Monacor IOR-204 Instruction Manual page 40

Network Configuration
PPPoE
Client Port 09000
IP Address 192.168.001.100
Subnet Maske 255.255.255.000
Gateway 192.168.001.100
DNS1 192.168.001.100
DNS2 008.008.008.008
UPNP Disable
Don't show this window next time.
Fig. 7-16 Network settings
4) If the recorder is not connected to a network, click "Next"
to go to the next menu and then continue with step 5.
For network connection, the static setting is recom-
mended. The following setting options are available:
Settings
PPPoE
Point-to-Point Pro-
tocol over Ethernet
(for DSL modems,
hardly used any-
more)
DHCP
Dynamic Host Con-
figuration Protocol
(factory setting)
Static
(recommended
setting)
UPNP
Universal Plug
and Play
When the network has been configured, click "Next".
5) The menu for adding IP cameras will appear:
Channel Edit State
CH1
CH2
CH3
CH4
Auto Assign IP to Camera(s) Channel Delete
Don't show this window next time.
Fig. 7-17 Adding IP cameras
When all cameras whose images are to be recorded are
connected to the recorder via the jacks LAN... (5 and 6),
click "Next" to go to the next menu and continue with
step 7.
IP cameras can only be added when they have been
connected to the network (see instruction manual of the
camera). For adding IP cameras, the following options are
available:
40
DHCP Static
HTTP Port 00080
×
Cancel Previous Next
With the option PPPoE, enter the user name
and the password supplied by the Internet
service provider and set the client port as well
as the HTTP port. It will then be possible to
remotely access the recorder via the IP address
captured after a domain name and the HTTP
port have been registered.
With the option DHCP, the router will auto-
matically assign an IP address to the recorder.
However, the IP address assigned can be
different with each restart. Consequently, port
forwarding is required for remote access to
the recorder (set UPNP to "Enable").
With the option "Static", enter the correct
IP address, subnet mask, gateway and DNS.
When the router supports the UPnP function
and when UPNP has been set to "Enable",
the recorder will automatically send the port
numbers to the router. For the recommended
setting "Static", the factory setting "Disable"
should be used.
IPC Setup
IP Adress/Domain Subnet Maske Port
Add All User-defined Add
Total band width:40Mbps, used band width:0bps
×
Cancel Previous Next
Button
CH...
Auto Assign IP
to Camera(s)
Channel Delete
Add All
User-defined
Add
When the IP cameras have been added, click "Next".
6) The menu for automatic recording will appear. According to
the factory settings, all camera channels to which a camera
is connected will record from 00:00 – 24:00.
Channel
0
S
M
T
W
T
F
S
Copy
Don't show this window next time.
Fig. 7-18 Weekly schedule for recordings
To change the settings:
a) After "Channel", the camera channel is shown (in the
figure above: channel 1). To change the recording time
for a different channel, click the icon
b) To delete recording times, keep the left mouse button
pressed and move the mouse pointer over the time range
desired. Individual half-hour blocks can be deleted by
a simple click.
c) Proceed in the same way to add times that have been
deleted.
M
d) To automatically start recording when motion is detected
and / or an alarm is triggered, first click the yellow ellipse
"Motion" or the red ellipse "Alarm". Then keep the left
mouse button pressed and move the mouse pointer over
the time range desired.
e) To use the setting for other camera channels as well,
make the appropriate selection in the line "Copy CH
... To All" at the bottom of the menu and then click
"Copy".
f) If required, the recorder can be easily reset to its factory
settings (chapter 8.10).
When the settings have been made, click "Next".
7) A menu for date, time, menu language and other basic
settings will appear:
Function
Click the plus icon to assign a specific IP camera
to a camera channel. The window "Quick Add"
will appear. Click "Search" to show all cameras
available in the network. Click the camera de-
sired to select it and then click "Add".
Automatic assignment
To remove a camera
(click to select the entire line of the camera)
To add cameras to all IP camera channels avail-
able
User-defined adding of cameras
Record Schedule
CH1 Normal Motion
2 4 6 8 10 12 14 16
CH1 To All Copy
×
Cancel
Alarm
18 20 22
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Previous Next

.