Switching Off The Recorder; Insertions And Error Messages; Remote Surveillance And Remote Access To The Recorder; Remote Surveillance Via Mobile Phone And Tablet Computer - Monacor IOR-204 Instruction Manual

8.13 Switching off the recorder

Prior to using the POWER switch, shut down the recorder
properly. Otherwise, settings or current recordings may be lost.
1) Show the toolbar: Either press the right mouse button or
move the mouse pointer to the centre of the lower edge
of the screen.
Fig. 8-31 Toolbar
2) Click the icon
3) Click the icon
the menu. The following message will appear:
Warnung
Recording was stopped successfully, you can turn
off the power safely now !
Abb. 8-32 Message to inform the user that the recorder can be
switched off
4) Switch off the recorder with the rocker switch at the rear.
Note (models IOR-204 and IOR-208): The power supply unit connected
has a low power consumption even when the recorder is switched off. If
applicable, switch the power supply unit off by means of a power strip
with on / off switch.
9

Insertions and Error Messages

Insertion Meaning
One or more cameras can perform intelligent eval-
uations (chapter 7.15). When the icon is clicked, an
event list will be shown.
When "Warning Unformat." is shown as well:
The hard disk is not formatted.
When "Warning Full" is shown as well: The hard
disk is full.
To format the hard disk and thus to delete all recordings:
Call up the menu "Device", select the hard disk in
H
the column "Select" and then click "Format HDD".
*
To change the overwrite mode so that the oldest record-
ings can be overwritten:
Call up the menu "Device", select the hard disk in
the column "Select" and then change the setting
in the field "Overwrite" (e. g. from OFF to AUTO or
reduce the number of days).
An alarm has been triggered via one of the alarm
I I
or * inputs (chapter 6.4). The backlight of the insertion
will be red when the alarm has started a recording.
NO HDD
No hard disk installed.
*
No Camera
The camera channel is not linked to a camera.
VIDEO LOSS
* No video signal available.
Motion detected in the camera image. The back-
M M
or * light of the insertion will be red when the alarm
has started a recording.
R
The camera image is being recorded.
An intelligent evaluation has been performed. The
S S
or *
backlight of the insertion will be red when the
evaluation has started a recording.
* At the same time, the internal signal device will sound for the time
range that has been defined in the menu "Parameter" or " Advanced"
(see chapter 7.9)
56
"Main Menu".
"Shutdown" in the upper right corner of
10 Remote Surveillance and
Remote Access to the Recorder
10.1 Remote surveillance via mobile phone
and tablet computer
Mobile phones and tablet computers with the operating sys-
i
tem "Android" or "IOS" can be used for convenient remote
surveillance.
1) Install the app "RXCamView" from the Apple "App Store"
i
or the Google "Play Store".
Fig. 10-1 App "RXCamView"
2) Start the app.
3) In the toolbar to the left, select "Config" (a) (Fig. 10-2).
4) In the line "Device" located in the upper right of the menu,
tap the plus sign (b).
Device
Live
Alarm
Playback
Favorites
Record
Image
(a)
Config
Help
RXCamView
Fig. 10-2 Window "Config" / "Device"
5) A pop-up menu will appear. Tap "Manual Adding" (c).
Device
Live
Device Name
Alarm
Playback
Login Type
Favorites
Device ID
Record
Media Port
Image
User Name
Config
Password
Channels
Help
RXCamView
Fig. 10-3 Window "New Devices"
6) "Device ID" should be selected in the line "Login Type". If
required, change the entry from "IP/ DOMAIN" to "Device
ID".
7) Tap the QR code icon in the line "Device ID", and then
scan the QR code which can be found on the upper side
of the recorder or enter the ID number provided on the
upper side of the recorder into the line.
8) In the line "Password", enter the password (no password
is factory-set in this line).
9) Finally click the diskette icon in the line "New Devices"
(located at the top of the window) or tap "Save".
Config
(b)
Device
Manual
(c)
Adding
Scan QR Code
Online Device
Create QR Code
Config
New Devices
DVR1
Device ID
Please enter the DDNS ID
9000
admin
Please enter password
8
Disconnected