Controlling A Ptz Camera; Deleting Data - Monacor IOR-204 Instruction Manual

8.8 Controlling a PTZ camera

When one or more cameras are connected that can be
remote-controlled (pan, tilt, zoom, focus etc.), they may be
conveniently controlled by means of the recorder.
1) Use the left mouse button to click the live image of the cam-
era to be controlled. (In the single-image mode, simply press
the left mouse button.) The quick-selection bar will appear:
1)
Fig. 8-18 Quick-selection bar
2) Click the icon . The control window will appear:
CH1 SPEED
–
ZOOM
–
–
Fig. 8-19 Window for PTZ control
Menu item
Icon
CH...
arrows

SPEED

ZOOM
FOCUS
IRIS
3) To exit the control window, click the image with the right
mouse button.

8.9 Deleting data

When you want to dispose of the recorder or plan to give
(e. g. sell or lend) it to a third party, make sure to delete all
recordings and passwords: Format the hard disk and reset the
recorder to its factory settings. Otherwise, you will pass on your
recordings, personal data and passwords with the recorder.
1) Call up the main menu.
Either press the button MENU on the remote control
or use the mouse:
To show the toolbar, press the right mouse button or move
the mouse pointer to the centre of the lower edge of the
screen.
Fig. 8-20 Toolbar
In the toolbar, click the icon
Parameter Record Search
Display
Channel
IP Channels
IP CH1
Live
IP CH2
IP CH3
Output
IP CH4
Image Control
Privacy Zone
Record
Auto Assign IP to Camera(s)
Capture
Network
Alarm
Fig. 8-21 Main menu
54
20
+
+
FOCUS
+
IRIS
Function
To select the camera channel
To pan, tilt,
to pan and tilt at the same time
To enable / disable the automatic pan function
Pan / Tilt speed
To start / stop the camera cruise
To call up the window for saving camera posi-
tions for the camera cruise feature
Zoom function
To adjust the focus
To adjust the iris
"Main Menu" on the far left.
i
Device System Advanced
Edit State IP Addresse/Domain
10.10.25.151
10.10.25.152
Channel Delete Add All
Total band width:60Mbps, used band width:10.5bps
2) In the bar located at the top of the menu, click "Device".
Parameter
HDD
PTZ
Cloud
Fig. 8-22 Menu "Device", submenu "HDD"
3) Select the hard disk: In the column "Select", click the line
with the hard disk (see mouse pointer in the figure above).
4) Click the button "Format HDD". The window "Login"
will appear:
Parameter
HDD
PTZ
Cloud
Fig. 8-23 Window "Login"
5) When a password has been defined, enter the password.
Click "Login". The following confirmation window will
appear:
Entire Data Will Be Erased, Do You Want To
Fig. 8-24 Window for confirming formatting
6) Click the button "OK". A status bar will appear, indicating
the formatting progress. When formatting has been com-
pleted, the following message will appear:
Fig. 8-25 Hard disk formatted
7) Click "OK": The available capacity and the available
recording time will be shown.
i
8) To delete all passwords and other data, reset the recorder
(see next chapter).
Shutdown
Subnet Maske Port M
255.255.0.0 9988
255.255.0.0 9988
User-defined Add
Cancel
Record Search Device System
No. State Free/Total
1* OK 891G/931G
Overwrite Auto
Record Search Device System
No. State Free/Total
1* OK 891G/931G
Login
User I a dmin
Password
Login Cancel
Overwrite Auto
Notice
Continue?
OK Cancel
Notice
Format Completed
100%
OK
i
i
Advance Shutdown
Free Time Select
202STD
Format HDD
Default Save Cancel
i
Advanced Shutdown
Free Time Select
202Hour
Format HDD
Default Save Cancel