Remote Control Of Cameras (Ptz); Enabling The Snapshot Feature - Monacor IOR-204 Instruction Manual

Menu item Function
Channel To select the camera channel
To enable /disable the motion detection feature
Note: The motion detection feature can only be enabled
Enable
when the camera supports this function and when the
camera channel selected shows a camera image.
When motion is detected, the alarm buzzer will
Buzzer
sound for the time defined.
Sensitivity Sensitivity of the motion detection feature
1. Click
from the motion detection feature.
2. To activate multiple fields, keep the left mouse
button pressed and move the mouse pointer
over the respective fields. The motion-sensitive
fields are marked in red.
Area
3. It is possible to directly click individual fields.
4. The same procedure can be used to deacti-
vate fields.
5. To go back to the menu, click the right mouse
button in the camera image.
Duration of a recording that has been started via
Post Recordung
the motion detection feature
When motion is detected, the alarm relay (output
Latch Time ALARM or OUT, chapter 6.4) will respond for the
time defined.
When this field has been tick-marked: The alarm
Alarm Out
relay will respond when motion is detected.
A detected motion will be indicated
Show Message
by the icon M (Motion)
When motion is detected, an e-mail will be auto-
matically sent provided that the required specifica-
Send Email
tions have been made in the menu "Parameter",
submenu "Network", section "Email".
When motion is detected, the corresponding cam-
Full Screen
era image will be displayed in the full-screen mode.
Specification of the channels that are to be re-
corded when motion is detected (it is possible to
record multiple channels even if the motion has
been detected in one channel only).
The times of a motion-triggered recording must be
Record Channel
entered in the record schedule (menu "Parameter",
submenu "Record", section "Record schedule";
click the yellow, round-shaped selection field
"Motion" and, with the left mouse button pressed,
move the mouse pointer over the days / hours).
Save To save the setting
Cancel To exit the menu

7.13 Remote control of cameras (PTZ)

For remote control of PTZ cameras, make the required set-
tings at the recorder. Call up the menu "Device" and click
the submenu "PTZ".
Parameter Record Search
HDD
Channel
PTZ
Signal Type
Cloud
Protocol
Baudrate
DataBit
StopBit
Parity
Address
Copy CH1
Fig. 7-30 Menu to set the remote control of cameras
46
Setup to exclude specific detection fields
i
Device System Advance
CH1
Digital
Pelco-D
9600
8
1
None
001
To All Copy
Save
Menu item
Channel
Signal Type
Protocol*
Baudrate*
Data Bit*
Stop Bit*
Parity*
Address*
Copy
Save
Cancel
* These menu items are only relevant for the signal type "Analog" and
can only be set when the signal type "Analog" has been selected.
Please refer to the specifications of the camera for the settings
concerning protocol, baud rate, data bit, stop bit and address.

7.14 Enabling the snapshot feature

The snapshot feature allows you to save camera snapshots
manually and in a time-controlled manner. Call up the menu
"Parameter" and then click the submenu "Capture".
Parameter
Display
Record
Capture
Capture
Capture Schedule
Network
Alarm
Bewegung
Fig. 7-31 Menu to enable the snapshot feature
Menu item
Channel
Auto Capture
Stream Mode
Normal Interval
Alarm Interval
Shutdown
Manual Capture
Copy
Default
Save
Cancel
To define the times at which snapshots are to be taken auto-
Cancel
matically, click the section "Capture Schedule":
Function
To select the camera channel
Digital = PTZ control via the network cable
of the camera
Analog = PTZ control via the RS-485 interface (17);
only available for model IOR-232POE
To select the control protocol of the camera
To select the data transmission rate
Number of data bits
Number of stop bits
Type of parity bit:
None, Odd, Even, Mark (always 1), Space (always 0)
Address of the camera for independent control
of all cameras connected
To use the settings of a camera channel
for additional channels
To save the setting
To exit the menu
i
Record Search Device System
Channel CH1
Auto Capture Disable
Stream Mode Mainstream
Normal Interval 5 s Alarm Interval 5 s
Manual Capture Disable
Copy CH1 To All
Function
To select the camera channel
To enable time-controlled snapshots (set the record-
ing times in the section "Capture Schedule")
„Mainstream" = high resolution, high data volume
„Substream" = lower resolution, lower data volume
Intervals between recordings in normal mode
Intervals between recordings in case of an alarm
To enable manual snapshots
(see chapter 8.6.2 on how to take snapshots)
To use the settings of a camera channel
for additional channels
Reset to factory settings
To save the setting
To exit the menu
Advance Shutdown
Copy
Default Save Cancel