Section 10 Replaceable Mechanical Parts - Tektronix 2215A Instruction Manual

PA R TS O R D E R IN G IN F O R M A T IO N
Replacement parts are available from or through your local
Tektronix, Inc. Field Office or representative
Changes to Tektronix instruments are sometimes made to
accommodate improved components as they become available,
and to give you the benefit of the latest circuit improvements
developed in our engineering department. It is therefore
important, when ordering parts, to include the following
information in your order: Part number, instrument type or
number, serial number, and modification number if applicable.
If a part you have ordered has been replaced with a new or
improved part, your local Tektronix, Inc. Field Office or
representative will contact you concerning any change in part
number.
Change information, if any. is located at the rear of this
manual.
IT E M N A M E
In the Parts List, an Item Name is separated from the
description by a colon (:). Because of space limitations, an Item
Name may sometimes appear as incomplete. For further Item
Name identification, the U.S. Federal Cataloging Handbook H6-1
can be utilized where possible.
F IG U R E A N D IN D E X N U M B E R S
Items in this section are referenced by figure and index
numbers to the illustrations.
INCH
It
NUMBER SIZE
ACTR
ACTUATOR
AOPTR ADAPTER
ALIGN ALIGNMENT
AL ALUMINUM
ASSEM
ASSEMBLED
ASSY ASSEMBLY
ATTEN
ATTENUATOR
AWG AMERICAN WIRE GAGE
BD
BOARD
BRKT BRACKET
BRS BRASS
BRZ
BRONZE
BSHG BUSHING
CAB CABINET
CAP
CAPACITOR
CER
CERAMIC
CHAS CHASSIS
CKT CIRCUIT
COMP
COMPOSITION
CONN
CONNECTOR
COV COVER
CPLG COUPLING
CRT
CATHODE RAY TUBE
DEG
DEGREE
DWR DRAWER
REPLACEABLE
MECHANICAL PARTS
A B B R E V IA T IO N S
ELCTRN ELECTRON
ELECTRICAL
ELEC
ELECTROLYTIC
e l c t l t
ELEMENT
ELEM
EPL ELECTRICAL PARTS LIST
EQUIPMENT
EOPT
EXT EXTERNAL
FIL FILLISTER HEAD
FLEX FLEXIBLE
FLAT HEAD
FLH
FLTR FILTER
FR FRAME or FRONT
FSTNR FASTENER
FT FOOT
FXD FIXED
GSKT GASKET
HANDLE
HDL
HEX HEXAGON
HEX HO HEXAGONAL HEAD
HEXAGONAL SOCKET
HEX SOC
HELICAL COMPRESSION
HLCPS
HLEXT HELICAL EXTENSION
HV HIGH VOLTAGE
INTEGRATED CIRCUIT
1C
INSIDE DIAMETER
1 0
IDENT IDENTIFICATION
IMPELLER
IMPLR
IN D E N T A T IO N S Y STEM
This mechanical parts list is indented to indicate item
relationships Following is an example of the indentation system
used in the description column
1 2 3 4 5
Assembly and/or Component
Attaching parts lor Assembly and/or Comoonent
Detail Part o l Assembly and/or Component
Attaching parts lor Detail Part
Parts o l D etail Part
Attaching parts lor Parts o l Detail Part
Attaching Parts always appear in the same indentation as
the item it mounts, while the detail parts are indented to the right
Indented items are part of. and included with, the next higher
indentation. The separation symbol — * — indicates the end of
attaching parts.
Attaching parts must be purchased separately, unless otherwise
specified.
INCH
IN
INCANDESCENT
INCAND
INSULATOR
INSUL
INTL INTERNAL
LAMPHOLDER
LPHLDR
MACH MACHINE
MECH MECHANICAL
MTG MOUNTING
NIP NIPPLE
NON WIRE NOT WIRE WOUND
OBD ORDER BY DESCRIPTION
OUTSIDE DIAMETER
OD
OVH OVAL HEAD
PHOSPHOR BRONZE
PH BRZ
PLAIN or PLATE
PL
PLSTC PLASTIC
PART NUMBER
PN
PAN HEAD
PNH
PWR POWER
RCPT RECEPTACLE
RESISTOR
RES
RGD RIGID
RLF RELIEF
RTNR RETAINER
SCH SOCKET HEAD
OSCILLOSCOPE
SCOPE
SCREW
SCR
Section 10— 2215A Service
Name & Description
SE SINGLE END
SECT SECTION
SEMICOND SEMICONDUCTOR
SHLD SHIELD
SHLDR SHOULDERED
SKT SOCKET
SL SLIDE
SLFLKG SELF-LOCKING
SLVG SLEEVING
SPR SPRING
SO SQUARE
SST STAINLESS STEEL
STL STEEL
SW SWITCH
T
TUBE
TERM TERMINAL
THO THREAD
THK THICK
TNSN TENSION
TPG TAPPING
TRH TRUSS HEAD
V VOLTAGE
VAR
VARIABLE
W / WITH
WSHR WASHER
XFMR TRANSFORMER
XSTR
TRANSISTOR
10-1