For Devices With 7 Mm Connectors; For Devices With Waveguide - Keysight PNA-X Series Configuration Manual

For devices with 7 mm connectors

Mechanical calibration kits
85050B standard: DC to 18 GHz. Includes:
– 00909-60008 7 mm coax termination
– 85050-60006 7 mm fixed broadband load
– 85050-80007 7 mm short
– 85050-80010 7 mm open
– 85050-80011 7 mm sliding load
85050C precision TRL: DC to 18 GHz. Includes:
– 00909-60008 7 mm coax termination
– 85050-60003 7 mm to 7 mm airline
– 85050-60005 7 mm to 7 mm TRL adapter
– 85050-60006 7 mm fixed broadband load
– 85050-80008 7 mm short
– 85050-80009 7 mm short collet
– 85050-80010 7 mm open
85050D economy: DC to 18 GHz. Includes:
– 85050-60006 7 mm fixed broadband load
– 85050-80007 7 mm short
– 85050-80010 7 mm open
Electronic calibration kits
N4696B Microwave ECal: 300 kHz to 18 GHz, 2-ports, 7 mm
connectors
Option 150: Replaces standard storage container with a wooden
box
N4696D 1 Microwave ECal: DC or 300 kHz to 18 GHz, 2-ports,
7 mm connectors. Includes:
– Option 0DC: DC to 18 GHz
– Option 003: 300 kHz to 18 GHz
Cables
– 85132E single, flexible: 3.5 mm (f) to 7 mm, 97.2 cm,
38.25 inches
2
– 85132F set, flexible: two 3.5 mm (f) to 7 mm cables, 62.9 cm
each, 24.75 inches each
– 85133F cable set (set, flexible, 2.4 mm, 53 cm each,
21 inches each)
– 85134F cable set (set, flexible, 2.4 mm (f) to 3.5 mm (f) and
(m), 53 cm each, 21 inches each)
– 85135E single, flexible: 2.4 mm (f) to 7 mm, 96 cm, 38 inches
– 85135F set, flexible: two 2.4 mm (f) to 7 mm cables, 53 cm
each, 21 inches each, p/n 85135-60002
1. The PNA Series must have firmware revision A.12.85.00 or above for the
operation with the N469xD Series ECal.
2. Special rugged female connector specifically for connecting to the
network analyzer test port, but does not mate with a standard male
connector.
Find us at www.keysight.com
, p/n 85132-60004
2
Adapter sets
– 85130E 2.4 mm to 7 mm
– R281A adapter (2.4 mm (f) to WR-28 waveguide adapter)
– R281B adapter (2.4 mm (m) to WR-28 waveguide adapter)
– Q281A adapter (2.4 mm (f) to WR-22 waveguide adapter)
– Q281B adapter (2.4 mm (m) to WR-22 waveguide adapter)

For devices with waveguide

Mechanical calibration kits
X Band
X11644A standard, WR-90: 8.2 to 12.4 GHz. Includes:
– 00896-60008 X-band standard section
– 00910-60003 X-band termination
– 11644-20018 X-band short
– 11644-20021 X-band shim
– X281C adapter (included in calibration kit): WR-90 to 7 mm
P Band
P11644A standard, WR-62: 12.4 to 18 GHz. Includes:
– 00896-60007 P-band standard section
– 00910-60002 P-band termination
– 11644-20017 P-band short
– 11644-20020 P-band shim
– P281C adapter (included in calibration kit): WR-62 to 7 mm
K Band
– K11644A standard, WR-42: 18 to 26.5 GHz. Includes:
– 00896-60006 K-band standard section
– 00910-60001 K-band termination
– 11644-20016 K-band short
– 11644-20019 K-band shim
– K281C adapter (included in calibration kit): WR-42 to 3.5 mm
(f) Option 012 WR-42 to 3.5 mm (m)
R Band
R11644A standard, WR-28: 26.5 to 40 GHz. Includes:
– 00914-20028 R-band termination
– 11644-20005 R-band short
– 11644-20003 R-band shim
– 11644-60001 R-band 10 cm straight waveguide
– 11644-60016 R-band 5 cm straight waveguide
Page 45