayed: Not available with FCU2000 and FCU3000! ...
„Basic settings“ menu 7.2.3 Colour light automatic (only for menu "Pro") Note! The "Colour light automatic" menu is only available for control devices with the extension board type FCU-EXT-COLOR LIGHT or a RGB-LED control from the company Licht2000. In this menu you can program the sequence, if you have selected the "Auto" option in the "Colour light mode".
„Basic settings“ menu Select colour program no. Cursor flashes on the selected line. Press the key. Increase value. Press the key: Reduce value. Press the key. The selection is saved. Exit the menu using the key or select the next line with the key.
Page 33
„Basic settings“ menu Fig. 19: View "Versions and data" Press the key. The following view is shown: Fig. 20: View "HW- and SW-versions" (example) With the keys you can navigate within the menu. The following information is displayed here: –...
Options menu Options menu Small/professional The control unit offers two menu navigations "small" and "professional". The menu "small" includes the main menu items. The menu "professional" includes all menu items. Typically, the menu navigation "small" is sufficient. You can change the menu as follows: Press the key.
Maintenance Maintenance The infrared controls are maintenance free. Cleaning Aggressive PLEASE NOTE! cleaning agents Device damage possible! Aggressive cleaning agents and additives can damage or destroy the additives electrical components and cable. Therefore: – Do not use cleaning agents and additives with aggressive substan- ces.
Malfunctions 10.2 Malfunction messages Possible malfunctions and troubleshooting measures are described in this chapter. Contact the installer or the dealer of your sauna systems for malfunctions that are not described below. See the invoice, delivery note or the reverse of this manual for the address.
Decommissioning and disposal 10.3 Acknowledge malfunction message Rectify the cause of the message. -Press the key for about 2 seconds. Message disappears. 11 Decommissioning and disposal Do not dispose the sauna control with household waste. Dispose the control unit according to the respective country-specific regulations. B_FCUxxxx-IR / Version V 1.07 Series FCU2000/3000/4000-IR...
General Information 12 General Information 12.1 Liability limitation All the details and instructions in this manual have been compiled taking into considera- tion the relevant standard specifications and stipulations and the state-of-the-art tech- nology as well as our knowledge and experience of many years. The manufacturer does not take any liability for damages caused by: Non-compliance to the operating and installation manual Improper use...
General Information 12.4 Spare parts CAUTION Danger of injury due to incorrect spare parts Incorrect or defective spare parts could lead to damage, incorrect func- tioning or total breakdown and can impair the safety. Therefore: – Use only original spare parts of the manufacturer. –...
Setting values 13 Setting values 13.1 Range of Adjustment Infrared min. max. Temperature 30° C 90 ° C(45° C**) Operating time 00:15 h 02:00 h (20:00 h *) We deliver the control units with a max. heating time of 2 hours. If you need a •...