5/ Jumpers And Connectors; Table 3: Jumpers And Connectors Of Q7Eval - Kontron Qseven-Eval Carrier User Manual

5/ Jumpers and Connectors

This chapter gives the definitions and shows the positions of jumpers, headers and connectors. All of the
configuration jumpers on the board are in the proper positionHardware Configuration Setting
In general, jumpers on the board are used to select options for certain features. Some of the jumpers are designed to
be user-configurable, allowing for system enhancement. The others are for testing purpose only and should not be
altered. To select any option, cover the jumper cap over (SHORT) or remove (NC) it from the jumper pins according to
the following instructions. Here, NC stands for "Not Connect".

Table 3: Jumpers and Connectors of Q7EVAL

Connector
Module Power-in Connector
(J64)
5 V/3.3 V (J24)
5 V/12 V (J25)
Dual DisplayPort/HDMI (J27)
DP/LVDS (J26)
MPCIE_0_W_DISABLE1# (J5)
MPCIE_0_W_DISABLE2# (J6)
MPCIE_1_W_DISABLE1# (J7)
MPCIE_1_W_DISABLE2# (J8)
CODEC_OPTION_SW_I2S_HD
A# (J35)
microSD Write Protect (J9)
CAN Bus Termination (J10)
GPIO/LPC (J11)
CPU Fan 12V/5V (J30)
System Fan 12V/5V (J29)
System Fan PWM control
(J18)
Boot Selection (J14)
ATX PSU control (J28)
ATX PSU force (J17)
LEDs ENABLE (J19)
V_BAT_JP (J31)
COM(RS232) (J58)
USB 3.0 (J34)
microUSB 2.0 OTG (J22)
QSEVEN (J1)
CAN (J57)
Gigabit Ethernet (J33)
LVDS (J23)
www.kontron.com
Function
Module power-in selection from 3 V to 5.25 V.
ATTENTION: J64 powers the module ONLY! Carrier still
needs to be powered via 12V, through (J21) Power-In
connector or (J20) ATX Connector.
Display voltage selection (3.3 V/5 V)
Display backlight voltage selection (5 V/12 V)
Graphic Display selection (DP or DD0 in current)
Graphic Display selection (LVDS/DP)
Disable miniPCIe radio operation
Disable miniPCIe radio operation
Disable miniPCIe radio operation
Disable miniPCIe radio operation
Audio Codec Multipexor HDA/I2S Codec
microSD Write Protect Disable/Enable
CAN Bus Termination Enable/Disable
GPIO/LPC to Header
CPU Fan 12V/5V
Sys Fan 12V/5V
System Fan without/with PWM control
Boot from Module/Carrier SPI Flash
Control by SUS_S3#/SUS_S5#
ATX PSU is controlled by module/Force ATX PSU to ON
Enable/Disable status and power LEDs
Selection between Battery or Goldcap
Serial connector from QSEVEN module
Dual Stacked USB 3.0 connectors
microUSB 2.0 connector
QSEVEN connector
CAN, Molex 53261-0471 or similar
GBE connector
LVDS dual channel from QSEVEN module. Configurable
3.3 V / 5 V voltage levels of power for different panels
QSEVEN-Eval Carrier - Rev. 1.1
Remark
1x4-pin Connector
1x3-pin Jumper
1x3-pin Jumper
1x3-pin Jumper
1x3-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x3-pin Jumper
1x3-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x3-pin Jumper
1x2-pin Jumper
1x2-pin Jumper
1x3-pin Jumper
standard
standard
standard
1x230-pin header
1x4 header
standard
1x30 pins
// 23